Strain Gage Signal Conditioners
See Also: Strain Gages, Strain Gauges, Strain Gage Amplifiers
-
Product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
Signal Module
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Differential Active Probe, 1 GHz
DP0012A
Signal Probe
The Keysight DP0012A is the 1 GHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
PXI Breadboard Module, 1Slot, Dual 20-Pin GMCT
40-220A-811
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
CXA-m PXIe Signal Analyzer
M9290A
Signal Analyzer
Deploy a smaller microwave footprint, no trade-off in precision: Rely on fully specified performance up to 26.5 GHz in 4 slots Optimize your balance between speed, sensitivity and accuracy with the choice to operate in swept or FFT modes Perform fast calibrated stimulus response measurement with full-band tracking generator Smooth the transition between R&D, manufacturing, and maintenance: CXA-m is code compatible with benchtop X-Series signal analyzers and ESA spectrum analyzers
-
Product
FPD Tester Signal Module
A291800-03
Signal Module
The A291800 is an LVDS signal model that can be used with FPD Tester to provide LVDS panel standard signals and related controls for LVDS inspection.
-
Product
PXIe Vector Signal Generator: 1 MHz to 3 GHz or 6 GHz
M9381A
Vector Signal Generator
Choose your RF modulation bandwidth, 40, 100, or 160 MHz, and easily upgrade as test needs change Increase throughput with fastest RF frequency tuning and amplitude switching for high-speed automated test Save space with a compact solution for up to 8x8 MIMO with phase coherence Get up and running quickly with validated application-specific reference solutions Simplify signal creation with Keysight's Signal Studio and Waveform Creator
-
Product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWG
610110147
Signal Contact (ITA)
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWGThis contact primarily used in CASS applications.Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation Compliant
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 22-24 AWG
610138109
Signal Contact (ITA)
Primary mating contact 610138216. (May mate with other ITA contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2-ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.24
-
Product
20GHz Four Channel MW Benchtop Signal Generator
LSX2094B
Signal Generator
The LSX2094B is a 20GHz Four Channel Microwave Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
PXI Vector Transceivers
Vector Signal Transceiver
Get both signal generation and analysis in one PXIe module with real-time field-programmable gate array (FPGA)-accelerated measurements for faster throughput. The PXIe vector transceiver is perfect for manufacturing test of wireless devices, RF power amplifiers, and front-end modules.
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, 24 AWG Twisted Pair, Single Ended ( 3 Amps)
7-104424000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, 24 AWG Twisted Pair, Single Ended ( 3 Amps).
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-104422000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps).
-
Product
Signal, Patchcord, ITA, 72", TriPaddle, 24 AWG Twisted Pair, Single Ended ( 3 Amps)
7-103424000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", TriPaddle, 24 AWG Twisted Pair, Single Ended ( 3 Amps).
-
Product
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions
510109598
Strain Relief
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Single Ended (5 Amps)
7-124922000-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Single Ended (5 Amps).
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended
7-121974000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
Power Line Conditioner
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 1k
50-265-202
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
"Smart" Dynamic Signal Analyzers
EMX-4xxx
Signal Analyzer
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
Product
RF & Microwave Signal Generator
SMA100B
Microwave Signal Generator
The R&S®SMA100B RF and microwave signal generator delivers uncompromising maximum performance. It provides the purest output signals while maintaining the highest output power levels with the lowest harmonics, far outpacing the competition. As the world's leading signal generator, it can handle the most demanding module and system T&M tasks in the RF semiconductor, wireless communications, aerospace and defense industries.
-
Product
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-103922000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
-
Product
12GHz RF Analog Signal Generator Module
LS1291D
Signal Generator
The LS1291D, 12GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS1291D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS1291D is designed to meet today’s most demanding specifications, needed from the R&D benches to the production lines.
-
Product
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-121424000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG Twisted Pair White/Black, Single Ended (3 Amps)
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
Signal Module
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 68-Pin Male SCSI
7-124883666-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", QuadraPaddle, 68-Pin Male SCSI.
