Current Clamps
measure AC or AC-DC amperage without contacting conductors.
-
product
AC Current Sensor
RCTi and RCTi 3ph
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
product
3KVA Leakage Current Tester
2675C3
Shenzhen Chuangxin Instruments Co., Ltd.
3KVA Leakage Current Tester
-
product
Leakage Current Alarm Signaler
MPU-1
MPU-1 is dedicated to control (measure) leakage current in AC, low and medium voltage power networks. It is designed to make measurements, which results define network's safety condition for leakage current. The device enables to set limit for maximum safe value of flowing leakage current and for values above this limit visual and sound alarm is activated.
-
product
Calibrator, Calibrated w/Data, Current, 185 mm, 78 mm, 38 mm
72-6694 CAL D
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
product
High Current Discharge Testing System
DTV
Cold Crank Testing to industry standards: IEC, SAE, BCIDischarge capacity performance testing to thousands of amperes
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
AC Current Probe 20 mV/A, 300A, 9.2 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable
T3RC0300-UM
AC Current Probe 20 mV/A, 300A, 9.2 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
43-752A-902
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
100A, 2 MHz, DC/AC Current Probe, BNC, 100A Peak, 70A rms, 1 meter cable
T3CP100-2
100A, 2 MHz, DC/AC Current Probe, BNC, 100A Peak, 70A rms, 1 meter cable.
-
product
Universal Clamp Tester
M-310
MULTI MEASURING INSTRUMENTS Co., Ltd.
The unique U type CT enabled to measure the load current of single or three phase cable without separating the cable to the wires. Leakage current measurements with least affection from the external magnetic field. Wide current measurements.(AC0.01mA-300A)
-
product
400A Dual Display Clamp Meter w/ Test Lead Storage
DL569
UEi Test & Measurement Instruments
Dual Display 400A Clamp Meter w/ Test Lead Storage
-
product
Clamp Meter, Auto, Average, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-9480
Tenma 72-9480 Digital Clamp Multimeter
-
product
Micsig AC & DC Current Probes
CP2100
Shenzhen Micsig Instruments Co., Ltd.
*Split design, small and exquisite appearance, easy to test *Compatible with all BNC-connected oscilloscopes, adapters can also work with multimeters.
-
product
AC/DC Digital Clamp Meter
Up to 400A AC/DC.Conductor dia. : Φ19mm max.True RMS.Peak Hold.Simple switch operation for easy of use.
-
product
Fully Automatic Eddy Current Crack Test System
ROTO-PUSH
Foerster Instruments, Incorporated
The ROTO-PUSH test station, which is integrated in production lines, serves to test cylindrical components for cracks in the liner surface. The testing configuration has to be rotated for automatic crack testing. After the test, the test pieces are sorted and separated. The continuous test run ensures a high testing rate, which increases profitability.
-
product
Current Sensing Resistors: ACQ-200
TCS
These components are four-terminal. bus-bar, metal strip current shunts. Assembled using electron beam welding. These units can handle 15W of continuous power and a maximum current of 350A 90.1mohm). Also they can absorb a high pulse power rating and have very low inductance. They also feature excellent long term stability, less than 100ppm/C TCR, and have excellent frequency characteristics.
-
product
C/I Clamp Meters
*AC current measuring capability up to 400 amps*Compact size, fits easily into tool pouch*Data hold and Max hold to capture important readings*Lifetime Limited Warranty
-
product
Clamp Meter 3999 Counts DC/AC
VA311
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Clamp meter DC/AC VA311 Autorange economic DC and AC clampmeter up to 1000A with temperature and capacity function.
-
product
DC Coupled Current Probe
34134A
Measure a wide range of applications with this battery-powered, clamp-on probe; use with DMMs or voltmeters
-
product
Current Probe
PA-699
*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability
-
product
Eddy Current Dynamometer
EC Series
Specifically designed for small displacement diesel engines, the Eddy Current (EC-Series) engine dynamometer features in-line eddy current absorption units in a robust, compact frame. The air-cooled eddy current absorbers eliminate the need for an expensive water recirculation system and most engines being tested can be cooled with a standard closed-circuit radiator system. This compact air-cooled design results in a minimal environmental impact and the ability to be easily relocated with no need for a permanent installation. When combined with PowerNet LT, our fully automated dynamometer control system, all of your testing needs can be performed at the touch of a button.
-
product
Current Measurements of PWM or Inverter, AC/DC 10～200A, φ24mm
CTF-200DC
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
-
product
Capacitor Leakage Current Meter
DU2316/2317
Delta United Instrument Co., Ltd.
Leackage Current range display: 0.0001uA ~ 20.00mAAutomatic or Manual trigger with CHARGE/TEST/DISCHARGE100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceHi / Lo current limit setting & PASS/FAIL judgment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Digital Current Integrator
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-80
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of main cable*BIG CT WINDOW*AC 1mA～500A
-
product
High Current SMU Family 2000 A
AXC76xx
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
product
Split type Pulse Current Sensor
CTF-05K
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Clamp type CT.*Open collector output.
-
product
Current To Pressure Measurement Trainer
Unitech Scales And Measurements Pvt. Ltd
Current to Pressure Trainer. This setup comprises of a I to P converter fitted on a base. Two pressure gauges are fitted one at the input side and the other at the output of the I to P converter. A current source with digital display is provided to excite the I to P converter. A constant air supply should be provided to the system at 20 PsI Pressure from a standard compressor.
-
product
AC/DC Clamp Meter
ST-3602
Standard Electric Works Co., Ltd
● 3½ digit LCD with maximum reading of 1999.● Over range indication : "1" is displayed on highest digit.● Low battery indication: "B" sign appears on the display.● Response time: approx. 1 second.● Data hold: for all ranges
-
product
Software for Current & Water Quality Monitoring Data Analysis
DataStudio 3D
Aanderaa, a Xylem brand, is a technology provider of oceanographic sensors, instruments and systems which are able to measure environmental parameters such as wave, current andwater quality (Dissolved Oxygen, Salinity, Temperature, Depth and Turbidity) over long deployments, several years.Data analysis is an important stage in all environmental monitoring campaigns. In many situations, users have to download and filter through large data quantities for analyses. DataStudio3D is a free data analysis software available to Aanderaa SeaGuard and SmartGuard users.To aid in data analysis, Aanderaa has developed their own propriety software, DataStudio3D which allows users to download field data and plot them on different graphical plots. This mode of data analysis can be carried out within minutes to help user to compare parameters, view trends, anomalies, and to control the data quality.
