PCB
See Also: Printed Circuit Board, PCBA, Crosstalk
-
product
Automated Optical Inspection (AOI)
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
product
Combination Board Tester
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 230gf
K100-H080230-SKAU
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
product
IPC Inspection
Customers of MASER Engineering that are designing electronic products and thereby using bare and assembled Printed Circuit Boards (PCB's) are interested in the manufacturing quality of the PCB and assembling quality of the PCBA.
-
product
X-Ray Inspection System
MX1
Manncorp’s new MX1 is a high-performance x-ray inspection system designed for real time imaging of multilayer PCBs and dense metal BGAs, μBGAs, and chip scale packages. Its high voltage (80kV), computer-controlled x-ray tube and 35 μm focal spot provide the power necessary for detection of a variety of defects including bridging, voids, and missing balls. The MX1’s standard camera features continuous zoom magnification from 4X to 50X and variable angle viewing up to 45°, and an upgrade to the x-ray tube can boost magnification to 225X.
-
product
High Voltage Power Sources
Electronic Test & Power Systems
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules.
-
product
Failure and Technology Analysis
Failure analyses in order to clarify the failure cause soonest possible.From single device to the whole system - and from highly complex IC up to printed circuit board (PCB), mounting & interconnection technology and printed board assembly (PBA).
-
product
Header/Shroud Right Angle Kit, Receiver, QuadraPaddle, for Custom PCB Mounting
510109315
This kit is for mounting QuadraPaddle Receiver modules to custom-designed PCBs. Requires QP Receiver module p/n 510150130.If you do not have receiver module p/n 510150130, purchase the full RCV QP mounting kit instead,p/n 510150152.
-
product
Universal Diagnostic System
BoardMaster External Case Solution
The ABI BoardMaster External Case universal diagnostic system is a uniquely versatile and easy-to-use test system. It offers the most comprehensive set of test instruments for fault-finding on almost any kind of PCB. With the full range of instruments and a variety of test methods guaranteeing the best possible fault coverage, the BoardMaster External Case provides the ultimate in diagnostic tools.
-
product
Digital Interconnect Test System, Reference Solution
When you need to measure advanced S-parameters with a fast, low-cost and easy-to-use test solution, the Digital Interconnect Test System gives you a significant edge. It provides a full 32-port vector network analyzer (VNA) configured within a single PXI chassis – ideal for high-speed cable testing. And lets you test any linear passive interconnect faster and easier, including backplanes, connectors and PCBs. Sharpen your edge with Keysight’s Digital Interconnect Test System that enables signal integrity characterization of multiport interconnect products.
-
product
25-Pin D-Type Female Right Angled PCB
40-963-025-RF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Edge Card Adapter, Universal, for .062 PCB
111107138
VPC provides two types of Edge Card Adapter Kits for 10, 25 and 50 Module ITA Enclosures. Both kits are designed for various sized cards.The Universal Edge Card Adapter Kit’s card guides are hinged and can be folded for storage by releasing the holding latches on either side of the card.
-
product
9-Pin D-Type, Right Angled PCB, Male,HV
40-963-009-RM-HV
9-Pin Male Right Angled D-Type Connector, High Voltage - PCB Mount
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
Defect Review Station Software for electrical test
Faultstation
Centralize all error review for your different testers in a single seat! To capture PCB layout information, FaultStation offers the choice of DPF or IPC input. In combination with a Ucamco data-prep seat, DPF is the obvious choice, while industry standard IPC provides a doorway to all other data-prep systems in today’s marketplace. Once the layout data is available, you combine it with the error information from a variety of different models and makes of testers.
-
product
Resister
Our ARFC type Film Flat Chip Resistor & ARFCN type Thin Film Chip Resistor Network are high precision Metal Film resistors produced with high purity. Alumina Substrate and Ni-Cr-Si Resistor Film based on high precision Etching Technology. The electrode Terminals are made with Spattering Film and Nickel-Solder Plating, and solderability is very good in all Flow, Reflow and Dipping type soldering for Hybrid IC, SMT, PCB etc. Our ARFC Metal Film Resistor & ARFCN type Thin Film Chip Resistor are being produced under the thorough quality control, and are being used widely in high precision and high reliability electronics circuit such as Measuring Instrument, Medical Instruments, Communication and other Industrial Instruments.
