Insertion Loss & Return Loss
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
PXI Differential Fault Insertion Switch Modules
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
product
VTAC, Insert Bundle, Receiver/ITA, SIM, Vertical Header and Pass-Thru
610151108
Each kit contains (1) VTAC vertical header insert and (1) VTAC pass-thru insert. VTAC vertical header inserts get press fit into a PCB and by extension of the VTAC pass-thru insert, a VPC receiver connector can be mounted to the PCB. This is especially useful when mounting an i2 MX receiver or 90 Series SIM module to a PCB.
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle Insert, 36", Single Ended
7-151924000-036
Signal, Patchcord, ITA, 36", QuadraPaddle Insert, 36", Single Ended
-
product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
CATV Return Band Two Carrier Generator
PC-2
The PC-2 is a compact, temperature-stable two RF-carrier source. It is designed to be used for activating and testing the return-band. When used with a signal level meter, the PC-2 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.
-
product
Channel Insertion & Encoding
ATX’s encoder products provide a cost-effective and space-efficient solution for digital transmission and/or insertion applications. ATX’s fully integrated wall or rack mount “single unit” line of products are ideal for inserting security camera video into MDUs, inserting barker or information channels into hotels and other commercial properties, for digital simulcast applications, and for digital delivery of PEG or hub site specific programming.
-
product
ITA, i2 MX, EMI, w/ 2 Hybrid Module Inserts, XL Backshell (XL Bend Radius and Cable Exit)
410130132
This model i2 MX includes 2 Hybrid Module inserts. Each module insert includes 8 Mini Power/Coax and 8 TriPaddle positions. The XL-sized backshell allows for a greater cable bend radius and large cable exit which accommodates larger, high speed cables or a high volume of twisted pair combinations. The max cable bundle eff diameter= 1.67".
-
product
VTAC Right Angle Insert
Modular and compact, VTAC right angle inserts are used to provide a high speed data connection to a PCB.
-
product
Two-Way Optical Loss Tester
KI23403OLV-INGAAS-APC-50U
A Two-Way Optical Loss Tester (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on multimode fiber at 850 / 1330nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. A multimode APC connector on this model is required for reliable ORL test performance.
-
product
Loss Measuring System for Transformers
LiMOS
HIGHVOLT Prüftechnik Dresden GmbH
The transformer loss measuring system LiMOS is designed for highly accurate measurement of losses and other parameters required in the framework of routine and type testing of power transformers. The combined voltage/current sensors and the digital signal processing enable a very compact design with only one HV device per phase with smallest volume and footprint. The digitized and preprocessed signals are transmitted via fiber optic cable to the receiver unit (LiMO-MCSU).
-
product
Signal/Mini Power/ Mini Coax, Module Insert, ITA, i2 MX, TriPaddle, 8/8 Position
510144005
Signal/Mini Power/ Mini Coax, Module Insert, ITA, i2 MX, TriPaddle, 8/8 Position
