Failure
See Also: Destructive
-
Product
Regenerative Battery Pack Test System
17020E
-
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
PXIe-1086DC, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis
787137-01
-
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis - The PXIe‑1086DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086DC monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
Product
Infrared Thermometer
6572
-
Peaceful Thriving Enterprise Co Ltd
6572 Infrared (IR) Thermometer is the non-contact way to make safe and quick temperature checks on mechanical equipment, electrical circuits and building systems while in operation. Regular monitoring of heat (infrared energy) emitted from surfaces can prevent potential problems and failures.
-
Product
Structural & Stress Analysis
-
Structural analysis is critical because it can determine cause and predict failure – evaluating whether or not a specific structural design will be able to withstand the external and internal stresses and forces expected for the design.
-
Product
BF-Series Standard Plus Models
-
The E-DRIV® BF-Series standard plus models feature a selectable Double Hit Mode for soft joint applications and a selectable Soft Start mode. Engineered for high volume manufacturing applications the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
Materials And Chemical Analysis
-
Anderson Materials Evaluation, Inc.
Materials characterization, failure analysis, quality control, and materials and process development services are offered. Our analytical techniques allow us to assess elemental and chemical material composition, thermal properties, coating thickness, electrochemical properties, surface chemistry, surface wetting, corrosion rates and pitting potentials, contamination and degradation problems, metallography, fractography, phase transitions, static coefficient of friction, adhesive bonding strength and causes of adhesive bonding failures, surface tension and surface energy, tensile and compressive strength, bend deflection, lapshear strength, elasticity properties, UV and visible light absorption and reflection, density and porosity, and many other material properties integral to improving your products.
-
Product
Failure Analysis
MicroINSPECT 300FA
-
The MicroINSPECT 300FA is an automated wafer inspection tool used for semiconductor wafer failure analysis. Its small footprint, high speed, and low cost relative to its rich features yield a superb cost of ownership and makes this an ideal tool for your fab or failure analysis lab. The MicroINSPECT 300FA combines advanced robotics, wafer sorting, an intelligent wafer inspection microscope together with SiteVIEW Software to produce an integrated failure analysis tool.
-
Product
Generation Protection
-
Schweitzer Engineering Laboratories, Inc.
SEL generator protection solutions provide complete primary and backup protection from all types of faults. Using these devices helps you avoid expensive equipment damage and failure while maintaining system performance and increasing availability.
-
Product
Tower Light Monitor
1750-TLM
-
Designed with the Broadcaster in mind the 1750-TLM provides built in flexibility to simplify even the most complicated installations. It can even alarm for single bulb failures on towers with Beacons and Obstruction lights on a single circuit. Status oututs eliminate the worry of operator interpretation and provide definitive Good-Bad indications for the operator and your logging equipment. Don’t let tower light failures expose you to increased liability, the 1750-TLM is compatible with most existing control equipment and may well provide your best return on investment this year!
-
Product
Chloride Ion Test Kit for Abrasives
134A
-
Contamination can build up, particularly if the blast media is recycled several times. Using the Elcometer 134A Chloride Ion Test in the field will accurately identify contamination and prevent costly surface-related failures.
-
Product
Ceramics and Glass Inspection Systems
-
Due to their special material properties, ceramic and glass components are the basis of many high-tech products. The same properties make the production complex and costly. Substrate defects that lead to failure of finished components should be avoided at all costs. For this reason, early automated optical inspection is essential.For the inspection of sapphire and quartz glass Intego has developed systems to detect both external and internal defects and can also provide cutting suggestions. Using index matching it is possible to test rough or uneven glass profiles.For the inspection of ceramic components Intego offers solutions specifically tailored to the respective testing task. Our modular design uses standard components that have already been developed and tested and in most cases only requires minimal adaptation.
-
Product
Destructive Physical Analysis & Failure Analysis
-
DPACI's component analysis laboratory performs major analytical functions, such as destructive physical analysis, failure analysis, counterfeit analysis, and material analysis on components & devices. Our destructive physical analysis techniques are performed in accordance with standards and methods used in most military and space program requirements. Solutions for difficult production problems are resolved through our failure analysis procedures.
-
Product
System Modeling for Diagnostic Design and Analysis
EXpress
-
eXpress is a comprehensive model-based diagnostics engineering software application providing an environment for the design, capture, integration, evaluation and optimization of complex or large-scale system diagnostics, prognostics health management (PHM), systems testability engineering, failure mode and effects analysis and system safety analysis. eXpress is uniquely suited to influence the diagnostic development for new designs or to exploit the diagnostic challenges of existing legacy systems. Its robust structure facilitates the capture of extensive interdisciplinary design knowledge providing an unmatched ability to corroborate, reuse and re-purpose expert knowledge in performing standardised testability, reliability and maintainability analyses.
