Filter Results By:
Products
Applications
Manufacturers
-
product
USB Power Delivery Test Equipment
The Packet-Master USB-PDA is a USB PD Analyser, for FSK and Baseband variants of Power Delivery.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-03
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
PCIe Direct Digital Synthesizer
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.
-
product
PXIe-5672, 2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator
779900-01
2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator —The PXIe‑5672 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5672 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee.
-
product
DDS Function Generator, Digital Control 10MHz Or 20MHz, With/without USB/RS232 Interfaces
TG2000 Series
0.001Hz to 10MHz/20MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logAM, FSK, gated and tone switching modes5mV to 20V pk-pk from 50 or 600 OhmsStorage for multiple instrument set-upsUSB and RS232 Interfaces (TG2000 only)
-
product
Central Office Line Simulator
AI-7280
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
product
Production Caller ID Signal Simulator
AI-80
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
product
3MHz Multi-Waveform Signal Generator with Modulation
Model MSGM3M
- 0.3Hz to 3MHz Frequency Output in 8 Ranges- Versatile Waveforms: Sine, Square, Triangle, Ramp, Pulse and DC outputs- Standard AM, Balance AM, FM, ASK, FSK, PWM Modulation and Sweep Mode- Internal / External Modulation
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781262-02
6.6 GHz PXI Vector Signal Generator - The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXI-5670, 2.7 GHz PXI Vector Signal Generator
778768-02
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
product
Signal Generator
AG4151
Advanced DDS technology,Max 150MHz frequency outputUp to 400Msa/S sample rate and 32bits Frequency resolutionVertical Resolution : 14bits,up to 1M wavelengthComprehensive waveform outputs:sine,square,ramp,pulse, noie,sinc,exponential rise and decay,32 channels digital waveform ,DC and user defined arbirary waveformComprehensive modulation functions:AM,FM,PM,FSK,PWM modulations3.9 inch high resolution (480x320 pixels)TFT LCD display
-
product
PXI-5670, 2.7 GHz RF Vector Signal Generators
PXI-5670 / 778768-03
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
product
100MHz Signal Generator
DDS8m
The DDS8m generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The DDS8m is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. SOF8 windows software is available as an extra cost accessory.
-
product
PXIe-5672, 2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator
779900-03
2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator —The PXIe‑5672 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5672 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee.
-
product
100MHz DDS Signal Generator
408A
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
product
Basic Basic Butt Set For Phone Line Testing
BSX200
Triplett Test Equipment & Tools
BSX200 Basic Butt Set is designed for people who occasionally need to deal with dial tone but don't require all of the features of an expensive model. The BSX200 provides user with dial tone, dial out, Caller ID, last number redial, on/off hangup button, flash button, DTM and FSK support, and three ways to connect to the line: an RJ11 connector, high quality alligator clips, and a type 66 adapter.
-
product
PCI Synthesizer
SYNTH300 Series
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
-
product
Pulse Function Arbitrary Noise Generator
81150A
1 - 120 MHz pulse generation with variable rise/fall time1 - 240 MHz sine waveform output14-bit, 2 GSa/s arbitrary waveforms512k samples deep arbitrary waveform memory per channel Noise with a selectable crest factor and signal repetition time of 26 days FM, AM, PW, PWM, FSK modulation capabilities up to 10 MHz1 or 2 channel, coupled and uncoupled Differential outputs
-
product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
High Performance Function/Arbitrary/Pulse Generator 25MHz Or 50MHz, 1 Or 2 Channels
TG251xA/501xA Series
One or two channels0.001mHz to 50MHz/25MHz range; 14 digits or 1uHz resolution.Standard waveforms include sine, square, ramp, pulse, sin(x)/x, noise, exponential, logarithmic and PRBS.True pulse generator with variable delay and variable rise/fall.Arbitrary waveforms of up to 128K points at up to 125MS/s.Waveform storage using USB flash drives.Large graphic LCD with simultaneous text and waveform display.Comprehensive internal and external digital modulations including AM, FM, PM, PWM, FSK, BSPK, Sum and PRBS.20mV to 20V pk-pk output from 50Ohms ; plus multi function aux. out.Storage for multiple instrument set-ups in non-volatile memory.Waveform Manager Plus for Windows software included.Programmable via USB and LAN (LXI) interfaces; GPIB optional
-
product
5 / 10 / 20 MHz Multiwaveform Arbitrary Signal Generator
MASG Series
- Economic and Light Weight- Dual Output with Same Characteristic- 1µHz Frequency Resolution- 11 Built-in Waveforms and 5 User defined Arbitrary Waveforms- AM, FM, PM, PWM, FSK Modulation, Frequency Sweep and Burst Function- Built-in 100MHz Frequency Counter- Arbitrary Waveform Editing PC Software- USB Host, USB Device
-
product
Digital and Analog Communications
1. Design and implementation of RF oscillators and filters. 2. Design and implementation of analog AM and FM modulation and demodulation. 3. Design and implementation of digital and analog converter. 4. Design and implementation of ASK and FSK modulation and demodulation. 5. Design and implementation of PSK and QPSK modulation and demodulation.
-
product
Universal Power Line Carrier
UPLC-ll
As with our previous UPLC power-line carrier design, UPLC-II requires no hardware modifications for most required configurations. UPLC-II is frequency programmable across the entire power-line carrier spectrum (30 to 500 kHz) without changing any hardware components. UPLC-II can be software configured either as an ON/OFF or frequency-shift keyed (FSK) power-line carrier unit without changing any hardware components. This flexibility makes each UPLC-II universally suited for any directional comparison blocking, permissive, phase comparison or transfer trip protective relay application.
-
product
Quadrature Signal Generator
TE5100-PCI
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
DDLS 200 with 2 Mbit/s Transmission Rate
Leuze electronic GmbH + Co. KG
Optical data transmission for RS interfaces and fieldbuses up to 300 m and up to 2 Mbit/s. Infrared data transmission protects the DDLS 200 from interference. Systems are available for all common industrial fieldbus interfaces. The ranges are stepped and reach a maximum transmission distance of 300 m. Low ambient light sensitivity through special FSK method. Available interfaces: PROFIBUS, Interbus and CAN/DeviceNet, as well as RS422 and RS 485.
