FMC
-
Product
Mezzanine FMC
FMC-520
-
Curtiss-Wright Defense Solutions
Through direct connection to a host FPGA, the FMC-520 provides a low cost, low latency path necessary for agile applications such as RADAR and EW. Conforming to the VITA 57 FMC standard, the FMC-520 simplifies developers’ integration of FPGAs and analog output into embedded system designs.
-
Product
FMC Mezzanine front panel
-
FPGA mezzanine card (FMC) front panels (according to Vita 57.1) | filler panels available
-
Product
Optical Transceiver FMC Modules
-
Sundance Multiprocessor Technology Ltd.
FMC Modules with Optical Transceivers
-
Product
DSP FMC Modules
-
Sundance Multiprocessor Technology Ltd.
FMC Modules with Digital Signal Processors
-
Product
Clock Distribution FMC Modules
-
Sundance Multiprocessor Technology Ltd.
Clock Distribution FMC Modules
-
Product
FMC Loopback Test Board
-
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
Product
3U OpenVPX FMC Carrier
VF360
-
Sundance Multiprocessor Technology Ltd.
The VF360 is a 3U OpenVPX module that leverages on Altera Stratix® V FPGA and Texas Instruments KeyStone Multicore DSP technology to provide an ultra-high bandwidth processing platform, ideally suited for computation and bandwidth intensive applications such as Radar, Networking, SIGINT, EW, SDR and Video.
-
Product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
-
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
-
Product
FMC-HPC ADC Board
FMC123
-
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
Quad 3.1 Gsps, 14-bit ADC FMC+
ADF-Q3114
-
The ADF-Q3114 is a VITA 57.4 compliant FPGA Mezzanine Card (FMC+) that converts four channels of up to 3.1 GHz analog input bandwidth. This digitizer provides unparalleled analog-to-digital conversion capability with the PCIe/VME/ VXS/VPX carrier board of your choice. The ADF-Q3114 is designed to be compatible with AMD FPGA platforms.
-
Product
FMC L-Band RF Receiver
-
Sundance Multiprocessor Technology Ltd.
The Creonic L-band RF receiver FMC card allows to receive RF signals between 925 and 2,250 MHz. It is ideally suited for satellite communication with standard satellite dishes since it includes a DiSEqC driver IC for LNB controlling. The board allows to build receivers with symbol rates of up to 100 Msymbols/s. Due to the low-pin-count (LPC) FMC connector it can be used with any FMC carrier board that supports VADJ=1.8V. The card will be available from Q2/2017.
-
Product
FMC Quad ADC 16-bit @ 1 GSPS and Quad DAC 16-bit @ 2.8 GSPS
FMC231
-
The FMC231 is an FPGA Mezzanine Carrier (FMC) per VITA 57 specification. The board has quad ADC (the ADC chips are dual channels) and quad DAC (the DAC chip is quad channel). The FMC231 utilizes TI ADS54J60 (option for ADS54J69) providing 16-bit conversion rates of up to 1.0 GSPS and a DAC DAC39J84 providing 16-bit conversion rates of up to 2.8 GSPS.
-
Product
4-Channel DAC FMC Module
FMC204 – HPC
-
Sundance Multiprocessor Technology Ltd.
The FMC204 is a quad channel DAC FMC. The FMC204 provides four channels of 16-bit D/A @ 1 GSPS enabling simultaneous sampling at a maximum rate of 1 GSPS. The sample clock can be supplied externally through a coax connection or supplied by an internal clock source (optionally locked to an external reference). Additionally a trigger input for customized sampling control is available. The FMC204 daughter card is mechanically and electrically compliant to FMC standard (ANSI/VITA 57.1).
-
Product
PCI Express FMC Carrier
RFM-BSC5GT7H1
-
Sundance Multiprocessor Technology Ltd.
The RFM-BSC5GT7H1 is a PCI Express short sized FMC carrier board with Cyclon V FPGA (Altera), which is designed mostly for low cost, high-performance data acquisition.