-
Product
Leak Tester
AD-1690
-
Are you sure your pipettes are all accurate? Most pipette failures happen due to soiled or damaged parts compromising the airtightness of the pipettes. With the AD-1690 leak tester, you can instantly spot the pipettes that need to be fixed.
-
Product
X-ray Inspection Performance
MXI Quadra 7
-
Ultimate image quality and magnification, Quadra 7 reveals quality defects as small as 0.1 µm. Ideal for root cause failure analysis, wire bond integrity checking, component cracking, MEMS inspection and wafer level components including TSV and wafer bumps.
-
Product
ASI/SD-SDI Input+output With Relay Bypass For PCIe
DTA-2145
-
General-purpose DVB-ASI input and output, also SD-SDI capable. A relay automatically connects input port to output port upon software- or hardware failures, enabling highly-available system configurations without requiring a failover switch.
-
Product
Durable, Ultra Small & Flexible Test Assembly
StormFlex® 034
-
Storm Flex® line of flexible cables, the 034 diameter cable offers the same superior mechanical benefits in a new miniature size.Its ruggedness and durability combined with its ultra-small size, very low weight, and extreme flexibility make Storm Flex® 034 cable assemblies the perfect fit for applications such as:- Test & Measurement ~ where flexibility and robustness minimize mating errors.- Systems ~ with complex installation or deployment that can compromise mechanical & RF stability.- Gimbal ~ with requirements for cables operating to 50 GHz.- Digital Test ~ needing minimized stress at the connector to connector interface.- High Density ~ utilizing multi-cable interconnects with centerline spacing as low as 0.07 inches.Storm Flex® 034 cable is also recommended as a semi-rigid replacement in applications where a sem-rigid cable is impractical to deploy and routing may result in assembly breakage or electrical failure.
-
Product
DGN Advanced Reporting Feature, GTE 10.00p
K8223A
-
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
Product
E-DRIV® Brushless Electric Screwdrivers
LF-Series
-
The LF-Series is an economical brushless screwdriver. The durable power tool features a Swiss Maxon brushless motor, which reduces the common maintenance costs associated brush type electric screwdrivers. The electric screwdriver is ESD safe, ensuring less than 1 Ohm at the bit tip. ESD management in power tools ensures product quality, cost savings and a reduction in overall ESD failures. Manufacturing engineers involved with microelectronic products are aware of the importance of controlling Electrostatic Discharge (ESD) failures. Lapses in preventing the occurrence of electrostatic discharge can affect production yields, manufacturing costs, product quality, product reliability, reputation and profitability.
-
Product
Cryocoolers
MT
-
The MT cooler has been in production since 2003 and is based on the CT cooler design. It was developed for the customer who did not need the lift of the CT cryocooler and wanted size and weight reduction for their application. The MT has been used successfully in applications such as High Temperature Superconductivity (HTS) filters, high altitude balloons, refrigeration, germanium detectors, IR detectors, radio telescopes, laser diode cooling, and research among others. We believe the customer will agree that the CryoTel® MT is the smallest 5W @77K cooler available at an attractive price point with a Mean Time to Failure of over 200,000 hours.
-
Product
Regenerative Battery Pack Test System
17040
-
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
DI Lab System™
-
Comprehensive Product Engineering and Failure Analysis Lab system for complete device analysis and physical defect isolation.
-
Product
SF6 Gas Purity Tester
-
Weshine Electric Manufacturing Co., Ltd
In operation and during electrical failures, pollutants are generated which, depending on its concentration, reactivity and toxicity, modify the characteristics of gas for insulation and arc extinguishing. This may affect the safety of the installation and people. Gas handling operations can also cause the incorporation of pollutants.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Heavy Duty Dynamometers
MD-7500-HD
-
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
Product
Failure Analysis Services
-
Innovative Circuits Engineering, inc
Innovative circuits engineerin's failure analysis group performs root cause analysis on a wide variety of integrated circuit devices.
-
Product
PXI Medium Density Switch Matrix Modules
-
Pickering's range of medium density switch matrix modules is a cost-effective solution for applications that require mid-range matrices in the PXI format. Selected modules are supported by our Diagnostic Test Tools, Built-In-Relay-Self-Test (BIRST) and eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
Product
DigitalClone
-
Operators use DigitalClone Live to understand when failures can be expected in their fleet, which assets, systems and critical components will begin to fail and which life extension actions will provide the greatest return on investment.
-
Product
Highly Accelerated Life Testing (HALT)
-
Quickly validate reliability and identify manufacturing defects that could cause product failures in the field with MET’s Highly Accelerated Life Test (HALT)HALT technique uses a combination of accelerated stresses to expose product flaws early in the design and manufacturing stages, which improves product reliability and customer confidence inherent to the design and fabrication process of a new product as well as during the production phase to find manufacturing defects that could cause product failures in the field.
-
Product
Verification And Diagnostic Tools
Y1131A
-
Provides module-specific tests to troubleshoot relay failures and predict maintenance requirements.
