Filter Results By:
Products
Applications
Manufacturers
-
product
Miniature Concentric Ring Set
PRF-912B
- Measures Surface Resistance from 0.9Ω to 1.0x1012Ω- Approximates Measurements Typically Obtained when using ANSI/ESD STM11.11- Spacing Allows for Measurement Area of 0.32 inches (8.13mm)- Spring Loaded Center Electrode Surrounded by 10 Contact Electrodes- Includes Conductive Rubber Covers- Certificate of Calibration Traceable to NIST included
-
product
Kelvin Probe Set
11059A
Reduce ground-related errors and contact resistance through gold-plated flat tweezers and special gripping surfaces
-
product
KV CAPS
200 V
Macom Technology Solutions Holdings Inc.
The MACOM KV CAPSTM Si high voltage capacitors feature very high working voltage ratings, very low loss and excellent stability by virtue of their novel internal construction and very high-quality dielectric layers. These capacitors are available as unpackaged chips. The chips have gold bonding surfaces on both terminals to enable excellent bonding and minimum contact resistance.
-
-
product
Optical 12,000 Meter Connector
Teledyne Impulse-PDM’s 5135/5175 optical connectors utilize proven standard ferrule technology and are available for multi-mode or single-mode operation.The connectors are manufactured in Titanium Ti 6Al-4V, which is electro-polished to remove surface contamination, thus improving resistance to corrosion. The engaging nuts are also manufactured in the same grade of Titanium and the threads are coated with a Nickel/PTFE composite coating to prevent galling. The connectors have been qualifi ed to 12,000 meter operating depth.
-
product
Digital Megohmmeter
800
The ACL 800 Digital Megohmmeter is a dependable and easy-to-use audit kit that is designed to test static dissipative surfaces for electrical resistivity and resistance according to industry standards such as ANSI/ESD test methods S4.1, S7.1, and ASTM D257. Tests are easy to perform with or without the 5lb probes. Use optional concentric ring probe for conformance to STM11.11.
-
product
Manual Clemen Unit
Elcometer 3000
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-20
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-20GHz
-
product
Zero-distance Drop Test System
KRD40 series
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
-
product
Franklin Tester
Model 717
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
product
Probe Card PCB's
DTS offers both generic and custom PCBs blanks for probe cards. Probe card PCBs are available for all tester platforms and can be configured for any vertical technology, epoxy cantilever and legacy blade cards. DTS probe card blanks are made to precise specifications required for all probing technologies and are available in high speed and high temperature materials. All probe card PCBs employ a balanced layering construction to maintain tight flatness specifications and minimize warping, allowing good probe planarity. Gold plating on all surface metals facilitates easy soldering and minimizes probe resistance. DTS is continually adding new probe card blanks to its library!
-
product
Surface Resistance System Kit
PRS-801RM
- Perform Point-to-Point and Resistance to Ground Measurements from 0.01 Ω to 200 Teraohms- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Measures in accordance with ESD TR53, ANSI/ESD S4.1, ANSI/ESD S7.1, ANSI/ESD STM97.1 and others- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Operates using a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- Stores up to 999 Test Values Into Memory- Compatible with Prostat Connect 2.0 for Downloading into Excel®- Charging and Download via Standard Micro USB Cable- Includes 5lb Conductive Probes and Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
product
Surface Resistance Meter
SRMETER2
The Surface Resistance Meter is a wide range, multi-scale, auto-ranging meter. This meter is appropriate for auditing static control work surfaces.The meter is 9V battery powered and simple to use.NIST Calibrated
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-30
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-30GHz
-
product
Bench Hardness Tester
MTR X-SERIES
The bench hardness tester MTR X-SERIES operates to determination through the measurement of electrical resistance. The MTR X-SERIES hardness tester has been designed to solve some of the still unsolved issues in the field of hardness control. Its test principle allows the user to perform measurements in difficult or inaccessible points internal surfaces and gear teeth.
-
product
Slip Testing (Articulated Strut) (Mark II)
SG-P07MII
It's used to determine the slip resistance of footwear sole, heel or related materials against planar walkway surface or walkway surrogates under dry, wet or contaminated conditions.
