Reflection
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
cPCI 3U RD
-
Hartmann Electronic’s board design is based on the HIGH-SPEED DESIGN concept. Low reflection is achieved by means of uniform signal surge impedance. The backplane design features an energy buffering feature which works across the entire frequency range.
-
Product
3D Laser Imager
Vector-DD
-
The Vector 3D laser imager offers multi wavelength, full waveform data capture, coupled with the flexibility of an all-sky scanner. The Vector-DD is a direct detection (DD) 3D (range, angle, angle) active imager with an all-sky full hemisphere scanner. It employs a nodal point design so that all the lines-of-sight converge to a single point at the instrument*. In addition, two wavelengths can be transmitted so that differential reflectivity information can be derived. The unit is compact and portable and operates from 24V DC.
-
Product
Integrating Spheres - Luminous Flux Measurement For LEDs And Lamps
-
Konica Minolta Sensing Americas, Inc
One of the most important tests in light measurement is the assessment of the total radiant power or luminous flux of light sources using integrating spheres. An integrating sphere’s inside surface is coated with a diffusely reflecting material which guarantees complete integration and homogenization of the emitted radiation. The integrated light is then measured at the detector port.
-
Product
Self-contained Photoelectric Sensors
PZ-V/M Series
-
Automatic Calibration Photoelectric Sensors. Detections are unaffected by variations in target color or angle. Excellent resistance to dust and dirt. One touch, fully automatic calibration. Unaffected by highly reflective target backgrounds. 40 model variations available including quick disconnect types. High-power red LED(Except for PZ-M71/V71)
-
Product
FTTH Optical Node
SR201W
-
Hangzhou Softel Optic Co., Ltd.
SR201W is a mini in-door optical receiver with WDM that especially design for FTTP/FTTH application. High performance, low receiver optical power and lower cost is FTTH solution best selection for MSO. WDM integrated for 1550nm video signal and 1490nm /1310nm data signal in one fiber. Reflection 1490nm/1310nm for connecting ONT device. They are very suitable for PON and TV system
-
Product
Logic Analyzers
-
Verification and debug of today's high speed, low voltage digital signals requires probing solutions that can accurately acquire from a wide variety of electronic designs and protect signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions.
-
Product
Sparse Nodal Solution
MicrOBS
-
MicrOBSNT is an ocean bottom node solution for seismic refraction and reflection surveys.
-
Product
Calibrated Diffuse Reflectance Standards
-
Diffuse reflection calibration standards in synthetic ODM and ODMP material
-
Product
2x2 Interferometric Couplers
-
Feasa manufactures a series of couplers, which are optimised for use in fiber interferometers. The couplers have a highly reflective end on one or more output ports and can be configures as 1x2 or 2x2.
-
Product
Non-Contact Type Handheld Digital Tachometer
HT-4200
-
The HT-4200 is a compact, non-contact type handheld digital tachometer. Affix one of the reflective marks to the rotating surface of the target measurement object, and then aim the red visible ray at the mark. If multiple marks are affixed to the target of measurement object, measurement can be performed at a lower speed.
-
Product
IR/Visible Target Projectors
-
Santa Barbara Infrared’s reflective infrared and visible target projectors are turnkey test systems for electro-optical (E-O) testing of FLIRs and other infrared (IR) and visible imaging systems. The standard target projectors are assembled from SBIR’s STC Series Collimators, Infinity Blackbodies, Infinity VSX Integrating Spheres and 300 Series Target Wheels.
-
Product
Sensors
-
A speed and angle sensor using a black/white tape which is glued on a rotating part. The reflection is converted into a TTL signal, bandwidth 100 kHz. The sensor consists of a tiny electronics part and a 5 m fiber optic cable terminated with a M6 screw. Thus areas where space is very limited still can be reached conveniently.
-
Product
Power Supplies
CUL-550B
-
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
Glass Thickness Meters
-
Shenzhen Linshang Technology Co., Ltd.
As a supplier of laser glass thickness gauge and glass thickness measuring tool, Linshang provides two models of glass thickness gauge that can be used to measure the thickness of various glasses, i.e: single-layer glass, double glazing, triple glazing, multilayer glass, LOW-E glass, and insulating glass, especially suitable for installed glass, such as doors and windows, curtain wall glass, etc.. It can measure the glass thickness as well as the thickness of air space (between the glass). The glass check works on the basis of reflection in the glass.
-
Product
kSA Emissometer
-
The kSA Emissometer is designed to quickly and easily generate high-resolution diffuse and specular reflectance and total emissivity maps of MOCVD carriers. Carrier emissivity variation means temperature non-uniformity, which can lead to reduced device yield and possibly complete growth run failure. With the kSA Emissometer, emissivity changes can be tracked to determine carrier end-of-life, without wasting growth runs. The kSA Emissometer also detects unwanted residual deposits after baking, and easily identifies carrier surface defects, scratches, microcracks and pits that are not visible to the eye.
