-
product
Flow Meter
V-Cone
The V-Cone Flow Meter is an advanced differential pressure instrument, which is ideal for use with liquid, steam or gas media in rugged conditions where accuracy, low maintenance and cost are important. With its DP built-in flow conditioning design, the V-Cone is especially useful in tight-fit and retrofit installations in which the long runs of straight pipe required by Orifice Plates, Venturi Tubes, and other technologies are either impractical or unavailable.
-
product
Oxidation Stability & Cold Flow Properties
These Anton Paar instruments enable you to evaluate the oxidation stability as well as the storage and thermal stability of mineral oil products or oil and fat containing cosmetics and food samples. The gum content tester is available for tests on the gum content of fuels and other volatile distillates. Cold flow properties (cold filter plugging point and cloud and pour point) show the lowest temperature for a trouble-free operation of diesel fuel or heating oil.
-
product
Melt Flow Testers
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
product
Lake Paddle Wheel Flow Meters
Operating much like a turbine flow meter, the paddle wheel flow meter consists of a freely rotating wheel which is outfitted with magnets on the blades or “paddles” of the wheel. As the fluid flows through the meter, spinning the wheel, sensors detect the magnets with each pass.
-
product
DIN Viscosity Flow Cups
2350
The Elcometer 2350 DIN Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
product
Photonic Hall Effect
HMS7000
Classic hall effect measurement system is to read voltage difference made between both diagonal sides, when flowing current and applying magnet field strength, in perpendicular to flowing current direction. - Photonic hall effect measurement is to read various electrical properties by illuminating light of “various range of wavelength” on the sample, in addition to flowing current and applying magnet field strength. - It is great to see “RGB (Red, Green, Blue), Light intensity vs carrier density, carrier mobility, resistivity, hall coefficient”
-
product
Electronic Inspection Systems
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
product
Washwater Monitoring System
EG-100
Washwater Monitoring System for NOx and SOx Scrubber.Monitoring pH/Temperature, Turbidity, and PAH.EG-100 has flow type sensors.
-
product
Flow, Level & Valves
We have an extensive range of flow controllers and flow indicators for both liquid and gas applications. We specialize in flow measurement and control of media in flow lines less than 2". Our level control instrumentation is perfect for use with small to medium process and industrial tanks and storage vessels. Choose from level sensors, float switches, optical switches, and ultrasonic transmitters/controllers for single-point control, dual-point control, continuous-level control, and leak detection. Our valve selection offers solutions to meter and control fluids in laboratory, process, and industrial applications. Types of valves available include options from simple and inexpensive plastic ball valves to actuated solenoid and manifold valves. Other types of valves include check, diaphragm, elliptical, metering, needle, pinch, proportioning, and stopcocks. To fit your fluid path, connection types include barbed, compression, luer, sanitary clamp, NPT, and true-union.
-
product
*Laser Thermal Power Sensors
Thermal sensors have a series of bimetallic junctions called a thermopile. Radial or axial heat flow through the sensor creates a voltage proportional to the power absorbed as it flows through the thermopile. The reading is not dependent on the ambient temperature since only the temperature difference is measured and not the absolute temperature. The thermopile elements are so arranged that the reading is almost independent of beam size and position. Generally, Ophir specifies ±2% or better uniformity of reading over the surface.
-
product
MASTER FUEL PRESSURE TEST KIT
FIT550
*Performs running, residual, rail and flow rate pressure tests*Large, easy-to-read 3-1/2" dual-scale gauge reads 0-100psi and 0-700 kPa*Kit includes: 50+ adapters, fittings, 48" hose, pressure relief and fuel discharge hose to test most domestic and foreign fuel injection systems*Also includes quick release couplers and adapters to fit other fuel injection test kits*For use with gas engines only
-
product
Control Center
Schweitzer Engineering Laboratories, Inc.
The essential elements in the reliable operation of the bulk electric system (BES) are control centers that continuously monitor and control generation and transmission power flows. Visualization, situational awareness, and analytic software help ensure that control center personnel always know what is happening with the BES.
-
product
Low Voltage Test & Measurement
Low voltage testing is able to catch errors such as shorts and opens by applying current to a wire and measuring the voltage. The wire will have a current affected by several factors including resistance and components. If the wire is connected correctly, the test will read low resistance. That means current is flowing through the wire as expected and reaching the required connections. If the tester reads high resistance it means something is impeding the current from reaching its destination. This could be caused by a number of causes.
-
product
Insertion Flow Meter
SPI Mag
The SPI Mag Insertion Flow Meter provides a highly cost-effective solution for the accurate measurement of liquid flow in closed conduit, pressurized pipe applications. Unlike conventional magnetic meters, the SPI Mag's cost is independent of pipe size.
-
product
CEAST VisualMELT Software
VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.
