Compensators
-
Product
Potentiostat/Galvinostat
EZstat Pro
-
The EZstat Pro potentiostat/galvanostat uses a versatile menu-driven waveform generator (periodic or aperiodic) with preset battery cycling, Tafel plots, and cyclic voltammetry procedures.Users can program sequences of steps blending current and potential control with a resolution of 8 uS/point. EZstat Pro can perform electrochemical impedance spectroscopy (EIS) and uses active IR compensation. The instrument can interface with the EZpump peristaltic pump for flow batteries and fuel cells.
-
Product
Conductivity Meters
-
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
Resistivity Monitor / Controllers
750 Series II Resistivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Resistivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
High performance multisensor
Werth StentCheck®
-
High performance multisensor CMM with Integrated Werth Zoom® optic with magnification 0.7x – 6.8xRotary/Tilt Axis with high speed air bearing rotary axisRotary OnTheFly for fast measurementsContour image processing for fully automatic measurements of complex geometrical elements with sub-micron repeatabilityIntegrated goniometer (tilting axis) allows for the measurement of non-cylindrical geometriesUnique lighting design optimized for measurement of stentsTemperature compensation included
-
Product
4 Inputs Satellite Multi-Switch
HJMS-4400A (Cascadable)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*4 satellite IF inputs. *Built-in amplification circuit to compensate cable loss. *13/18V.22KHz switching. *Suitable for residential multiple LNBs reception. *Use receiver power as power supply. *Sheet Metal Housing.
-
Product
VIS/NIR Sensor
AF26
-
The AF26 is a high precision dual channel color sensor for inline operation; the secondary wavelength is designed to compensate the desired light absorbance measurement from any undesired light scattering influence, such as suspended solids, gas bubbles, immiscible fluids or window fouling. The AF26 sensor’s output can be correlated to almost any color scale including APHA and Hazen.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP023-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
CAT-5 Video Receivers
-
Analog Devices high speed, differential CAT-5 video receivers and equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths. Our video receivers provide excellent common-mode rejection that enables the use of low cost, unshielded twisted pair cables in noisy environments.
-
Product
TMD37003 cRGB Color and Proximity Sensor
SEN-36004
-
Fully integrated carrier board designed to get the most out of the TMD37003 cRGB (color with IR compensation) and Proximity Sensor from AMS. This means that the board includes a 1.8V-5V input range LDO and high-speed signal voltage translation on all IO pins. In addition, we've added a high output white LED that is tuned to the light temperature range of the TMD37003 IC. This makes sensing color of close-proximity objects possible, such as in robotic color sorting operations. As on many of our boards, we've included 4-40 sized mounting holes to make installation easy. The IC functions are interfaced via a 0.1" header, which includes power (Vdd and GND), I2C interface (again, fully translated) and a 3.3V input to power the proximity (IR) LED. The on-board LED is turned on with a logic 'HIGH' applied to the LED pin and is powered with Vdd.
-
Product
Time Domain Replication (Road Load Simulation)
-
The powerful graphical editor makes it easy to review and compile your field sample data for use in the test lab. The point editor, filters, velocity and displacement compensation ensure the test feasibility is evaluated at an early stage. The continuous closed-loop controller then replicates the test files with very high levels of precision. The control algorithms use a continuous coherence averaging technique to ensure a stable proactive control loop that will not only provide accurate replication but will also respond to changes in test item dynamics.
-
Product
Standard Airspeeds
-
These airspeed indicators have unrestrained movements.These instruments are actuated by ram air and ambient atmospheric pressure obtained from the aircraft pitot and static pressure systems. A moveable pointer and a fixed dial indicate airspeed with the zero index at the 12 o??lock position. Temperature compensation is internal and there is no external zero adjustment. Pointer damping is internally adjustable.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS800
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations.
-
Product
DC-to-250MHz, X1/x10 Probe Kit (HP-3250i), Isolated BNC
PRB-HP-3250i
-
Oscilloscope Probe 1:1-1:10 - HP-3250i250 MHz bandwidth, rated 600 V.The Oscilloscope Probe 1:1-1:10 - HP-3250i is a 1:1-1:10 selectable passive high impedance oscilloscope probe with 250 MHz bandwidth (1:10) designed and calibrated for use on oscilloscopes having an input impedance of 1 MOhm shunted by 20 pF. However, it may be compensated for use with an oscilloscope having an input capacitance of 10 to 30 pF.
-
Product
6GHz RF Signal Generator
TGR6000
-
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
Product
Electronic Differential Pressure
Density Measurement
-
An innovative software and hardware concept makes it possible to combine any two pressure transmitters of the VEGABAR 80 series into an electronic differential pressure system to measure density. Electronic differential pressure measurement is used for measuring density change and/or for compensation when the level needs to be measured.