-
product
Automated Soxhlet Extractor
Soxtec™ 8000
The Soxtec 8000 extraction unit is a fully automated system for fast and safe extraction of soluble matter from a wide range of matrices. It performs the four extraction steps boiling, rinsing, solvent recovery and auto-shut down, fully unattended. Just load, start and walk away. The Soxtec 8000 is specially designed to ensure the highest possible throughput and safety.Parameters: Crude fat, Total fat and Extractable matterSample types: Fat in food and feed. Extractable matter in textile, paper pulp, plastics, rubber etc. PCB and PAH in soil and sludge (the Soxtec is a preparatory step to GC-MS).
-
product
Pine Electronics
Specializing in low-mid volume electronic manufacturing services, Pine Electronics, Inc. offers a wide range of printed circuit board assembly (PCB assembly), cable and box build assembly solutions. Our equipment, engineering and technical talent serves both multi-national and regional customers throughout the United States. Known for full-service PCB assembly work, Pine Electronics, Inc. is highly integrated and responsive. Each customer has a designated representative for all commercial and technical questions. This personalized service model enhances communication, expedites project development, and represents Pine’s commitment to customer service.
-
product
High-speed 3D Solder Inspection Machine
YSi-SP
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
product
EOS Tester
KT-200SG
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
product
78-Pin D-Type Male Straight PCB Mount
40-963-078-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
Signal & Power PCB Connector
HPW Series
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
product
Probe Card Analyzers
PB6500
The Probilt PB6500 has many features that make it the ideal analyzer for all probe card technologies, including the latest probe tip geometries being used to test leading edge semiconductor devices. Its excellent electrical measurement capability and the ability to drive relays on any channel make it the best tool for probe cards with complex circuits and relays on the PCB.
-
product
Measuring and Calibration Stations
PCB
Is used to measure electric and magnetic fields of an ESD generator
-
product
PCB Adapter, ITA, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510108148
The 96 Pin ITA Signal Module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the Module.
-
product
Benchtop Electric Blast Drying Oven
Guangdong Test EQ Equipment co., Ltd.
- Precision & Uniformity: Multi-zone airflow design ensures ±2% temperature uniformity (per ASTM E1459). Auto-reversing fan eliminates hot/cold spots.- Rapid Drying: Turbo blast mode reduces drying time by 50% vs. conventional ovens (ideal for ceramics, polymers, and PCB coatings).- Durability: SUS304 stainless steel chamber, fiberglass insulation, and powder-coated exterior for corrosion resistance.- Smart Connectivity: IoT-enabled remote monitoring via mobile app (iOS/Android), compliance with FDA 21 CFR Part 11 for audit trails.- Energy Efficiency: ECO mode reduces power consumption by 30% during idle (ENERGY STAR® 2025 certified).
-
product
VTAC, Insert, Receiver/ITA, SIM, Vertical Header, 8 Pos
610151107
The VTAC vertical header insert contains 8 VTAC high speed contacts and is designed to mount directly to a PCB. It can be configured as a backplane connector and daughterboard connector. Also sold as a set with 610151108.
-
product
ATE
QT 200 NXG
Qmax Test Technologies Pvt. Ltd.
QT 200 Nxg a Highly sophisticated ATE, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software.
-
product
3-Pin Power D-Type Connector, 40A, Female PCB Mount
40-963-003-RF
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
product
Log-Periodic Antennas 400 MHz - 6.0 GHz
PCB Series
Our low-profile directional antennas are designed for wireless testing and communications from 450 MHz to 6.0 GHz and beyond. These antennas are etched on a low-loss microwavesubstrate. The broadband, log-periodic structure enables operation over a very wide frequency range with constant gain.
