-
Product
Electronic Air Throttle Tester
DTA-1
-
Throttle is usually associated with petrol engines. However, throttle valves are also found in modern diesel engines. They are used under different names, often general and not linking to intake system.
-
Product
ELM Electronic Load Module
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
Electronic Design
-
We design and build custom racks, special switching systems, RF systems and custom Digital/ Analog sub assemblies. The hardware can be packaged per your requirements, using industry standard modules, rack mounted instruments, or custom made packaging. Extensive LabVIEW, embedded and other programming languages development are available as part of our hardware control support.
-
-
Product
Beam Geometry & Alignment Testing
-
Perform quality control testing of your Digital Radiography (DR), Computed Radiography (CR) and Fluoroscopy X-ray systems with ease. Comply with local, state, federal, and governing bodies for digital and traditional analog radiographic imaging technologies.
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
Product
DC Electronic Load
EE30140A
-
The EE30140A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
Product
Electronic Load
-
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
Product
Electronic Calibration Module (ECal), DC-4 GHz, 2-Port
N7550A
-
The N7550A is part of Keysight’s family of value-line electronic calibration (ECal) modules that makes calibration of vector network analyzers fast, easy and accurate. Cut your calibration down to half the time it normally takes using a traditional mechanical cal kit. Simply connect it to your instrument and the firmware does the rest. For greater precision and higher accuracy measurements consider the N44xx and N469x family of ECal products.
-
Product
Electronic Warfare MMI and HMI Simulators
MS 1600
-
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
Product
Carbon Fibre Beam Gauge
-
Designed to measure both internal and external diameters and lengths, the high modulus carbon fibre beam is stiff, lightweight and has an extremely low co-efficient of thermal expansion (CTE). Suitable for measuring high accuracy diameters and lengths up to 4000mm+.
-
Product
Bending Beam Load Cell
EST-7
-
Technopark Automation & Control
The EST-7 is a Bending Beam Load Cell suitable for use on lower capacity weigh hoppers, filling machines, packaging machines and conveyor belt scales. This load cell is available in capacities from 10 kg to 200 kg.
-
Product
Simulation Tools for Analog and Power Electronics
SIMetrix/SIMPLIS
-
Fast and accurate simulator for switching power circuits, fully utilising the SIMetrix development environment.
-
Product
10Ch Electronic Potentiometer 8 Bit
YAV90084
-
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
Analog Control Cable for Electronic Loads
EE105T-xx
-
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Product
Basic Electronics Trainer
-
Basic Electronics Trainer System to understand Characteristics of Variuos Type of Electronic Components.Functional block diagrams are provided on-board for Teaching/Training. These Trainer provides with various Test Points to Measure the Parameters on Multimeter.
-
Product
150 Watt Electronic Load Module
N3302A
Load Module
The Keysight N3302A is a 150 W (0-30A, 0-60V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3302A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3302A can also digitize waveforms.
-
Product
Electron Multiplication (EM) Standard Image Sensors
-
EM (Electron Multiplication) is a technology that uses on-chip gain in the charge domain to effectively eliminate read noise from an image sensor. This enables advanced ultra-low light applications that require extreme sensitivity at fast frame rates. Examples include life science applications such as single molecule detection, super resolution microscopy and spinning disk confocal microscopy along with physical science applications such as nanotechnology imaging, Bose Einstein condensates and soft X-ray spectroscopy, and astronomy applications such as adaptive optics and lucky imaging. The inclusion of an additional conventional output allows further flexibility for applications such as true 24 hour surveillance.
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
Custom Reed Relays from Pickering Electronics
Reed Relay
Pickering Electronics manufactures hundreds of model relays. Many of these custom reed relays are minor variations of a standard part, for example, a different test specification or pin configuration. Others are custom designed to meet our customer's particular requirements.
-
Product
Atomic Resolution Analytical Electron Microscope
NeoARM JEM-ARM200F
-
"NEOARM" comes with JEOL’s unique cold field emission gun (Cold-FEG) and a new Cs corrector (ASCOR) that compensates for higher order aberrations. The combination of a Cold-FEG and ASCOR enables atomic-resolution imaging at not only 200 kV accelerating voltage, but also a low voltage of 30 kV."NEOARM" is also equipped with an automated aberration correction system that incorporates JEOL’s new aberration correction algorithm for automatic fast and precise aberration correction. This system enables higher-throughput atomic-resolution imaging even at low accelerating voltages. Furthermore, a new STEM detector that provides enhanced contrast of light elements is incorporated as a standard unit.
-
Product
Beam Panoramic Power Supply Battery Crawler 40 to 160 kV
CP160CR
-
Designed to fit into 6” pipelines and higher, the CP160CR constant potential X-Ray generator for crawlers is – in its category – the most powerful panoramic X-Ray tube head in the world for crawlers. The generator is making the cutting edge constant potential technology of the CPSERIES even more compact into a 9.9 kg – 120 mm diameter X-Ray tube head. The crawler unit is capable of penetrating up to 28 mm of steel in 10 minutes, which corresponds to just a 25 second exposure time for 6” standard pipeline welds.
-
Product
Electronic Kits & Modules
-
This kit contains everything you need to build, the microcontroller will be programmed with the latest firmware before shipping.
-
Product
Electronic Flow Meters
5050
-
Parker Conflow’s Code 5050 is an electronic flowmeter that has a user-friendly display and is used for measuring and outputting flow rate, pressure and temperature
-
Product
Multi-channel DC Electronic Load
IT8700 Series
-
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
Product
Economical Single Point Bending Beam Load Cells
ESP SERIES
-
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
Product
Electronic Crockmeter
TF411
-
TESTEX Testing Equipment Systems Ltd.
Crockmeter, to determine the colour fastness of textiles to dry or wet rubbing. Electronic Crockmeter complies with ISO 105×12/D02, AATCC 8/165, BS 1006-D02, etc. Crockmeter is useful in crockmeter test and Crockmeter price is competitive.
-
Product
Power Electronics Test Solutions
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
