Humidity
-
Product
Calibration Services
-
for Humidity, Dew Point, Trace Moisture and Temperature Measurement Instruments
-
Product
Hygro-Thermometer
-
Terra's hygro-thermometer offers simultaneous display of temperature and humidity in a large LCD readout (80mm x 62mm).
-
Product
CO2 Concentration Transmitter
H5324
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
-
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
Product
Temperature Humidity Meters
-
Measure and record temperature and humidity readings anywhere.
-
Product
Web Sensor
T3510
-
Web Sensor with built-in relative humidity and temperature sensors. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Coating Thickness Gauge
NOVOTEST TP-1M
-
Portable Coating Thickness Gauge NOVOTEST TP-1M – device for operative non-destructive measuring of coating thickness in compliance with ISO 2808 with high measurement accuracy.Coating thickness gauge is designed to test:thickness of various thick protective coatings on various metals and alloys;thickness of paint and other dielectrics – radioabsorbing, mastic, teflon, plastic, electroplating coatings on steel;thickness of electroplating and paint coatings on non-ferromagnetic alloys and non-ferrous metals;thickness of bitumen and other thick coatings on various metals and alloys;as well as relative humidity, air temperature, surface temperature, dew point temperature and difference between surface and dew point temperatures, estimate the depth of grooves and the surface roughnessElectronic thickness gauge – device which widely used in shipbuilding and automotive industries for measuring of the thickness of paint, in order to test the quality of products, also it used for determining technical condition of the tested objects.
-
Product
Wood Moisture Meters
-
PeakTech Prüf- und Messtechnik GmbH
High quality wood and material moisture meter, which is characterized by its ease of use and universal applicability. The device has an LCD display, in which measured values of humidity and ambient temperature are displayed. In addition, it is equipped with an LED display, which enables a quick good-bad assessment of the measured values. When burning wood in a wood-burning stove with a high moisture content, the efficiency of the stove decreases, while at the same time the emission of pollutants, such as soot and fine dust, increases. In addition, there is a build-up of soot in the chimney, which can lead to a fire. Therefore, this device is ideal for wood storage, control during the heating season or use in construction.
-
Product
Thermo-Hygrometer
D3121-4
-
Thermometer, hygrometer is designed for measurement and datalogging of temperature, relative humidity into the internal non-volatile memory.
-
Product
Hygrometers
-
Temperature and humidity are key factors in maintaining optimal comfort levels and good indoor air quality. Quickly and conveniently take accurate humidity and temperature readings with Sper Scientific line of humidity meters.
-
Product
Temperature/ Humidity Meters
-
The Temperature /Humidity Meter has a highly accurate sensor chip to measure relative humidity and temperature. It is perfect for many industrial applications, laboratory and other types of work locations.
-
Product
SS Body Vacuum Switch (longbody, NEMA 4)
P117LV
-
The P117LV NEMA 4 Stainless Steel Vacuum Switches are the weather-proof, liquid-resistant version of the P117V. The NEMA 4 rating makes these rugged switches suitable for outside applications or in areas of condensing humidity. Unlike the P117V, the P117LV set point is factory set to customer specification and is non-adjustable.
-
Product
Sweating Thermal Guarded Hotplate
-
Sataton Instruments Technology CO., Ltd
Sweating guarded hotplate is the textile testing instrument for measuring of thermal and water-vapour resistance properties under steady-state conditions. By testing the thermal resistance and water-vapour resistance of textile materials, the tester provides a direct data for characterizing the textiles’ physiological comfort which involve a complex combination of heat and mass transfer. The hotplate is intended to simulate the heat and mass transfer processes which occur next to human skin and measure the hence transport properties in a steady-state conditions involving combinations of temperature relative humidity, air speed, and in liquid or gaseous phase.
-
Product
Transducers with 0-10 Volts Output
-
Overview of transducers with 0-10V output for temperature, humidity, CO2 and pressure.
