Test Boards
See Also: Board Test, Testboards, DUT, Extender Boards
-
Product
Kelvin Test Contactor
nano
-
nano Kelvin™ test contactor is a well-established Cantilever Kelvin test contactor with proven performance in the automotive market and further increasing popularity due to the robustness and reliability of the product.Featuring a small imprint area, contact motion decoupled from the test board and simple and cost-efficient test boards.
-
Product
Generic Probe Cards, PIB's, and Loadboards
-
Test Spectrum can provide generic Probe Cards, Probe Interface Boards (PIB), and loadboards. Choose from existing configurations already designed, or a generic test board for your specific tester configuration can be designed quickly.Teradyne J750 Probe Card and PIB; Teradyne Integra Flex PIB; Teradyne Ultra Flex PIB; Teradyne Catalyst PIB; Credence Quartet PIB (Probe Interface Board); Advantest 93K 1024 PIB
-
Product
Meter Test Station
WECO 8000
-
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
Product
VME Test Extender 9U/220mm J1/J2/J0
111EXT9122-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Cardboard Puncture Tester
DRK104A
-
Shandong Drick Instruments Co., Ltd.
DRK104A cardboard puncture tester is used to test the corrugated board anti-pierced performance (puncture strength). It has the snap-operating handle, automatic reset and safety protection function. It is the indispensable instrument for carton manufacturing plants, research and quality supervision, inspection and other enterprises and departments.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Flying Probe Tester
FA1811
-
Designed specifically for package board testing, the FA1811 achieves both high-precision contact with a total probing precision of 10 μm, and a testing speed rivaling generic flying probe testers to meet ever increasing demands for greater analytical power, faster testing speeds and reduced costs.
-
Product
Development Boards
-
Advantech Development boards provide a schematic software & reference to reduce design effort at the development stage. Development Boards have been designed in order to allow customers to verify the functions of COM, text carrier board problems and support COM series. Advantech has designed a Development Board which can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
Product
Satellite ATE
MS 1123
-
Configurable Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out card level testing for satellite systems (12 different types of boards). The purpose of ATE is to provide a user-friendly environment to test the boards for their functionality, perform specific tests of each card. The card level testing facilitates troubleshooting down to a faulty signal flow path. Both hardware and software designed such a way that each Input / Output is configurable and user can dynamically script the test procedure using standard ‘C’ Language.
-
Product
VME Test Extender 6U/220mm 64X w/o P0
116EXT6122-012XR
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Clamshell Type Mechanical Fixtures
Series 71
-
The VP Series 71 dual well mechanical kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface and the advantage of testing two devices. This can be similar devices, or devices that are used together in a functional test. The VP Series 71 Kits have the same available features and options as the Series 70 Kit and are available with or without the ITA G12 Interface.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
ASA240
-
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Dual LGA3647-P0 Intel® Xeon® Scalable EATX Server Board with 24 DDR4, 5 PCIe x16 + 1 PCIe x8, 10 SATA3.0, 6 USB3.0, Dual 10GbE, IPMI
ASMB-935
-
- EATX server board with dual Xeon Scalable processors- DDR4 2933 MHz RDIMM up to 3TB, support Intel Optane DC Persistent Memory- Five PCIe x16 (Gen3) and one PCIe x8 (Gen3) for three double-deck cards- Intel® X557-AT2 dual 10GbE ports- Ten SATA3.0 and six USB3.0 ports- One M.2 2280 (SATA / PCIe compatible)- 0 ~ 40 °C ambient operating temperature range
-
Product
2U OTII-Compliant Edge Server
SKY-7223D
-
2U OTII-compliant edge server with dual 2nd Gen Intel® Xeon® CPUs and QAT/DPDK support. A short-depth, high-expansion platform for 5G vRAN/MEC.
-
Product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
-
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
Product
DIN Rail, 160-Pin DIN41612 Breakout
40-967-160-F
-
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
Product
Automotive Test Solutions
-
The testing and simulation systems from this division are used primarily in the automotive and automotive supplier industry. These are, for example, modular function-testing systems and diagnostic tools for automotive ECUs or bus communication systems for a wide variety of electronic components in automotive production. Electromechanical assemblies and entire car seats are also tested to ensure they function
-
Product
M/MA Module Carrier
VX405C
-
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
-
Product
Distribution Board, For 8 N181x SPDT Switches
Y1150A / 34945EXT
-
Connects the 34945EXT to 8 N181x SPDT to route the power and control signals from the driver module to the switches
-
Product
LGA 1700 Intel® 12th Gen. Core™ MicroATX Server Board with 4 x DDR5, 3 x PCIe (1 x Gen 5, 2 x Gen 4), 6 x USB 3.2, 5 x SATA3, Quad/Dual LANs, and IPMI
ASMB-588
-
- LGA 1700 Intel® 12th Gen. Core™ i9/i7/i5/i3 processors with W680 chipset- DDR5 ECC/Non-ECC 4400/4000/3600 MHz UDIMM up to 128 GB- One PCIe x16 (Gen 5) and two PCIe x4 (Gen 4) slots- Triple displays - DVI-D, VGA, and HDMI 2.0 ports- Five SATA 3 ports and six USB 3.2 ports- One M.2 2280 (PCIe x4)- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C (32 ~ 140 °F) ambient operating temperature range
-
Product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
-
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
Product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
-
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
-
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
-
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
-
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
Semiconductors Testing
-
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
