Drivers
translate general instructions into hardware specfic commands.
-
Product
PXI Simulation Modules For Sensor Simulation
-
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
Product
PXIe-SMN Interface Card
-
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
Product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785597-02
FlexRIO Signal Generator
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 4 Channels
M4I.6622-X8
Arbitrary Waveform Generator
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
Product
Diode Laser Driver
D200
-
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
Product
General Inclinometers
-
Columbia Research Laboratories
Columbia's SI-701 Series of Inclinometers are electronic tilt sensors based on Force Balance Accelerometer technology. They produce high level low impedance output proportional to the sine of the tilt angle. Model SI-701B is a low cost general purpose sensor that can be up-graded with the addition of the Columbia "HP" torquer system (SI-701BI) for greater accuracy and ruggedness. A bi-axial version of both units (SI-702B) is also available. The Model SI-701BI is designed with an output circuit made for 4-20mA data transmission systems for industrial applications. The model SI-701FND is a fluid dampened premium performance inclinometer designed to produce accurate tilt data in extreme shock and vibration environments. The latest addition in the line is Model SI-701WPBI, a waterproof (to 150 feet) inclinometer which operates from a +15 volt supply with 4-20mA output. A single power supply powers both the sensor and the 4-20mA line driver.
-
Product
- RS-232 High Speed Line Driver with LCD Display
Model 227
-
FEATURES: DataSpy Status Display; Full Duplex to 5 Miles; Async, DC to 115.2 KBPS; Powered by TD; RJ-11 and Screw Terminals for the Line Interface; Built-in Surge Protection; Fully Compatible with Model 201 up to 19.2 K. The Model 227 RS-232 High Speed Line Driver with LCD Display provides full-duplex transmission from DC to 115.2 KBPS over two twisted pairs.
-
Product
USB BUS Controller Board
MS 1711
-
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
C Series Counter Input Module
Input/Output Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
4 Channel 1.0 ~ 17.0 Gb/s Pulse Pattern Generator and Error Detector
CA9806
-
The UC INSTRUEMNTS CA9806 is a high performance, flexible four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (consult factory for higher or lower operation speeds). It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build‐in 8.5 ~ 15 Gb/s eye diagram testing function.
-
-
Product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T02
Temperature Sensor
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Isolated RS-485
-
Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications. The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus.
-
Product
USB-6001, 8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782604-01
Multifunction I/O
8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6001 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6001 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB-6001 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
- Optically Isolated Line Driver
Model 72A
-
FEATURES: DC TO 19.2 KBPS; Optically Isolated; TD & RD LED's; Loopback Switch; Built-In Surge Protection; Male or Female Connectors; Screw Terminals and RJ-11. The Model 72A Optically Isolated Line Driver links RS-232 based devices over extended distances. It provides optical isolation and has built-in verification of operation using a loopback switch.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785958-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Air-Cooled Universal Test Platform
Diamondx
-
Diamondx semiconductor test system extends Cohu’s low-cost, high-throughput production test solution platforms to high pin count, higher site count wireless, mobility, SOC, Flat Panel Display drivers, Power Management, and microcontrollers. Designed to meet the cost drivers IC companies face, Diamondx extends Cohu’s leadership in lowering the cost of operations.
-
Product
Syringe Pump
500xv
-
The 500xv is able to pump higher viscosity material by reducing the restriction within the pump, specially designed with 3/8” ports at a 45 degree angle. Ball valves are used for automating refill and continuous flow which clear easily.The 500xv syringe pump provides precise delivery of high viscosity material up to 204 mL/min. Pulse-less flow is delivered up to 5,000 psi (345 bar) for pumping thick materials. Viscosity can be reduced by heating the pump chamber. A Temperature Control Jacket can be used to raise the temperature above ambient up to 100 ◦C.The High Temperature package allows the ability to heat up to 200 ◦C.The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller.The 500xv pump module has a single-ratio drive train with auto-lubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure.
-
Product
PXI 64 Channel Relay Driver Module
40-411-001
Relay Driver
The 40-411 is the perfect solution for driving external relays from a PXI system or from Pickering Interfaces LXI modular chassis. Each module provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one side of the relay coil and the other side to the 40-411 output. Each output is capable of sinking up to 1 Amp of continuous current.
-
Product
PXIe-4303 , 24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module
783866-01
Analog Input Module
24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4303 is a filtered input module for voltage, thermocouple, and current measurements. The module offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
Microwave Switches
SMX-7XXX (Microwave)
Microwave Switch Module
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
Product
GPIB-RS232, Instrument Control Device - United States 120VAC
779732-01
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PXI Oscilloscope 2 Channel, 250Msa/s
PXI‑5114
Oscilloscope
The cost-optimized PXI‑5114 oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also offer a variety of trigger options, large onboard memory, and a device driver that includes streaming and analysis capabilities. The device is particularly suitable for applications with fast signals that require flexible measurement configurations and an analog bandwidth of up to 125 MHz. The PXI‑5114 also features PXI‑based synchronization and data streaming capabilities.
-
Product
PXI-2567 , 64-Channel PXI Relay Driver Module
778572-67
Relay Driver
64-Channel PXI Relay Driver Module—The PXI‑2567 is an external relay driver that works with internal or external power sources. The PXI‑2567 allows you to control relays when the current and voltage requirements for those relays exceed the capabilities found in existing relay modules or for relays embedded in a test system. The PXI‑2567 includes overcurrent, overvoltage, and flyback protection to ensure long-life operation. The PXI‑2567 can also drive small DC motors or other inductive relay coils.
-
Product
Overhead Board
OVH-380-2
-
Curtiss-Wright Defense Solutions
The OVH-380-2 is the enhanced overhead board for the AIM/ HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers, and terminates the IP stack for Ethernet support. It also receives and formats inbound (acquired) data.
-
Product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Korea 220VAC
781630-09
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
CNC Machine Network Solution
WebAccess/CNC
-
Webaccessoryess/CNC supports diverse SCADA drivers, CNC, I/O, PLC devices for efficient equipment data collection & networking app development.
-
Product
MIL-STD-1553 A / B Test And Simulation 3U PXI Module
PXI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*PXI trigger on 1553 bus events*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Combo Unit, 7.5 Digit Digital Multimeter (DMM) with 10-Bit 1GHz Digitizer in a Single VXI Slot
6084A
Digitizer
Increases test system performance and density with this combo unit, which packages a 7.5 digit Digital Multimeter (DMM) together with a 10-bit, 1 GHz Digitizer into a single VXI slot.Replaces the Wavetek 1362 DMM, Analogic DBS Series, and Agilent VXI DigitizersDigitizer with 4 Inputs, 10-bits, 1 GHz, up to 4 GS/s and Ranges up to 500V DMM with 7.5 Digits for DC Volts, Current and Ohms with AC Volts up to 1 MHzIVI-COM Drivers and Soft Front Panels ProvidedMore Dynamic Range (by 20 dB for DMM and 12 dB for Digitizer) for Better Legacy Range Mapping