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x1
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1×1 fiber optic switch -Features·Low Insertion Loss·High Stability, High Reliability·Low Crosstalk·Wide Wavelength Range·Epoxy-free on Optical Path·Latching and Non-latchingGLSUN 1×1 fiber optic switch -Applications·System Monitoring·OADM·R&D in Laboratory·MAN (Metropolitan Area Network)·Network Security and MonitoringGLSUN 1×1 fiber optic switch - SpecificationsParameters Unit SUN-FSW-1×1Wavelength Range nm 850±40 / 1300±40 1260 ~ 1650Test Wavelength nm 850 / 1300 1310 / 1550Insertion Loss 1,2 dB Typ: 0.5 Max: 0.8 Typ: 0.4 Max: 0.6Return Loss 1, 2 dB MM ≥ 30 SM ≥ 50Crosstalk 1 dB MM ≥ 65 SM ≥ 70PDL dB ≤0.05WDL dB ≤0.25Repeatability dB ≤±0.02Operating Voltage V 3.0 or 5.0Durability Cycles ≥ 10 MillionSwitching Time ms ≤8Optical Power mW ≤500Operating Temperature ℃ -20 ~ +70Storage Temperature ℃ -40 ~ +85Relative Humidity % 5 ~ 95Weight g 14Dimension mm (L)27.0×(W)12.6×(H)8.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
Temperature and Humidity Transmitter
T3319-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
Industrial Serial GSM Modem
ENVIROMUX-GSM-IND
-
Sends SMS messages to a pager or cell phone when a sensor goes out of range of a configurable threshold. SIM card supporting SMS messaging required (not included). Ideal for harsh environments and high temperatures up to 149°F (65°C). GSM/GPRS/EDGE 850/900/1800/1900 MHz. AT command compatible. Dimensions: 3.58x2.28x0.87 in (91x58x22 mm). Operating temperature: -13 to 149°F (-25 to 65°C). Operating humidity: up to 95% non-condensing RH. Regulatory approvals: CE, C-Tick. Compatible with ENVIROMUX-SEMS-16(U).
-
Product
Temperature & Humidity Testers
-
UEi Test & Measurement Instruments
Temperature & Humidity Testers
-
Product
Climatic Chamber
PAC series
-
The PAC series of climatic chambers are a great choice for cyclic low, high temperature and humidity tests. Built with the highest quality and reliability, this chamber is capable of meeting the most stringent testing needs of various international standards such as ASTM, IEC, MIL, DIN, etc.
-
Product
Mini Temperature and Humidity Meter
PTHM15
-
Auto Power OffFast Response TimeDew Point TemperatureDual Display Temperature & HumidityData Hold FunctionHumidity Range: 0-100%RHTemperature Range: -20 - 80 C / -4 - 176 FDew Point Temperature: -20 - 80 C / -4 - 176 FWet Bulb Temperature: 0- 80 C / 32 - 176 FHumidity Accuracy: +/- 3% RHAir Temperature Accuracy: +/- 0.5 C @ 25 CResolution: 0.01% RH, 0.01 C/FResponse Time: %RH: 105 (90% at +25C still air)Battery Type: 9V (Included)Operating Temperature: 32 F to 104 F, <80% RHStorage Temperature: 14F to 140 F, <80% RHDimensions: 6.89' H x 2.28' W x 1.38' DWeight: 5.04 oz.Sold as : Unit
-
Product
Thermometer Hygrometer Data Logger
S3120E
-
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
-
Product
Handheld Thermo Hygrometer
HD2101.1
-
Portable thermo hygrometer, measuring range for temperature -200 °C…650 °C with probes TP47… , for humidity 0…100%RH.
-
Product
Altitude Chambers
-
Our Altitude Chambers combine temperature and altitude with optional humidity to test basic components or subassemblies designed for use in a variety of industries. With a CSZ altitude chambers, you can control the temperature environment for testing while simulating various altitudes from site level to 65,000 feet (42 Torr). Altitude testing may be continued without temperature control up to 200,000 feet (.169 Torr). This same chamber may also be used as a temperature/humidity cycling chamber at site level only.
-
Product
Portable,Temp.,Humidity,Dew Point Meter
HT-315
-
Resolution: 0.01% RH, 0.01 degreeMx, MIn measurmentRS 232 PC interfaceResponse Time 5 to 30 seconds typicallyRange 0 to 80 ,32 to 176 . 10 % to 95 % R.HDEW pont.Range -25.3 to 48.9
-
Product
Wireless Transmitters
-
Omega wireless transmitters are weather-resistant and are designed to deliver a wide range of data such as voltage, current, temperature, humidity, barometric pressure, and pH.
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Data Logger
MS55D
-
The complete solution for monitoring of temperature, humidity and other values.
-
Product
Water Activity Meter
LD-LWTM-A10
-
Water Activity MeterLD-LWTM-A10is a real portable water activity meter, with a weight of only 1.5 kg, lighter than a mobile phone. It has 0 to 1.0 aw range and offers operating temperature range from 0 to 50˚C. Designed with 6 bit backlight LCD digital display and integrated nonconductive humidity sensor. It measures fast activity of water within 5 minutes and under-voltage alarm indication function. It is easy to measure water activity anytime and anywhere also used in free water in the state of food balance.
-
Product
Air Humidity Meter
-
Since air humidity is an important factor in many sectors including but not limited to manufacturing, agriculture, construction, restoration, remediation and heating, ventilation and air conditioning (HVAC), PCE also carries a number of air humidity meter devices designed for specific applications such as evaluating heat stress risk in hot work environments like boiler rooms, factories, construction sites and commercial bakeries. To accurately assess heat stress risk, an air humidity meter capable of detecting and classifying temperature in relation to the amount of moisture content in the air is recommended. The global standard description for heat stress is the Wet Bulb Globe Temperature Index (WBGT).
