Limiters
-
Product
IR FPA sensors
-
IR FPA sensors are the most important modules of thermal imagers. Design of sensor electronics (camera core) is a crucial part of designing of new thermal imager. Knowledge of precise parameters of IR FPA sensor is needed by both professionals involved in both IR FPA technology/thermal imagers technology because parameters of IR FPA sensors determine performance limits of thermal imagers. Therefore test equipment that enable measurement of IR FPA sensors is a vital tool for development of both IR FPA technology/thermal imagers technology. It is commonly known that data sheets provided by manufacturers of IR FPA sensors (both cooled or non-cooled) provide too little details for electronics designers. Sometimes the provided data is not accurate enough and better sensor performance can be achieved using modified control signals. Therefore design teams loose sometimes years to develop electronic camera core optimized for a specific IR FPA sensor. When the type of the IR FPA sensor is changed the whole process is to be repeated. In this situation an universal, flexible camera core that would accept IR FPA sensors from different manufacturers and to carry out semi-automatic determination of optimal signal controls for a specific IR FPA sensor would be highly desirable.
-
Product
High-Speed A/D 12-Bit Digitizers
Digitizer
GaGe 12-bit resolution digitizer models divide the input voltage range into 4,096 different digitization levels, which improves the delectability limit by a factor of 16 over the 256 levels of an 8-bit resolution digitizer model.
-
Product
Digital SINE Controller
DVC-4/8 SINE
-
RANGE: 2 to 6250 Hz, digitally synthesized.STABILITY: +/- 100ppm/C, crystal-controlled.DISTORTION: <0.50% thd 0.25% typical.LIMITS: Sweeps between programmed upper and lower limits.
-
Product
Nano Spotter For MALDI-TOF MS
AccuSpot
-
Bringing LC to MALDI Technology LC/MS/MS is often regarded as the technique of choice in identifying components from complex mixtures; however, it is not without its limitations. An alternative approach is to consider LC/MALDI.
-
Product
DL379BCOMBO w/ ATTPC3 and Dual NCV
DL379BCOMBO
-
UEi Test & Measurement Instruments
The DL379BCOMBO HVAC/R Clamp Meter with a CATIV 300V rating, dual level NCV, dual display and a 3-Year limited warranty is a very user friendly clamp meter. The detachable clamp head makes it entirely versatile and the meter for a tech to have in his, or her, tool box. And is combined with the ATTPC3 Pipe Clamp Adapter.
-
Product
Swivel Joints
-
The Swivel Joint is a special type of RF waveguide joint. It is a joint that is limited in rotation angle, compact in size, with low mechanical torque and high peak power capacity.
-
Product
Single-Phase Static Switches
ISSF COMPACT
-
ISSF 'COMPACT' series circuit breakers are electrical devices used to interrupt or connect the flow of current in an electrical circuit. They are designed to provide high reliability and protection in a compact size. They overcome the limitations of electromechanical switches in many difficult and demanding applications, such as the control of high-power motors, transformers, tungsten lamps, heating elements, and electric ovens.
-
Product
Cleaning Validation
-
Cleaning validation, which is essential for quality assurance in pharmaceutical manufacturing, refers to the quantification of residues after cleaning of manufacturing facilities and equipment to verify that the amount is below a predetermined acceptable limit.
-
Product
Field Test Kit
621
-
TESCO’s light-weight, 50 Amp Field Meter Test Kit (Catalog No. 621) with Power Factor, has been designed to reduce the weight of field test equipment to the lowest possible limit. The carrying case is fabricated from durable powder coated aluminum. The total weight of the meter test kit including leads, and digital reference standard is only 25 lbs! The test kit also incorporates ample storage space for the cable set.
