Motor Test
See Also: Motor
-
Product
Custom Motor Test Systems
-
Magtrol's Customized Motor Test Systems (CMTS) are PC-based, turnkey systems custom designed and built to meet your specific motor testing requirements. By integrating Magtrol's motor test equipment with power supplies, adaptable fixtures, custom tables/cabinets, printers, etc., Magtrol's engineering team can customize PC-based, turnkey systems and modular test benches for almost any motor test application.
-
Product
Traction and Induction Motor Test Systems
-
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
Product
Motorized Force & Torque Measurement Test Stands
-
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
Product
Motor Test for Stepping Motors
-
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
Product
Exacting Electric Motor Testing
-
The Taylor Dynamometer Electric Motor Test Stand is designed to provide maximum reliability, excellent durability and flawless performance. Using our extensive line of Water Brake engine dynamometers, Taylor Dynamometer has systems available for testing electric motors from 5 to 13,000 hp (3.7 to 9,694 kW). Include an instrumentation package to achieve your testing requirements. From simple speed, torque and power display systems with manual control to completely automated testing solutions, Taylor Dynamometer has a system to meet your testing requirements.
-
Product
Surge with 3 Phase Transfer Switch Consoles
TC Model
-
(Surge with 3 Phase Transfer Switch Consoles) Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TC" Model has the same characteristics as the "C" Model, but includes a Built-in 3 Phase Test Selector Switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Dynamic and Fatigue Testing Systems
-
Instron offers an extensive range of fully-integrated dynamic and fatigue testing systems from 1000 N up to 5000 kN. Incorporating servohydraulic, servo-electric and linear motor technologies, these test instruments cover a broad range of fatigue, dynamic, and static testing applications. These applications include high-cycle fatigue, low-cycle fatigue, thermo-mechanical fatigue, fracture mechanics, crack propagation and growth studies, fracture toughness, bi-axial, axial-torsional, multi-axial, high strain rate, quasi-static, creep, stress-relaxation, and other types of dynamic and static tests.
-
Product
Motorized Test Stands
-
Imada offers basic and advanced motorized test stands that are available in Standard, High, and Low speeds.Use ZTS or ZTA force gauges with MX, MX2 or EMX Series test stands to enable force control and non destructive testing.
-
Product
AC Flash Tester
THPG
-
Very Heavy Duty with high milliamp capacity for properly testing motors and windings.
-
Product
Adhesion and Peel Tester
-
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Product
Brushless/Servo/Stepper Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
Product
Motor Test Port
MTAP2
-
We know safety is number one priority in any motor reliability program that is why PdMA developed the MTAP2, our answer to safe electric motor testing. With the combination of MCEMAX® or EMAX, the MTAP2 makes testing easier, faster and above all safe!
-
Product
Motorized Test Stands
-
AMETEK Sensors, Test & Calibration
Our motorized test stands are optimized for production floor operation. They provide a constant test speed and require a force gauge to be integrated with the test stand.
-
Product
Linear AC Power Supply
-
Applicable places : equipment testing, compressor testing, monitor testing, motor equipment testing, air conditioning equipment testing, optimal power supply for R&D units, testing of various electrical products, 400Hz power supply for military equipment, special power supply for switching DC power supply testing, transformer /TRIAC / SCR...
-
Product
Dynamic Electric Motor Analyzers
-
Baker's dynamic motor test and monitoring instruments are built to conduct condition monitoring tests of motors and generators from a Motor Control Centre (MCC), or through a Baker EP1000 connection unit. The Baker EXP4000 dynamic motor analyser is a low-voltage, AC- and battery-operated instrument that test motors and generators while they are in operation. The EXP4000 provides health and performance data on the motor, the motor's load, and incoming power to assess motor performance and suitability in context of the entire machine system it supports.
-
Product
Motor Test for Electric Scooters
-
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
Product
Test Stands: Mechanical and Motorized
-
SHIMPO offers both motorized and mechnical test stands suitable for the most precise testing applications.
-
Product
Motorized Test Stands
-
The Chatillon motorized test stands are optimized for production floor operation.
-
Product
COF Testers
-
Coefficent of Friction Testers are composed of a motorized test stand, digital force gauge, COF sled and table and specialized software. COF testers measure the static and kinetic coefficients of friction of plastic film, sheeting and similar thin materials.
-
Product
Motor Test Bench For No Load Test
-
The testing equipment is extensively used in industries for testing of motors under no load conditions.
-
Product
Wireless TRMS Clamp Meter w/ 3-Phase & Imbalance Motor Tests
DL599
-
UEi Test & Measurement Instruments
TRMS Wireless Clamp Meter w/ 3-Phase & Unbalanced Load Tests
-
-
Product
Performance Dynamometer
-
The MD-250-HD was designed to be a performance dynamometer first, with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD can boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD with 900-hp worth of loading capacity for steady state testing.
-
Product
On-Line Electric Motor Analyzer
EMAX
-
We understand that shutting down electric motors for testing can be time consuming and costly. With the EMAX technology you can now test a motor while it is operating with no interruption to production. Within seconds the EMAX will provide a comprehensive detailed look at the Power Circuit, Power Quality, Stator, Rotor, and Air Gap.
-
Product
Circuit Tester
69105
-
Tests circuits rated from 80 to 600 volts AC/DC.High-visibility neon lamp indicator.High-impact, sealed 5-11/16'' (144 mm) probes on long 24'' (610 mm) leads for convenience in testing motors, fuses, relays, switches, etc.Resistor between each probe and lead.Reliable electronic components.
-
Product
Testing Aerospace Motors
-
Magtrol designed this Custom Motor Test System for the testing of various aerospace motors for both commercial and military applications.
-
Product
Pump Testing with NPSH Measurement
-
Test field for centrifugal and side channel pumpsfor split-case pumps or as a complete unit with customer engine.*Open tank system for recording QH characteristics*Vacuum-resistant container for NPSH measurements*Three flexible test cars with height-adjustable test motors: 5/30/90 kW
-
Product
Linear Vibration Motor Aging Unit
BK2019A
-
The BK2019A Linear Vibration Motor Aging Test System was designed to test your linear vibration motors for long term reliability. It can test 20 DUT’s at one time and you can stack them easily so you can test hundreds of DUT’s simultaneously in a small space. This is a great machine to ensure your product will do its job for it's expected life.
-
Product
Motor Stator Test System
Chroma 1920
-
Chroma Systems Solutions, Inc.
For electrical safety and quality testing functions of motor stator coils
-
Product
Insulating Oil Testers
US, A, AD Series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Confirms to IS 6792, IEC 156 • Tests insulating oils to IS, IEC, ASTM, etc.• Test voltage to 100kV• Motorized rise of test voltage: 2kV/sec • One piece construction with safety interlocked transparent hood covering test cell• Test voltage can be held at any desired level• kV meter continues to indicate breakdown voltage even after breakdown• Light weight: 36 kg only• Portable, rugged and with cover.
