Switch Matrix
See Also: Switching Matrices, Matrix, Switch Matrices, Crossbar
-
Product
High-Power PXI Switch Matrix Modules
-
These high-power PXI switch matrix modules provide higher current and power ratings than the high-density switch versions. These modules are designed for the switching of AC or DC loads or for controlling large relay or solenoid systems. The solid state relay matrices occupy two PXI slots and are suitable for automotive and aerospace test applications.
-
Product
4x8 2 Wire USB Modular Switch Matrix
U2751A
-
The U2751A USB Modular Switch Matrix offers a flexible connection path between the device under test and the test equipment, thus allowing different instruments to be connected to multiple points on the device under test at the same time. This instrument is able to support measurements at a high bandwidth of up to 45MHz. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity
-
Product
High Density Switch Matrix PXI Card
GX6616
-
The GX6616 is a 6U PXI switch matrix board that provides either differential or single-ended multiplexing capability through software commands, along with six groups of 2 x 16 that may be used in various configurations.
-
Product
2X8 PXIe Switch Matrix, 300 KHz to 9 GHz
M9165B
-
M9165B 2X8 PXIe switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution.
-
Product
2X16 PXIe Switch Matrix, 300 KHz to 6.5 GHz
M9164A
-
M9164A 2X16 PXIe switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution.
-
Product
Low-Density PXI Switch Matrix Modules
-
Our low-density PXI switch matrix modules are a cost-effective solution for applications that require relatively small matrices in the PXI format. These low-density switch matrices can be expanded by connecting together multiple modules, however, we recommend that users look at the higher density switch matrix modules that involve less user configuration. Reed relay versions use high quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. For general purpose applications that also require higher power handling, the range of electro-mechanical relays provides an ideal solution.
-
Product
Low-leakage Switch Matrix Family
-
Conducting all the parametric measurements necessary for the numerous test structures on a semiconductor wafer can be a time-consuming and expensive process. With the cost of end-user devices continuing to drop, even laboratory characterization environments must reduce the cost of test. Until now engineers and scientists working on current and future semiconductor process technologies were faced with a difficult choice: either use a semiconductor parameter analyzer with positioners on a wafer prober, which limits the ability to perform automated test, or use a switching matrix and probe card, which reduced the analyzer's measurement resolution. Utilizing a switching matrix with a semi-automatic or fully-automatic wafer prober enables characterization tests to be automated, eliminating the need to have an operator manually reposition the probes each time a new module needs to be tested. This reduces both test time and cost. Due to the many price/performance points available, Keysight's switching matrix solutions provide the flexibility to choose exactly what your testing needs require, without overspending.
-
Product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
-
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
Product
RF Switch Matrix
-
Switch Matrices are offered in Blocking, Non-Blocking, and Super Non-Blocking configurations in mechanical housing packages of 1U-10U. Completely customizable control (USB, 10/100 Base-T) and expandable in blocks of 8 by 8 and 64 by 64 in a single unit, multiple units up to 256 by 256.
-
Product
2X16 PXIe Switch Matrix, 300 KHz to 9 GHz
M9164B
-
M9164B 2X16 PXIe switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provide a switch based multiport VNA solution.
-
Product
2X16 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9164A
-
P9164A 2X16 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving a larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others
-
Product
2X16 USB Solid State Switch Matrix, 300 KHz To 9 GHz
P9164B
-
P9164B 2X16 USB solid state switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
-
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
PCI 8x9 RF Coaxial Matrix Card 50Ω SMB
50-725A-511
-
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
LXI Dual 24x8 50 Ohm HF Matrix BNC
60-760-006
-
The 60-760 is a Dual 24x8 HF Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50 Ohm and uses SMB signal connectors, or with a larger case size, BNC Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-760-002 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
Product
PXI Matrix Switch Module
-
PXI Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
PXI/PXIe Switched Guard Matrix, 8x4
40-590-102
-
The 40-590-102 (PXI) and 42-590-102 (PXIe) are modules that provide a switched guard 8x4 matrix solution with up to 1012 Ω channel to channel and channel to ground isolation.
-
Product
PXI-2503 , 48‐Channel, 1-, 2-, or 4-Wire, Electromechanical PXI Multiplexer Switch Module
777697-01
-
48‐Channel, 1-, 2-, or 4-Wire, Electromechanical PXI Multiplexer Switch Module—The PXI‑2503 is a PXI switch module that you can configure as a multiplexer or matrix switch by using different terminal block accessories. It uses electromechanical relays with low thermal offset for accurate measurements and offers a 1,024‐step scan list for deterministic scanning.
-
Product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
LXI Single 24x8 50 Ohm HF Matrix SMB
60-760-001
-
The 60-760-001 is a Single 24x8 HF Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50Ω and uses SMB signal connectors, or with a larger case size, BNC Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
-
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
ASA240
-
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
PXI 4-Slot BRIC Matrix, 87X8 2A 2-Pole (3 Sub-cards)
40-565B-002-87X8
-
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
Product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
-
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
Product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
-
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-728-002-L
-
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Switching Test Set
U3020AS26
-
The Keysight U3020AS26 is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
Product
PXI BRIC8 FIBO Matrix Dual 140x4 3pin brkout
40-592A-107
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI-2534, 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-34
-
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2534 is a high-density 8x32 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2534 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
DVI Video Matrix Switch with Audio Option up to 32x32
SM-nXm-DVI-LCD
-
The VEEMUX® DVI Video Matrix Switch routes video from up to 32 single link digital DVI video sources (computers, DVD players, satellite receivers, etc.) to up to 32 displays (LCD monitors, Plasma screens, DLP HDTVs, projectors, etc.) and stereo audio speakers (with audio option).