-
product
Reliability Testing
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
product
Vigilant Aircraft Hygrometer
137
The Edgetech Instruments Model 137 Vigilant Aircraft Hygrometer is a rugged, shock mounted military qualified instrument used for the primary measurement of dew point in flight or in installations with existing flow, such as wind tunnels.It features a miniature remote dew point sensor employing a platinum resistance thermometer, and has 15 feet of interconnecting cable to the control unit. Precision calibration units for the linear analog outputs are included.
-
product
PAR Quantum Radiometric Probe
LP471PAR
Quantum-radiometric probe for measuring the PHOTONS FLOW in the chlorophyll field PAR (photosynthetically Active Radiation 400nm…700 nm), μmol m-²s-¹ measure, cosine correction diffuser.
-
product
Propeller Meters
Measures accurately over a flow range of 10:1 or greater.± 2% of rate accuracy, guaranteed by certified wet calibration at three test points in.Sparling’s National Institute of Standards and Technology (NIST) traceable hydraulic flow lab.Sturdy cast or fabricated steel construction.Operating temperatures are over 100° F(unless higher temperature construction is specified).Suspended solids are over 0.5% of volume.Easily maintained with standard tools.Registration can be furnished in any standard Engineering Unit.
-
product
Electromagnetic Flow Meters
Magnetic flow meters, also known as electromagnetic flow meters or mag meters, are often selected because they are obstruction less, cost-effective, bi-directional, and highly accurate flow meters.
-
product
Pressure Sensor Kit for Changing Ranges
DP15TL
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
product
Paddlewheel Flow Sensor
2537
The Signet 2537 Flow Sensor is the next generation in fluid measurement technology from the inventor of the original paddlewheel flowmeter. This sensor is an enhancement on what is already an industry standard. It has the added functionality of various output options including flow switch, pulse divider, digital (S3L) or 4 to 20 mA. Additionally, it offers low flow, low power and high resolution and can be configured on-site directly through the built-in user interface.
-
product
Differential Pressure Flow Meters
Engineers can rely on the V-Cone dp flow meter to make life easier. McCrometer’s differential pressure flow meter is the versatile, highly compatible flow measurement solution for a variety of industries. When accuracy and repeatability are critical, the V-Cone’s performance brings superior value.
-
product
Ultrasonic Meters
E-Series
E-Series Ultrasonic water meters from Badger Meter use solid-state technology in a compact, totally encapsulated, weatherproof, and UV-resistant housing, suitable for residential and commercial applications. Equipped with an easy-to-read, 9-digit LCD display, the ultrasonic meter reports consumption, rate of flow, reverse-flow indication, and alarms. With no moving parts, the E-Series Ultrasonic meter improves reliability and has greater extended low flow accuracy compared to mechanical meters.
-
product
Syringe Pump
500x
The 500x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter up to 204 mL/min. Exceptional low-flow stability at up to 5,000 psi (345 bar) makes this the ideal pump for high pressure applications from deep well core analysis to a wide range of chemical applications.analysis to a wide range of chemical applications.The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 500x pump module has a single-ratio drive train with auto-lubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. Hastelloy cylinders are available for chemical compatibility of corrosive solutions. Single and continuous valve packages are 100% Hastelloy for full compatibility. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
product
Online Slurry Elemental Analyzer
SlurryView
Lyncis Online Slurry Analyzer is providing continues elemental analysis of slurry without a need for a complex and high maintenance sampling system. The analyzer is installed above a slurry flow surface and can deliver an accurate chemical analysis of production feed, concentrate product or tailings. All elements including light once can be measured simultaneously without manual sampling and sample preparation.
-
product
Portable Servo Conditioners
PTS-V
Bemco PTS-V Portable Servo Conditioners provide a closed loop flow of controlled temperature air or gas to an insulated enclosure or structure. Bemco high pressure gas servo conditioners provide air or gas at up to two atmospheres of pressure to heat exchangers and thermal shrouds. Bemco HPG High Pressure Gas Conditioners are described on a separate page.
-
product
Accelerated Stress Test Chamber
CSZ's accelerated stress test chambers combine mechanical refrigeration; LN2 cooling and high velocity air flow for fast product temperature change rates. Chambers are typically designed with a change rate up to 30C (54F) per minute based upon the part temperature. Common uses are production stress testing circuit boards, electronic drives, assemblies, etc. Design allows the user to quickly control and change the temperature of the product.
-
product
Software For Transformer Measuring Professional
T-Base Pro
T-Base Pro is a new powerful software for electrical testing, developed by Raytech GmbH. Years of experience in building world-class testing equipment flowed into the development, resulting in a state-of-the-art software framework. Its functionality ranges from simple data import and export using a USB stick, to the full control of the sophisticated Raytech testing devices and measurement systems remotely.
-
product
Multi Monitor
MD
It is a 30mm monitor with 2 screens and 3 colors that displays 1-5V analog signals converted into numerical values.Since various unit displays are possible, it is ideal for monitoring pressure sensors and flow rate sensors.
