Leakage
-
Product
Precision DC Power Module, 50V, 3A, 100W
N6762A
Power Module
The Keysight N6762A is a 100 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. For leakage current or sleep-mode current measurements, add option 2UA for measurement capability down to 1 μA.
-
Product
AC/DC Clamp Milliammeter (CE)
M-740
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current*Suitable for measurement of 4-20mA DC controlled circuit*DC mV analog signal output*Lowest influence from Magnetization and Terrestrial magnetism*Wide measuring ranges - up to DC 1000mA and AC10A
-
Product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
-
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
-
Product
200KHz AUTOMATIC TRANSFORMER TEST SYSTEM
VE2729XAU
-
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
Product
Clamp type AC Current Sensor/for Low Leakage Current Measurements(ZCT Series)
ALCL-40D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for micro ampere current measurements.*Super high accurate sprit type ZCT sensor.*High sensitivity and least affection from external magnetic field. (less than 10μA for 400A nearby conductor)*For leakage current measurements of arrester.*Stable measurements under high electric field and strong magnetic field.
-
Product
Leakage Current Clamp Tester with Bluetooth
M-1141XR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
Product
3W to 10W - Single Output / Multiple Output
PXC-M Series
-
*Industry Standard DIP-24 Package*9-36 Vdc, 18-75 Vdc Inputs*3.3, 5, 12, 15, 24, ±5, ±12, ±15 Vdc Outputs*5 kVAC Isolation (2 x MOPP)*IEC/EN60601-1, ES60601-1, CE Mark*Low Off-Load Power Draw*2.5µA Leakage Current
-
Product
Million Meg Ohm Meter
Model HIR 603
-
Laxtronics Instruments & Controls Pvt. Ltd
100 Kilo Ohm To 100 Tera ohms, Leakage Current 10 Milli Ampere To 1 Nano Ampere, Test Voltage 10 Volts DC To 1000 Volts.
-
Product
High Voltage Power Source
PM1000
-
The PM1000 is a high voltage power source capable of supplying up to 1000 V/20 mA to a load. It is intended for use in measuring leakage and breakdown voltages of devices. There are five voltage ranges and five current ranges.
-
Product
Electronics Failure Analysis System
Sentris
-
Due to the continued decrease in integrated circuit feature size and supply voltages, detecting and locating the miniscule amount of heat generated by failure sites has become increasingly difficult. Sentris pinpoints low-level infrared thermal emissions from IC faults such as short circuits and leakage current.
-
Product
Clamp on AC Leakage Current Sensors
-
High Accuracy Clamp AC Leakage Sensor use permalloy magnetic cores, with small size, high accuracy, good stability, strong anti-interference ability characteristics. It is applied with double shield technology, which insure strong anti-interference ability.
-
Product
Mini AC Leakage Current Clamp Tester
M-100+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・18mmφCT window and ultra compact size.・Least affection from the external magnetic field.・The special alloy is used for core material that resists the rust over long period of use and ensures stable,high accurate measurements with very slight influence from aging.
-
Product
PXIe Short SMU
52403P
Source Measure Unit
Chroma's 52403P is a PXI Express Short Pulse SMU (Source/Measure Unit) designed for fast, precise and reliable sourcing and measurement of thermo-sensitive devices such as high-power laser diodes (LD). Integrating a high-speed pulser, a high precision SMU and a DAQ module into a single PXIe SMU, the 52403P can measure both the LIV and the low-level leakage current of a high-power LDs.
-
Product
Precision DC Power Module, 50V, 1.5A, 50W
N6761A
Power Module
The Keysight N6761A is a 50 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. For leakage current or sleep-mode current measurements, add option 2UA for measurement capability down to 1 μA.
-
Product
High Voltage Test System
CKT-1180
-
The CKT 1180 is a High-Voltage Test System with up to 3500 VDC and 2800 VAC RMS leakage test capabilities.Originally designed for High-Speed Rail, the CKT 1180’s focus is to test assemblies that require extremely high reliability and work at elevated voltages.