-
Product
GMSL II Output FMC Module with MAX96705
TEF0010-01
-
Sundance Multiprocessor Technology Ltd.
FMC module with Xilinx Artix-7 FPGA and 4 x 16-Bit GMSL serializers.
-
Product
3U VPX VITA 66.5 FPGA board with FMC+ Site
IC-FEP-VPX3f
-
Based on the latest Xilinx Kintex® UltraScale™ 20nm FPGA family, the IC-FEP-VPX3f is the first VITA 66.5 compliant FPGA board available. It is the perfect solution for applications requiring DSP-intensive processing in a 3U VPX form factor.
-
Product
FPGA/FMC Carriers
-
Our AMC FPGA modules feature Altera Stratix IV, Altera Stratix V, Xilinx Virtex-5, Xilinx Virtex-6, Xilinx Zynq, Xilinx Artix, Xilinx Virtex-7 and Xilinx Kintex-7 FPGAs. We also offer a range of carriers that can accommodate standard FMCs featuring FPGAs from Altera and Xilinx, including the new Xilinx UltraScale family.
-
Product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
-
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
-
Product
PCIe FPGA Carrier For FMC, Virtex-7
PCI516
-
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
Product
FMC Card with DisplayPort Input and Output
TEF0007-02A
-
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
-
Product
PC104Z with FMC Board
PC104Z
-
Sundance Multiprocessor Technology Ltd.
PC104Z is based on the Xilinx Zynq UltraScale+ MPSoC family. This hardware is in PCIe104 form factor and adheres to its latest specification. It offers 4 Gen 2.0, x1 lane PCIe interfaces through a switch which allows 4 PCIe104 cards to be connected to the ARM on the Zynq which acts as the host. The board also offers 2 Gen 4.0, x4 lane PCIe connected to the PL parts which can act both as host and end points. The additional interfaces offered by this card can be seen under the Features tab.
-
Product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
-
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
Product
FMC I/O Module
FM192
-
Sundance Multiprocessor Technology Ltd.
The FM192-R board is designed to fan out the FMC-LPC connector I/Os to four DB9 connectors and one SEIC connector. The FM912-R provides wireless connectivity via WiFi + BLE and 4G + GNSS/GPS modules. 3x antenna connectors (2x for the 4G + GNSS/GPS and 1x WiFi + BLE) are provided for connecting 3x external antennas. Furthermore, the FM192-R provides an IMU sensor, CAN BUS, humidity and temperature sensor and Audio I/O.
-
Product
Quad QSFP28/QSFP+ FMC+ Module
-
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
Product
5 Channel DAC FMC Module
DACNF05 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF05 is a five channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A. A single-ended external input or output clock is provided. The direction of the clock is programmable from the FPGA of the FMC carrier board.
-
Product
Mezzanine FMC
FMC-516
-
Curtiss-Wright Defense Solutions
The FMC-516 provides the low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of data delivered to the FPGA host through the FMC-516.
-
Product
FPGA Mezzanine Card
FMC172
-
The Abaco FMC172 wideband low latency FMC module is based on the latest high performance ADC device from Texas Instruments and DAC devices from Teledyne-E2V. It is the fastest ADC Abaco offers with LVDS interfaces, delivering up to 6.4 GSPS ADC on a single channel (or two channels @ 3.2 GSPS) and a single channel DAC at up to 6.0 GSPS, making it among the fastest low-latency devices available on the market. The combination of the FMC172's >6.0 GHz bandwidth, its high sample rate and low latency is ideal for advanced Digital RF Memory (DRFM) systems.
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
FPGA Mezzanine Card
FMC134
-
The FMC134 provides customers with a high bandwidth and high channel count I/O solution that is ideal for multi-channel receivers in a wide range of applications.With four 12-bit analog-to-digital channels up to 3.2GSPS or two analog channels up to 6.4GSPS, the FMC134’s design is based on the Texas Instruments™ ADC12DJ3200 and is mechanically and electrically compliant with the FMC+ standard (VITA 57.4), the next generation of small form factor expansion I/O for high performance FPGA-based systems.