-
Product
Total Nitrogen Unit For TOC-L Series
TNM-L
-
Perform simultaneous TOC and TN measurements. *720 °C catalytic thermal decomposition/chemiluminescence methods are adopted for TN measurement. There is no interference from metallic ions or bromine in sea water.*Measurements over a wide range with a detection limit of 5 μg/L for TOC-LCH to an upper limit of 10,000 mg/L.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
PCI Smart Bus Extenders
PCIEXT-64 - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
Precision Microcontrollers
-
Analog Devices provides a range of analog microcontrollers featuring ARM® Cortex™-M3 processors that help enable this product portfolio’s high precision, high performance, and low cost. By featuring ARM Cortex-M3 processors, our devices include a rich support system to aid product development throughout applications that include optical networking, industrial control, point-of-care diagnostics, and a variety of other industrial, instrumentation, and medical uses. Precision analog blocks including, but not limited to ADCs, DACs and references allow for precision control and measurements. Included also is the ability to read back diagnostics, which is a key requirement in the above applications.
-
Product
Photoelectric Switch
PE3
-
● Compact size for 13.5(W)*25.5(H)*32.0(L)● A wealth of models ideal for limit control, counting control, and other applications.● Sensing distance of 5~60cm for Diffuse reflective models, 1M~2M for Retro reflective models and 1M~5M for Through beam models.
-
Product
47~862MHz FTTH Digital TV Two Output Low Optical Receiver
H9222L
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9222L, operating bandwidth of 47 ~ 862MHz, is a suitable digital television FTTH applications, ultra-low optical receiver, Whether used in analog television or digital television. Receiving at high optical power can be adjusted by PAD level, played limiting output, so H9222L within a large dynamic range of the received optical power of +2 dBm ~-20dBm, have excellent characteristics.
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
IO-Link
-
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and communications interface, as well as the IO-Link transceivers featuring Integrated Step-Down Regulators and LDO with ±60V cable interface protection provide the required ruggedness. Optimum EMC performance is achieved with adjustable current limit and slew rate transmitters. Automatic wake-up request (WURQ) generation and an output supply current boosting capability for device startup are also available. Additional components integrate a 300 mA step-down (buck) regulator and a 150 mA LDO to supply all the power required for internal electronics in an connected sensor or actuator.
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 3 Output, 0 V, 30 V, 0 A, 3 A
72-6628
-
The 72-6628 is a Triple Bench Power Supply with adjustable current control and galvanized steel case. The DC regulated power supply is a completely solid state, compact, well regulated, constant voltage power supply suitable for service field, hobby, laboratory and testing use. It provides three different voltages output for different. Overload and short-circuit protection, prevent the unit from overload and short circuit. When the unit is under the condition of overload or short circuit, the output current will be limited. Independent 5V, 12V easy snap-on output terminals to make it easy to use for TTL and CMOS circuit testing. The grounding of the output terminals is independent that the output can be connected in series to make a higher output voltage.
-
Product
CORROSION GAUGE
MMX-7
-
The MMX-7 has all features of the MX & MMX gauges with some additional features and advantages. Selectable Large Digits and B-Scan display options. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and selectable low, medium or high gain options. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVX/PVXview or Java-based PC software makes this thing a complete kit and then some! 2-year limited warranty.
-
Product
Cover Extend Feature, GTE 10.00p
K8217B
-
Cover-Extend Technology (CET) extends the measurement capability of VTEP or nanoVTEP into powered testing by using the Boundary Scan output cell to test the connectors and socket signal pins. This capability extends the Boundary Scan limited access solution on non-boundary scan devices with the use of VTEP or nanoVTEP and CET signal conditioner card hardware.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Battery Discharge and Capacity Testers
-
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
Product
Signal Splitters
-
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
Product
1GHz EMC Emissions Analyser
SA1002
-
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
Product
Serial Bus Buffers, Extenders, and Accelerators
-
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
Product
ATCA CO2 AC-DC 2 Slot 3U
-
The AdvancedTCA® CO2, 2-slot chassis, AC-DC version allows to build a dedicated application in a very limited rack space.
-
Product
PXI High Density MUX BRIC, 32-Chan, 10-Pole
40-570-412
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
5KV Withstanding Voltage Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
The CX2672C is a high-precision testing device with upper limited alarm function for withstand voltage test. And it's is strictly designed according to the related IEC standard. The voltage, current and timing are with digital display function. The testing is quick and high accuracy which is not only applied in the production line but also in the lab. It's a neccessary tester for electric safety test of electrical equipment.
-
Product
Digital Panel Meter
MPF-5A
-
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth
-
Product
Diode Tester
FEC VF40CM
-
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