-
Product
6x (1 to 4) 50 Ohm 2.5 GHz MCX Multiplexer
YAVAL034
-
6x (1 to 4) MMCX connectors CAN Control (or Ethernet with Ethernet to CAN Gateway) Reflective
-
Product
Display Measurement Systems
DTS Series
-
Instrument Systems Optische Messtechnik GmbH
Characterization of emissive, transmissive, reflective, and transflective displaysViewing-angle-dependent analysis of illuminance, contrast, color, and derived parametersDetermination of the electro-optical transfer function: analysis of luminance, contrast, and color depending on electrical driving conditionsMeasurement of transient properties, such as switching times, flicker, and modulation
-
Product
Capsule Hydrophones
HGL-series
-
The HGL hydrophone has been established as a workhorse for diagnostic level measurements, providing the best mix of frequency response, reflection profile, and aperture size.
-
Product
Reflection Meter
RC-088
-
This instrument is a special equipment for measuring the reflectivity of rearview mirror (or similar product) of motor vehicle. The product composes intelligent measuring instruments, optical integrating sphere, parallel lamp, standard light source, constant current source etc. It is easy to operate，it can measure the reflectivity quickly and accurately. On instrument structure, it adopts standardized modulation design. It takes latest single chip as its digital central processing element. After the measuring signal is converted by modulus, CPU will do some computation and compensation. The instrument can display the reflectivity of device which is measured in rear time. It operates simply and quickly, the indication is direct and accurate. It’s good for quality examination &control in the production scene as well as laboratories. This product has the convenience &quick demarcation way, can meet requirement of different occasion. It is applicable for measuring light reflection on mirror and not mirror parts.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
Convergent Reflective Micro Photoelectric Sensor
PM2
-
Panasonic Industrial Devices Sales Company of America
The fixed beam of focused light from the Convergent Reflective Type Micro Photoelectric PM2 Sensor enables it to precisely detect an object within a defined sensing range. With the ability to measure independently of the background, the PM2 Sensors are also able to detect dark or slightly reflective objects as well as extremely thin objects (> 0.05mm). These features, combined with its compact and robust design, make the PM2 Sensor suitable for a large number of applications.
-
Product
Active Peak Reading Wattmeter
HF/6
-
Active peak reading wattmeter with simultaneously variable hold time on both the forward and reflected meter movements. This variable delay can be adjusted for quick action for high speed CW, or for longer periods more appropriate for the display of SSB and AM voice peaks. The peak detectors sport a new fast attack design capable of capturing quick pulses such as a single dit. Beautiful industrial design with tri color meter scale and brilliant LED illumination make the DWM series wattmeter a beautiful addition to any station.
-
Product
Distance Sensors
-
SICK has a wide range of optic and ultrasonic solutions that measure from sub-microns to kilometers. They solve measuring, detecting and positioning applications using triangulation and time-of-flight modes. Sensors using triangulation are ideal for short-range, highly precise measurement. They can inspect miniature parts, thickness and shape, etc. Time-of-flight sensors work at longer distances, are not influenced by reflectivity or ambient light − perfect for positioning AS/RS, rail cars and gantry cranes.
-
Product
Pro Laser Tachometer
332
-
The #332 is the ideal tool for easy and accurate measurement of RPM in almost any environment. Simply aim the laser beam at a reflective mark placed on a rotating device, push the button and the RPM reading is immediately displayed. No contact with the shaft or wheel is necessary. The laser beam is not affected by shop light and can detect RPM from longer distances of up to 6 feet away. The #332 can measure up to 99,999 RPM in 1 RPM increments. It can be used to measure RPM on coil-on-plug and diesel engines, where conventional inductive tachometers can not be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included.
-
Product
Fully Reflective Solar Simulators
-
Sciencetech manufactures four high power versions of class AAA fully reflective solar simulators. Sciencetech''s proprietary fully reflective design uses metal coated mirrors and passes the whole spectrum, no compromise. This is a distinct advantage over refractive based systems that are limited by the properties of the transparent material used.
-
Product
Digital Tachometer
TAC-L
-
Model TAC-L Portable Digital Tachometer measures rotational speed either by contacting a rotatable head to the shaft of the object, or using photo sensor to detect the reflections from the laser. The laser target can record from a distance of up to 20 inches and gives a more accurate measurement than LED targeting. Model TAC-L includes a large LCD with a backlight for use in dark areas.
-
Product
Goniophotometer Test System For Led Lamp
LCG-1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
Digitize, Quantify, Collaborate With Your Unique Automated Petrographic Microscope
ZEISS Axioscan 7 for Geology
-
Digitize your thin sections with Axioscan 7 – the reliable, reproducible way to create high quality, digitized petrography data in transmitted and reflected light. Uniquely designed for petrographic analysis, the Axioscan 7 Geo combines unique motorized polarization acquisition modes with unprecedented speed and a rich software ecosystem for visualization, analysis, and collaboration.
