Headers
-
Product
Ribbon Cable Headers
DINterm64
-
Ribbon cable headers are commonly used with VME compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The DINterm64 converts from 64 pin ribbon cable to a 64 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
Product
Tool, Press Kit, i2 PCB Headers
910121199
-
Tool, Press Kit, i2 PCB HeadersAids in pressing fit pins into the header.
-
Product
Ribbon cable headers
HDRterm50
-
Ribbon cable headers are commonly used with IP compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The HDRterm50 converts from 50 pin ribbon cable to a 50 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
Product
ESP8266 WiFi With Headers
Feather HUZZAH
-
Flagship development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Assembled Adafruit Feather HUZZAH ESP8266 with headers. At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core.
-
Product
Header, i2 Micro iCon, Receiver, 84 Pin, for PCB Mounting
510109204
-
Header, i2 Micro iCon, Receiver, 84 Pin, for PCB Mounting.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
SparkFun ESP8266 Thing
Dev Board (with Headers)
-
This is the SparkFun ESP8266 Thing Dev Board --- a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
64 Channel 12C GPIO Expansion
FXA-102 I2C Expander
-
The FXA-102 provides 64bit of General-Purpose Input / Output (GPIO) which are controlled via I2C. It is 3,3V and 5V compatible and based on four 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. Using the optional Phoenix Contact UMK housing, the FXA-102 can be installed on a DIN rail. The dual row 2,54mm pin headers allow usage with IDC20 connectors or wire wrap cables.
-
Product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
-
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Development System
FE-C450
-
* Emulates Dallas Semiconductors DS89C450 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Reflector
NetProbe 10GR
-
The NetProbe 10GR reflector provides loopback functionality in a low-cost, handheld device. It’s a smart loop device that swaps the source and destination addresses in MAC and IP headers as necessary to run Ethernet performance tests.
-
Product
SparkFun RJ45 Breakout
-
RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a lot of conductors. This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create your own RJ45 cable. Check the related items for Ethernet cable and connectors to go with it!
-
Product
Pin Converters
-
Blackhawk provides several different emulation pin converters to fit Texas Instruments standard JTAG target headers. This includes 14-pin TI, 20-pin cTi & ARM, 10-pin ARM, 60-pin XDS560 Trace and System Trace. All pin converters are available from the our Online Store or an authorized Blackhawk reseller.
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 6x32-Pin Ribbon Cable Headers
510151125
-
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 6x32-Pin Ribbon Cable Headers
-
Product
USB 2.0 Adapter
ADP-USB-445
-
The ADP-USB-445 USB 2.0 adapter converts one of the USB 2.0 headers on-board the WINSYSTEMS SBC35-427 single board computer to two type-A connectors on the front I/O panel. The integrated circuitry ensures noise immunity from the type-A connections to the single board computer and provides a robust power solution for external devices.
-
Product
Development System
FE-51RD2
-
* Emulates Atmel AT89C51RD2, AT89C51ED2 and others * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Micro Power, Header Insert, Receiver/ITA, SIM, Right Angle, 2 Pos, 2 Slot
510181103
-
This header insert contains 2 right-angle micropower contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module.
-
Product
Single row PCB connector
RBA Series
-
Smiths Interconnect's RBA series is a rugged stick header that can be cut to sizes up to 27 positions
-
Product
Development System
FE-51CC01
-
* Emulates Atmel T89C51CC01/2 and T89C51AC2, T89C5115 * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
Pocket AVR Programmer
-
This new version uses an SMD 5x2 header. This is a simple to use USB AVR programmer. It is low cost, easy to use, works great with AVRDude, and is tested extensively on a Windows desktop. Based on Dick Streefland's USBtiny and Limor Fried's USBtinyISP. This is a low-cost programmer designed for those on a tight budget.
-
Product
SparkFun LED Driver Breakout
TLC5940 (16 Channel)
-
The TLC5940 is a 16 channel PWM unit with 12-bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
-
Product
Analog Interface Boards
Model 4861B OEM
-
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
Product
1-, 10-, 40-Gigabit Ethernet Portable Recorder
Talon RTR 2735A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight, approximately 25 pounds- Shock- and vibration-resistant SSDs perform well in vehicles, ships and aircraft- Records gigabit, 10-gigabit or 40-gigabit Ethernet streams- TCP and UDP protocols- Copper or optical interfaces- Aggregate recording rates to 4.0 GB/sec- Windows® Server 2016 workstation with a high performance Intel® Core™ i7 processor- Up to 61 terabytes of SSD storage to NTFS RAID solid state disk array- Multiple RAID levels, including 0, 1, 5, and 6- SystemFlow® GUI with Signal Viewer analysis tool- C-callable API for integration of recorder into applications- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
Product
Magnetic Rotary 3 Click
-
Magnetic Rotary 3 Click is a compact add-on board for accurate magnet-position sensing. This board features the AS5147, an SPI-configurable high-resolution rotary position sensor for fast absolute angle measurement over a full 360-degree range from ams AG. The AS5147 position sensor suppresses the influence of any homogenous external stray magnetic field, equipped with a revolutionary integrated dynamic angle error compensation (DAEC™) with almost zero latency. It also comes with onboard headers reserved for incremental and commutation signals of their respective A/B/I and U/V/W signals alongside embedded self-diagnostics, including magnetic field strength too high, magnetic field strength too low or lost magnet, and other related diagnostic features. This Click board™ has been designed to support BLDC motor commutation for the most challenging automotive applications.
-
Product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
-
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
Product
Universal LightProbe Sensor Six-Pack
S6P
-
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
Serial Parallel Interface
Model 2313
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