-
Product
1kV DC Hipot Tester For Capacitor
-
AllWin Instrument Science and Technology Co., Ltd.
The max capacitor up to 50uFcharge time is 0~5s; test time is 1~99s( continue set)The max leakage current can up to 300mA
-
Product
Electrical Safety Test Solutions
-
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
Product
Cylinder Leakage Testers
EEPV509
-
Input pressure gauge displays input air pressure for proper cylinder leakage test set up and accurate results Pressure gauge range is 0-100 psi (0-700 kPa) in 2 psi (20 kPa) increments Cylinder leakage gauge displays leakage as a percentage of input pressure with 3 distinctive zones of high, moderate and low
-
Product
Thermalyze Extension for Steady State Analysis
Lock-In
-
Steady-state thermography is limited to detecting hot spots that heat up a minimum of 100 mK (0.100°C). This may be useful for locating shorts on high-power devices, but is inadequate for detecting low power defects such as semiconductor device leakage current or short circuit with very low or very high resistance. Steady-state thermography also suffers from poor spatial resolution as the heat from localized hot spots diffuses rapidly, blurring the location of the heat source.
-
Product
High Voltage Power Source
PM2000
-
The PM2000 is a high voltage power source capable of supplying up to 2000 V and sourcing 10mA to a load. The high potential at 2 kV fulfills coverage for mostly all semiconductor devices where leakage and breakdown measurements are involved. The module has been incorporated with interlock feature to ensure safety.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
Current Transformers
-
Rishabh Instruments Pvt. Ltd.,
Rish Nano CT is a very reliable, efficient and robust current transformer for measurement of AC current. It provides 100 mA AC output. It can be used in Circuit breakers. Earth Leakage Protection.
-
Product
Iron Core Earth Tester
-
Weshine Electric Manufacturing Co., Ltd
Transformer iron core grounding current tester is a high-precision clamp meter specially designed for measuring AC leakage current, current and voltage. Large diameter (80×80mm) can clamp φ80mm cable, or 96mm×4mm flat steel ground wire, suitable for cables Leakage detection and transformer grounding flat steel leakage measurement.
-
Product
HMM+™ Tester
Model 4702
-
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
AC Leakage Clamp Meter
SK-7820/SK-7825
-
Wide range from 40mA to 100A AC,Conductor dia. : φ24mm max (SK-7820), φ40mm max (SK-7825)AC voltage measurement.Vibration alert comparator.(The function to show the comparator result by buzzer and vibration which is convenient innoisy surroundings.)
-
Product
High Voltage Snubber Capacitor
STP-01RAN/STP-01RFN/STP-01RFB
-
This series of capacitors is Plastic Enclosure, Dry construction design and doesn't have leakage problem when compared with traditional Metal Enclosure Oil impregnated capacitors.Handle Medium Frequency range, high surge current, RMS current and surge voltage with temperature up to +105CCapacitance : 0.1uF - 15uF ( can be customized )Voltage range : 1,200Vdc to 17,000Vdc / 350Vrms to 6,900VrmsRMS Current - Irms : up to 100Armspeak to peak pulse current - Ipp : up to 5,900AppTemperature ranges : +85C / +105C
-
Product
Insulation Resistance Measuring Equipment
AMIC-5010
-
Insulation resistance measurement - 15TΩ: * 50 - 1000 V, in 10 V steps, * 1000 - 5000 V, in 25 V steps ; Memory of 999 results and transmission to PC ; Measurement of AC and DC voltage and capacity ; Measurement of leakage current and function with digital filter ; Measurement of continuity of protection and equipotential connections ; Adjustable alarm limits
-
Product
Low Thermal Guarded Scanner
160B Opt. 5 & 320B Opt. 5
-
Data Proof’s Low Thermal Guarded Scanners are designed to improve accuracy in high resistance measurements. Unguarded, the Data Proof scanners have leakages of about 1.5 x 1012 Ω which can cause errors of a few tenths of a ppm when measuring 1 MΩ. Guarding reduces the errors allowing excellent accuracy up to the 1 GΩ level.





























