Solid State Drives
memory storage without any moving parts.
-
Product
Solid State Current Injector
J2111A
-
The current injector is one of the most versatile of the injector products. Coupled with the G5100A, or other equivalent function generator, it is capable of performing small signal load steps up to 40MHz, with very fast rising and falling edges. Using the G5100A, also allows the rise and fall times to be controlled, various waveforms or even arbitrary waveforms. This can be used to simulate the effects of many different types of loads, including high speed digital circuit loading, which is often largely dynamic.
-
Product
PXI Solid State Versatile Multiplexer
40-682-002
-
This versatile solid state multiplexer is especially useful where a high density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future. The PXI multiplexer uses high performance solid state switching to ensure a service life of greater than 10 years and fast operation.
-
Product
PXI Solid State Very High Density Matrix
40-501-001
-
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
Product
PXI Versatile Multiplexer, Solid State, 250mA, 40V
40-682A-002
-
The 40-682A-002 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 250mA current and 40V voltage handling. The 40-682A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
Solid State Switch, 45 MHz to 50 GHz, SP4T
85332B
-
The Keysight 85332B single-pole-four-throw (SP4T) solid state switch maximizes your frequency range from 45 MHz up to 50 GHz, offering excellent performance with high isolation and fast switching speed.
-
Product
PXI Solid State Matrix Module, 8x2, 30 A
40-555B-011
-
The 40-555B-011 is a high current 8x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 10 A
40-666B-012
-
The 40-666B-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
-
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Solid State GaN (Gallium Nitride) Amplifiers
-
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
Product
Single 24-Channel 2-Pole 5 Amp PXI Solid State Multiplexer
40-652-003
-
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A
40-667C-012
-
The 40-667C-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Drives & Controllers
-
Most popular, Works with all McPherson SpectrometersDrive of Choice for high precision wavelength control settingUp to 50,000 steps per revolutionComputer control, RS232 (provided with USB adapter)Maintains all manual monochromator controlAvailable with fit kits to upgrade older instruments
-
Product
Solid State Relay
5200
-
The B/W 5200 Series solid state relays are offered in two basic types for use in a wide range of low and high sensitivity applications.Both 5200 solid state relays are designed to operate on either 115 or 230 volts AC at 50/60 hertz.Both models incorporate a low voltage sensing circuit.Furhtermore, both solid state relays are capable of performing control functions directly from electrodes suspended in a well or tank, the B/W Unifloat level sensing system, or various pilot devices such as pressure, flow and limit switches, thermostats and push buttons.
-
Product
PXI Solid State MUX, 1 bank, 160 channel
40-680-006
-
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Rackmount or compact airborne state of the art Solid State Power Amplifiers
SSPAs
-
Broadband off the shelf or custom designed RF/Microwave SSPAs as airborne baseplate miniature modules or as 19" 3U compact rackmount AC units, CW or Pulsed operation from 100W to 1KW up to Ku frequency band.
-
Product
SATA Drive Carrier
SD1-DISCO
-
The SD1-DISCO is a peripheral slot card for CompactPCI® Serial systems. The board accommodates a 2.5-inch size SATA drive, controlled by the SATA channel derived from the backplane connector P1.
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
PXI 8 Slot BRIC Solid State 96x8 1-Pole (3 sub-cards)
40-563A-121-96X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Solid State Multiplexer Module, Dual 3-Channel, 30 A, Hardware Interlock
40-667C-011-HI
-
The 40-667C-011-HI is a dual 3-channel 30A MUX with hardware interlock and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
Single 24-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-101
-
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI 8 Slot BRIC Solid State 128x8 1-Pole (4 sub-cards)
40-563A-121-128X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
IGBT Drive
-
IGBT gate drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode, signal processing circuit and power output transistor on the output side in a single chip. This coupler is designed specifically to provide high common mode transient immunity (CMR) and a high output current, and has an active miller clamp and high switching speed, making it ideal for driving IGBTs and MOS FETs.
-
Product
2x8 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9165A
-
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
PXI Solid State Multiplexer Module, Dual 3-Channel, 30 A
40-667C-011
-
The 40-667C-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 4 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-021-64X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Drive Tester
Disk Manufacturing Module
-
SCSI Toolbox LLC is proud to announce the Disk Manufacturing Module, joining a decade of real-world drive testing experience with input from hundreds of customers to bring the best new testing tool to the disk manufacturing and integration marketplace.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A, Hardware Interlock
40-667C-012-HI
-
The 40-667C-012-HI is a single 6-channel 30A MUX with hardware interlock and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
Solid State Relays
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Solid State Relays including Through-Hole and SMD, High Capacity and Phototriac Coupler Solid State Relays. Triac output components for AC load applications. Advantages include long operational life, high frequency switching, no contact arcs, high contact reliability, and noiseless operation.