-
Product
Wet/Wet Differential Pressure Transmitter
647
-
Monitor differential pressure in air/liquid flow systems, HVAC automation, pneumatic systems and process control with the Series 647 Wet/Wet Differential Pressure Transmitter. Units are temperature compensated and provide a 4 to 20 mA output signal which can be interfaced with chart recorders, data loggers and computerized monitoring and control systems.
-
Product
Bluetooth® Enabled PH And Temperature Pen
UltrapenX2™ PTBT2
-
*Accuracy of ± 0.01 pH*1, 2 and 3 Point Calibration*Automatic Temperature Compensation*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Live or Hold Mode – User Selectable*Proprietary Sensor Design*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated Electronics*Powered by One N Type battery (Included)*Waterproof
-
Product
AMR Linear Sensors
-
MultiDimension Technology Co.,Ltd.
AMR linear sensor utilizes two push-pull Wheatstone bridges each composed of four highly sensitive AMR sensor elements. These Wheatstone bridges effectively compensate the sensor’s temperature drift to achieve outstanding temperature stability with minimal noise.
-
Product
VECTOR-GUN HANDHELD DIRECTION FINDING ANTENNA SYSTEM
HFDF
-
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
Product
Dispersion Compensating Fiber
-
Dispersion compensating fiber from M2 Optics is used for correcting dispersion effects created over distances within G.652 single mode optical fibers. Offered in a 19" chassis for rack or benchtop use, these high quality testing platforms are easy to work with and provide consistent, repeatable results.
-
Product
Length Network Cable Tester
SC-8108
-
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
Product
JTAG USB Controller
NetUSB-1149.1/E
-
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
Mechanical Test Head Housing
-
a result of more than 10 years' experienceavailable with integrated manipulatorfully integrated docking and board lockingtest housing mechanics design as per customer specificationssuitable for individual and high-volume productionstandard and customized dimensionsno limitation in size and electrical power capacitiesquick and easy locking and unlocking process for board changelarge application space load boardoptional number of channel boards as per customer specificationsfamily/DUT board connection achieved by high-end double-ended spring probes - 50 Ohmhigh-end cooling fansfacilitated adaptation with all available manipulator solutionsdocking design in compliance with customer internal docking standards/dimensionsdocking force as per customer specificationscenter of gravity fully compensated
-
Product
Fixed Batteries (Constant Function)
-
Lifasa - International Capacitors, SA
Fixed compensation equipment has different variants depending on the type of enclosure / support and the configuration of the equipment (type of capacitor).
-
Product
Microohmmeter
MMR-6500
-
The MMR-6500 digital meter is designed for measuring low resistances with a stabilised current of up to 100 A. The use of test clamps enables the safe measurement of breakers (high-, medium- and lowvoltage), isolators and other components earthed on both sides. The MMR-6500 series meters are equipped with a unique module in their class that measures inductive components which have a current of up to 10 A, enabling the winding resistance of motors, transformers and other inductive components to be measured. Another useful function is the temperature measurement and the automatic compensation of results with relation to the measured temperature or temperature set by the user. The system is completed with a recorder function. Special measuring algorithms and additional functions allow an appropriate measuring method to be chosen depending on the measured component and measurement conditions, thus, widening the application areas of the meter. The state-of-the-art user interface, various communication interfaces, wireless communication and communication with the computer, printer, 2D code reader are integrals features which enable full, comfortable and intuitive management of not only measurements and their results but also ID data of measured components.
-
Product
pHTestr® 50 Waterproof Pocket pH Tester,
-
The Oakton pHTestr 50 has a replaceable double junction sensor for longer life, an expanded number of applications, and easy maintenance. Double-junction electrode sensor handles wastewater and solutions containing sulfides, heavy metals, and TRIS. Electrode sensor offers a clog-resistant Kynar® junction and a recessed, glass pH bulb to protect against breakage. Valox sensor housing resists most chemicals. The keypad clicks to confirm operation, and allows access to a variety of functions. Calibrate up to three pH points with the auto-buffer recognition at both USA and NIST standard buffers. Additional features include an automatic temperature compensation (ATC), hold function, auto-off function, self-diagnostic error messages, and a three-segment battery-life indicator.
-
Product
÷10, 500 MHz, 10 MΩ, Passive Probe (Total of 1 Per Channel)
PP008-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Beer Refractometer
PA202X-799-803
-
Dual scale Digital Beer Refractometer for measuring Brix or Specific Gravity (D 60/60) of wort. These beer scales are temperature compensated specifically for wort.
-
Product
pH Tester
148
-
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
