Serial to Parallel
-
product
10RJ50-DB9M Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)
182845-01
S8 Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)
-
product
16-Port RS232 Async Serial Communications Adapter PMC
2238
The Technobox 16-Port Async Communication adapter provides sixteen 16550-based UARTs using RS232 signaling levels.
-
product
Single Port RS232 Serial Communications Compact Flash Card With Ruggedized Connector
CF232-R
The CF232 is a tiny Type I format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters). The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
product
3U CompactPCI Serial Blades
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
product
Programmable Serial Device
HR-16P
The HR-16P is a programmable RS-232 serial device designed to control any device with a serial port based on sensing level changes (open-to-close and close-to-open, or digital high to low and vice versa).
-
product
GPIB to Parallel Printer Interface
Model 4892B
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
product
Serial Link Analyzer
HOTLink
The HSLA is a low-cost data recorder and diagnostics tool for 8B/10B encoded HOTLink systems. Each HSLA is preconfigured for a specific link speed (between 160Mbps to 1.0625 Gbps), and a connector type - copper (BNC, FCN, or SMA) or optical. The HL2View software makes data capture and analysis quick and easy.
-
product
Quad Channel Serial Communication Controller
CPCI-SCC04-ISO
The CPCI-SCC04-ISO Module is a quad Channel serial Communication controller with 2K Fifo per Line. The CPCI-SCC04-ISO module is based on 4 enhanced Z85233, with larger FIFOs and several SDLC improvements from Zilog. This module provides four synchronous ports up to 230 kbaud synchronous ports and up to Data Rates up to 5.0 Mbit/Sec full-duplex channels, with an independent baud rate generator for each channel.
-
product
Serial FPDP Rugged Rackmount Recorder
Talon RTR 2756
- Designed to operate under conditions of shock and vibration- Complete Serial FPDP record and playback system- Up to 8 I/O channels in a single 4U 19-inch rugged rackmount PC server chassis- Removable SSDs- Up to 38.4 terabytes of storage to NTFS RAID disk array- Copper, single-mode and multi-mode fiber interfaces available- Real-time aggregate recording rates of up to 5 GB/sec in eight-channel configuration- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- RAID levels of 0, 1, 5, 6, 10 and 50- Optional N+1 redundant power supply- SystemFlow® GUI virtual instrumentation panel for fast, intuitive operation- C-callable API for integration of recorder into applications- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor
-
product
Parallel Test Systems
Our parallel test systems for research and development are highly flexible in use and easily adaptable to different tasks as well as changing piezoelectric materials and designs.
-
product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
product
Smart GPIB Serial Interface Board
Model 4816
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
4 Serial Communication Channels, Programmable RS-232/422/485, Isolated
SC5
Serial Communication Module SC5 provides up to 4 high-speed, programmable RS-232/422/485, individually isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel isolated returns are available as part of the channel user interface signal set (for SE or ISO-GND reference).
-
product
GPIB Smart Serial Interface
Model 4866
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
product
Serial Parallel Interface
Model 2303
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
product
4 Serial Communication Channels, Multi-Mode Programmable, Isolated
SC2
Module SC2 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications.
-
product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 4000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M4KSerialPlus module is supplied with C drivers, including source code.
-
product
Massively Parallel Parametric Test System
P9001A
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
product
3U CompactPCI Serial 9-slot SSL w/o RTM w/ Ethernet
1CPCIS-309-L200
3U CompactPCI Serial Backplane with 9 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 8x CompactPCI S.0 peripheral slots, without connectors for Rear Transition Modules (RTMs), Ethernet full mesh.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
product
Serial Converters/Isolators/Repeaters
ULI-200
To keep your serial equipment communicating and smoothly integrated with new technologies, B B SmartWorx powered by Advantech has developed the most extensive line of serial conversion and isolation products on the market.
-
product
GPIB Serial Interface
Model 4804B
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
Free Serial Port Tools
*The clever terminal program for serial port and field-bus communication.*Build your own sending dialogs and create customized user interfaces *Simulate field-bus telegrams *Play Modbus ASCII/RTU master with predefined Modbus function dialogs
-
product
3U CompactPCI Serial 6-slot SSL w/ RTM w/ Ethernet
1CPCIS-306-L210
3U CompactPCI Serial Backplane with 6 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 5x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 2 to 6, Ethernet full mesh.
-
product
PCIe-8431, PCI Express, 8-Port, RS485/RS422 Serial Interface Device
780592-01
The PCIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
LW20/C Sealed Mini Laser Rangefinder, Serial – 100 M
28055
The compact, lightweight LW20/C Sealed Mini Laser Rangefinder is the ideal choice where size and weight matter yet protection is needed in outdoor environments. This sensor can perform distance sensing with first and last return signals for multi-obstacle environments. Its serial interface can be utilized by many different microcontrollers, with selectable data rates between 48 and 388 readings per second.
-
product
6U Compact PCI Multiport Serial Card
CP69002
LinkedHope Intelligent Technologies Co.,Ltd.
CP69002 is designed as 6U Compact PCI Multiport Serial Card. The eight serial ports are in depended and magnetic isolated. The transform mode can be configured as RS232, RS422 and RS485 through the jumpers. The upstream interface is 32 bit 33MHz PCI bus.