-
product
Capacitors - Beam Lead
Macom Technology Solutions Holdings Inc.
MACOM’s MMI-9000 and 9100 Series Chip Capacitors feature high stand-off voltage and low dielectric loss leveraging nitride/oxide dielectric layers. Gold bonding surfaces, top and bottom provide ease of bonding and minimum contact resistance. MACOMs beam lead capacitors have high insulation resistance, low dissipation factor, and low temperature coefficient, which are features that produce devices with excellent long-term stability.
-
product
Hardness Tester
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Hardness testing is measuring a material's resistance to permanent deformation at its surface
-
product
Laboratory Salt Fog And Salt Spray Corrosion Aging Test Equipment
Shenzhen Chuangxin Instruments Co., Ltd.
Corrosion Salt Spray Fog Environmental Test Machine for Nss / Acss / Cass Test is used to test the anti-erosion quality of the surface of all materials after the rust-proof of painting, coating, electroplating, anoding and rust-proof of greasing.anti corrosion treatment for a variety of materials, corrosion resistance of their products.
-
product
Coatings Inspection Division
For over seventy years, Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings industry. Whether you are measuring surface profile, surface cleanliness, dry film thickness, porosity, adhesion or gloss; or testing the abrasion, scratch resistance or elasticity of a coating - Elcometer's extensive and versatile range of equipment provides the complete solution to your coatings inspection requirements, whatever and wherever they might be.
-
product
Surface Resistance Meter Kit - Test Anti-Static, Static Dissipative and Conductive Surfaces
PRS-812RM
- Surface Resistance Tester from 0.10 Ω to 1 Teraohm- Constant Voltages 10 volts and 100 volts- Automatic Electrification Period- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and resistance to ground (Rtg)- Measures resistance of ESD Flooring, ESD Worksurfaces and Packaging- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Surface Resistance Probes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
Digital Surface Resistance Meter
NEW Enclosure with Rubber Grip EdgesThinner and narrower design is easier to hold and provides protection from drops.NEW Quick Check ButtonBypasses the 15 second electrification period to allow quick spot checks.NEW Battery Compartment
-
product
Handheld LCR Meter
Smart Tweezers®
Smart Tweezers® are a hand held LCR meter that provides users with a simplified method of identifying and evaluation Surface Mount Devices and troubleshooting complex electronic systems. The unique deign combines a set of precision gold-plated tweezers and a powerful, yet small, digital LCR-meter in a lightweight device. Powered by a Li-Ion battery, Smart Tweezers® can identify the type of component and measure for Inductance, Resistance, Capacitance and ESR values with no set-up.
-
product
Surface Resistance Meter
WL MIDGET
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
product
ESD LCD SURFACE RESISTIVITY METER (WITH 1 PAIR OF 5 POUND ELECTRODES)
The ESD LCD SURFACE RESISTIVITY METER provides everything necessary to test work surfaces using the procedure outlined in the EOS/ESD-S4.1 standard. This test kit makes testing surface resistance easy – simply place the weights attach the cables, switch to the correct voltage and press the button to read resistance directly on the meter. The meter incorporates parallel probes on the bottom of the unit which allows the user to make surface resistivity measurements. The parallel probes allow for quick and easy testing of a variety of surfaces and materials, without the use of the five pound electrodes
-
product
Portable Static Grounding Kit
Grounding Kit
The portable grounding kit combines multiple shortened grounding rods with surface wire grounding techniques to provide acceptably low resistance for static grounding requirements in field operations.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-14
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-14GHz
-
product
Resistivity Meters
Precisely Measure Surface Resistivity, Volume Resistivity, or Resistance to Ground. Advanced Energy's Trek and Monroe resistivity meters offer accurate and repeatable measurements for surface resistivity, volume resistivity, or resistance to the ground.
-
product
Power Metering Precision Shunt Resistore
PMS
These components have E-Beam welded manganese-copper alloy elements giving high strength, stability and reliability. Low thermal EMF and TCR. Small size and minimal power loss. Minimal heat generation and surface temperature due to small total resistance. Proprietary processing technique allows very low resistance values. Ideally suited for KWh meters and sampling sensor shunts. These units are also suitable for custom design.
