-
Product
Alternate 2.64 (75.00) - 6.50 (184.00) General Purpose Probe
EPA-2J30-1
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
Battery Tester
700
-
The #700 has an internal loading capacity of 100 amps. It is a great tool for finding batteries that can’t stand up to the load of today’s automotive accessories. It will also test relative starter current draw and charging voltage.
-
Product
Specific Gravity Tester
LD-LSGT-A10
-
Specific Gravity Tester LD-LSGT-A10 determines the theoretical maximum specific gravity of bituminous mixtures in accordance to ASTM D2041 Standard Test Method for Theoretical Maximum Specific Gravity of Bituminous Mixtures (Vacuum process). Adopted with single chip machine technology to shake a loose asphalt mixture sample submerged in water. Vacuum is applied into the sample, to extract out the air bubble.
-
Product
Current Tester
MIG0624
-
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
-
Product
Hipot & Security Tester
-
Safety testers (also called hipot testers) ensure the safe use of test items in different working environments and under different operating conditions. There are a variety of solutions, depending on the tests required to meet the relevant industry standards. Many test units offer a combination of functionality and performance.
-
Product
Rust and Corrosion Testers
-
Liquefied petroleum gas copper corrosion tester, lubricating oil rust characteristics tester, rust characteristics and corrosion tester, copper strip corrosion tester
-
Product
General ELCB Testers
TEL1-x Series
-
Standard Electric Works Co., Ltd
The TEL1 is the Basic Test Equipment an Electrician cannot do without. TEL1 is a Dual Function Test Instrument utilized to Verify Electrical Wiring Connections and the Functioning of Earth Leakage / Residual Current Detectors devices by forcing the ELCB/RCD to trip.
-
Product
Instruments Transformers Tester
Calport 100 Plus
-
Calmet Smart Calibration Devices
Three phase instrument transformers and electricity meters tester class 0.1 or 0.2. It makes possible CT and PT testing on site or in the laboratory. We recommend a new replacement - TE30 Working Standard
-
Product
Insulation Tester
CENTER 360
-
4 Digits LCD Display, Auto Range For MΩ & Ω, 40 Segments Analog Display, Test Hold Function For Easy Operation, Automatic Zero To Null Lead Resistance
-
Product
Flexural Damage Tester
DRK242A-II
-
Shandong Drick Instruments Co., Ltd.
It is used to test the dynamic anti-torsion and flexural fatigue performance of coated fabrics.
-
Product
Display Tester
-
Yuyao City Yinte Neon-Electroscope Factory
This neon-electroscope is applicable for directly detection of 12-240V zero line indirect detection of DC.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Leak Testers
-
Vidac has installed various versions of Leakdown testers for products such as:ValvesSealsConduit fittingsExplosion-proof cases
-
Product
Ground Grid Tester
GGT Series
-
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.
-
-
Product
Yarn Count Tester
-
TESTEX Testing Equipment Systems Ltd.
Yarn Count Testing Machine, automatically calculates count systems used for sliver, roving and yarn, and can also be used for fabric yield. Yarn Count Tester consists of an accurate electronic balance with a capacity of 400g or 200g x 0.001g and built-in calculating program. Please contact us if you want to know more about yarn count test method.
-
Product
Spark Testers
-
Range of portable and hand-held AC spark testers, kits, accessories and electrodes which are all specifically configured to suit a range of test applications.
-
Product
Network Tester
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
Product
Capacitance & Tan Delta Testers / Tan Delta Tester
CDF 6000
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
CDF-6000 is fully automatic: It automatically ramps up to set test voltage, makes measurement, ramps down test voltage to zero and prints out test results.
-
-
Product
Electrical Tester
R580
-
Nidec-Read's R580 Electrical Tester provides an affordable test system for your bare board electrical test needs. You can easily integrate the R580 with your existing manual test fixtures or select from several fixture options from Nidec-Read. The R580 is supplied with opens/leakage test ability. In addition, you can include other advanced electrical test techniques.
