Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
PXI-8430, 4-Port, RS232 PXI Serial Interface Module
778983-01
Serial Interface
4-Port, RS232 PXI Serial Interface Module - The PXI‑8430/4 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
Switch Blade
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
Desalter Interface Level Transmitter
-
This reliable level transmitter is specially designed to maximize the throughput of oil/water separators and accurately measures the electrical interface in the emulsion even in upset conditions. This measurement is critical because the separation vessel operates at maximum efficiency when the electrostatic grid is close as possible to the interface.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
Shuttle Bus VMC Intelligent Interface Card
IIB-SB-VME
-
The Shuttle Bus VME is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, andMultiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a VMEplatform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include LDB_BCT,LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
GPIB Analog Interface
Model 4861B
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
Multi-Protocol Interface for USB or Ethernet Equipped Computers
EXC-Unet2/Px
-
Multi-Protocol Interface for USB or Ethernet Equipped Computers
-
Product
Ethernet To Modbus RTU Minibox™ Interface
-
ICS's Model 9099 Ethernet to Modbus RTU Interface is a small Minibox™ Ethernet Modbus Converter that converts Modbus TCP/IP, VXI-11 and Raw Socket to control Modbus RTU Slave Devices. The Model 9099 does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX, Windows 2K or later and Modbus capable PLCs. ICS's 9099 uses VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
Product
Interface Technology Basic Line
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Covers all major standard applications in the control cabinet. It is as unique as our well-known high-end products, but much cheaper. Thus, the Basic Line is ideal for all electrical equipment, engineering companies and many other industries where very good just good enough.
-
Product
sbRIO-9853, Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module
780923-01
CAN Interface
Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module—The sbRIO‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA‑based applications with the NI‑RIO driver on CompactRIO. These modules are ideal for low-level FPGA‑based control and triggering applications that are programmed using the NI LabVIEW FPGA Module. These modules also are ideal for byte-level manipulation of CAN frames in the NI LabVIEW FPGA Module. The sbRIO‑9853 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
-
Product
Modbus Register Converter - Serial To Modbus RTU Interface
-
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.
-
Product
E33 Interface Solution With FFC Connector
E33-xFA
-
Encoder with integrated PCB and FFC conncector
-
Product
Intelligent Interface Card
IIB-1553-ISA
-
The IIB-1553-ISA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-ISA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multilevel triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable.The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
GPIB to Ethernet to Instrument Interface
Model 4865B
-
* Adds a GPIB Interface to Instruments with a VXI-11 or Raw Socket Ethernet Interface.* Transparent data transfer handles ASCII and binary data.* Controllable with any IEEE-488.2 GPIB Controller* VXI-11 protocol supports control, abort and reverse channels.* Raw Socket protocol includes substitute command strings for GPIB Device Trigger, Device Clear and Interface Clear.* Auto-Find feature simplifies instrument linkage* Reuses existing test software with new Ethernet instruments.* Easy configuration with the 4865B's internal webserver.* Drop in replacement for the original Model 4865 with 2x to 5x speed increase.* 1 U high rack mount kit mounts one or two 4865Bs.* Includes universal 115/230 VAC Power Adapter.
-
Product
18.5" HD, 1366 X 768, VGA/DVI/HDMI Interface, Panel Mount Monitor
IDS-3218W
-
18.5" 1366x768 HD LCD panel with LED backlight for 20% power saving, 0° ~ 55° C wide range operating temperature. With 5-wire resistive or P-cap touchscreen solution (optional) Touch interface: USB and RS-232.
-
Product
Automatic Test Equipment, Test Interface Units and Test Program Sets
-
Axis Aerospace & Technologies Ltd.
AXISCADES is a pioneer in Test Solutions and has a long pedigree in developing Test Systems. AXISCADES has designed and developed Automatic Test Equipment, Test Interface Units/Interface Test Adapters and associated Test Program Set Software for Indian and Global, Aerospace and Defence OEMs and End Users.
-
Product
GPIB To ANSI X3.28 Interfaces
-
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
Product
15" 1024 X 768, VGA/DVI/HDMI Interface, Front IP65 Monitor
IDS-3315
-
Front IP65 for waterproof and dustproof, 15" XGA LCD panel with LED backlight for 20% power saving and environmental protection. -20 ~ +60 °C wide range operating temperature, 5-wire resistive and P-cap touchscreen solution or tempered smudge resistant protected glass.
-
Product
Power Interface Board 6U, 1 PSU connector
106PIBM601-0000R
-
The PIB 6U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
PCI 16 Isolated Input Digital Interface (3-13V)
8006
-
The 8006 PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments.
-
Product
Interface Terminals
-
Panasonic Industrial Devices Sales Company of America
Panasonic's RT-3 Series 4-Point Terminal, Unit Relays are slim, space-saving and have four independent points on a base which contribute to a more compact control panel or interface terminal. These Relays can be mounted on a DIN rail or mounted directly and all are equipped with an LED display to allow easy confirmation of operation.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
Digital I/O
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
Product
USB2.0 to VME interface
SIS3150-USB
-
The SIS3150-USB is a high performance USB to VME interface. Connected to a USB2.0 port it supports block transfer speeds in excess of 30 MByte/s. USB1.1 operation is supported also. With the TigerSHARC DSP option it is perfectly suited for hard realtime applications.
-
Product
Interface Technology Style VXI Module Shield Kits
-
*Encloses Interface Technology style, slotted-edge, C-size PC boards All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. * All kits are available with customized front panels and side shields.
-
Product
2-Port Serial Interface
APCI-7420-3
-
*RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without optical isolation*Modular structure through MX-modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer common interrupt*Automatic direction recognition for RS485*Transmission mode: asynchronous, full, half duplex