-
Product
Compact Testers
-
Adaptronic wiring testers of the compact class are available as low voltage testers and also as high voltage testers, as KT version with display and keyboard and as NT version with the grafical user interface NT Control. With max. 5120 test points (NT 600) adaptronic wiring testers of the compact class are predestined for voluminous testing jobs and large products to be tested. Whether with adapter cables, test tables, test consoles or adapter consoles - the wiring testers of the compact class can also be used everywhere.
-
Product
sonic tester
PR-82
-
The PR-82 sonic tester has been modified for the automotive industry. This gauge is commonly used for measuring the thickness of cylinder walls, head ports, decks, tubing, body panals, and windshields. It also has the ability to scan the length of a part to find the the minimum thickness.The PR-82 is back-lit and the unit operates for up to 200 hours on a single set of batteries. It is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
Demulsibility Characteristics Testers
-
The Labodam Demulsibility Characteristics Tester is designed an dmade as per Test Methods for Demulsibility Characteristics of Petroleum Oils and Synthetic Fluids ASTM D1401
-
Product
Rockwell Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ Semi-automatic intelligent Digital Rockwell Hardness tester, you can automatically test the Rockwell hardness and surface Rockwell hardness measurement；◆ Automatic variable load, automatic loading, automatic unloading, automatic conversion, automatic measurement；◆ Friendly human-computer interaction，5.2“colorful LCD screen direct display test force,loading time,conversion value and indenter type etc； ◆ Automatically calculate and display the measured value, the maximum value, the minimum value, the average value and the hardness value deviation, the display shows the resolution 0.1HR；◆ There are functions such as hardness upper and lower limit settings, tolerance alarms, data graph analysis, average and (single point) batch measurement modes；◆ Software compensation function, the machine can be ± 3HR software compensation, no need to open the top cover for mechanical adjustment;◆ With automatic hardness conversion function, according to ASTM E140 conversion, no need to check the complex hardness of the table；◆ Multi-language features, can switch Chinese, English, German, Portuguese, Turkish, Czech, Korean and other languages；◆ Built-in 2000 single data storage function and 1000 group packet data storage function, can view a single data and data analysis；◆ Optional Bluetooth wireless printer to print the measurement data, no need to manually record and write test data；◆ Optional Softhard data analysis software and Bluetooth receiver on the test data for the computer into and analysis；◆ Support FexQMS measurement of large data analysis and control software to enhance the whole plant process control, reduce material loss.
-
Product
Installation Safety Tester
Eurotest EASI
-
EurotestEASI is the first member of a new line of Metrel's installation safety testers. Lightweight design and small dimensions make it ideal for prolonged use over a working day.
-
Product
Hydrogen Leak Tester
T8999
-
T8999 is a tool designed to meet the increasing need for easy and clean identification of the position of the leak on a piece being tested, therefore eliminating the need for methods such as water tank immersion or use of leak detecting sprays, which are harmful for the pieces which could develop rust or pieces that are difficult to accurately clean.
-
Product
GFCI Socket Tester
ST120
-
The Fluke ST120 GFCI Socket Tester checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120 will give you confidence on your next job.
-
Product
Power Supply Testers
-
Qmax Test Technologies Pvt. Ltd.
Power Supply Tester is an integrated package of hardware such as AC/DC Power Sources, DC Loads, Noise Measurement Unit, and DMM etc configured as per user applications, which makes it suitable for testing wide range of Power Supplies and provide economic solution for testing AC/ DC and DC/DC power supplies and converters. The Power Supply Boards that passed in the first level of screening for Go-No Go tests will undergo a second level testing. The second level of testing measures all the key parameters of the power supply such as line regulation, load regulation, efficiency etc and check whether the results are within the mentioned limit, if not declare the UUT (Power Supply Board Under Test) as a failed one.
