Bus Translator
Bus Converters are used as an interface between separately powered components of a logic system.
See Also: Bus
-
Product
34-Pin RTSI Female to 34-Pin RTSI Female Ribbon Cable
776249-02
BUS Cable
RTSI Bus Cables for 2 PCI or AT/ISA Devices
-
Product
Bus Extenders for VXI and PXI
Bus Extender
Select from our variety of bus extender and carrier modules.These products were formerly sold under the Racal Instruments brand name.
-
Product
PXIe, X4, MXI-Express Daisy-Chain Copper Interface, PXI Bus Extension Module
781820-04
Bus Extender
PXIe, x4, MXI-Express Daisy-Chain Copper Interface, PXI Bus Extension ModuleThe PXIe-8374 allows you to create multichassis PXI systems that interface to the same computer. You can use the PXIe-8374 to daisy chain up to eight PXI chassis to the same system computer, which can be a PXI Controller or a PC connected with a Device for PXI Remote Control. You can also extend the PXI system by connecting RAID Arrays, Software Defined Radio Devices, and Software Defined Reconfigurable Radio Devices.
-
Product
Module Extender For 34980A
Y1132A
Bus Extender
Extends the backplane of the 34980A switch/measure unit outside the instrument’s frame for easy servicing of plug-in modules
-
Product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
Bus Extender
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
Product
34-Pin RTSI Female to 34-Pin RTSI Female Ribbon Cable
776249-03
BUS Cable
RTSI Bus Cables for 3 PCI or AT/ISA Devices
-
Product
PXI Bus Expanders
MXI-4E Series
Bus Extender
The MXI-4E PXI Bus Expander allows for direct control of PXI systems from a PCI or PCIe slot in a desktop computer or server. MXI-4E interface cards can also be used for linking multiple PXI chassis. MXI-4E technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
-
Product
Level Translators
-
Renesas offers a 6-channel bidirectional, auto-direction sensing, level translator that simplifies the interface between two logic ICs operating at different supply voltages.
-
Product
Precision Translation Stage
M-405 · M-410 · M-415
-
Physik Instrumente GmbH & Co. KG
M-400 series translation stages are compact, leadscrew-driven stages with a travel range of 50, 100 and 150 mm. All models are equipped with low-friction leadscrews for excellent resolution and repeatability. Precision crossed roller bearings guarantee 2 m/100 mm straightness of travel. The stage base is precision ma-chined from high-density, stress-relieved aluminum for exceptional stability and minimum weight.
-
Product
Camera Link Translators
CLT-303
-
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
-
Product
Bus Expanders
-
PXI Bus Expanders and PXI Interface Cards for both PXI and PXI Express interfaces.
-
Product
High-Accuracy Translation Stage
M-605
-
Physik Instrumente GmbH & Co. KG
M-605 series translation stages are designed to meet the most demanding positioning requirements in applications where space is limited.They feature a space-saving design with the ballscrew side-by-side to the motor and an extremely flat, precision-machined base of high-density, stress-relieved aluminum providing exceptional stability and minimum weight.
-
Product
Bus Analyzer
FireSpy430b(T)/830b(T)
-
The FireSpy430b(T) and FireSpy830(bT) bus analyzers are the single bus models in the 4th generation of IEEE-1394 analyzers from DapTechnology. Based on the industry leading FireSpy810 the all new and enhanced architecture of the FireSpy430b(T)/830b(T) have again defined a new reference in IEEE-1394 test equipment! They comprise a significantly more powerful on-board processor, more memory and improved connectivity to the host.
-
Product
Bus Analyzer
FireSpy® 6432bT/6832bT
-
The FireSpy6432bT and FireSpy6832bT bus analyzer are the world’s only 6-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy6432bT/6832bTare the most advanced 1394 test equipment in the market. The FireSpy6432bT/6832bT in fact combine six FireSpy analyzers in one single instrument. They comprise a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
Bus Analyzer
Goebelyzer
-
Our Goebelyzer analyzer systems offer unparalleled insight into bus data and are used in flight test, system simulation, LRU design, verification and manufacturing test. Supported Interfaces Arinc 664, ASCB-D, Honeywell Flight Controls P2P, Arinc 429, CAN2.0b, Mil Std 1553, RS 422 SDLC/Async, ADC
-
Product
Miniature Translation
M-311 – M-318
-
Physik Instrumente GmbH & Co. KG
The M-310 series of translation stages are our smallest micrometer-driven positioners. The carriage is spring preloaded against the micrometer tip for elimination of backlash. M-310 series stages are available in one-, two- or three-axis configurations. The latter consists of a two-axis stage, an angle bracket and a one-axis stage. Please note that an XY unit cannot be separated into two one-axis stages. The vertical stage in the M-313 XYZ assembly supports the load through the micrometer spindle (not the preload springs) providing excellent stability.
-
Product
Vector Translation Platform
Solstice-TDS
-
New, casual, or advanced users can be productive right away with Solstice-TDS test engineering centric GUI. WaveMaker+ makes simple vector translation tasks simpler, and massive enterprise multi-group pattern conversion projects easy to coordinate and manage in a flow-based use model.
-
Product
Bus Analyzer Software
Bus Hound v. 7
-
Experience the power of a software bus analyzer capturing I/O, low level protocol and send commands to devices.
-
Product
Bus Analyzer Software
AltaView
Analyzer
Alta’s Windows avionics analyzer product, AltaView, provides the most modern technologies for MIL-STD-1553 and ARINC-429 network activity and data analysis. Win XP/Server/7/8/10 Compatible and VMware with ENET/NLINE Ethernet. Ideal for Cybersecurity Testing.
-
Product
Bus Analyzer
FireSpy® 9433bTRGD/9833bTRGD
-
The FireSpy9433bTRGD and FireSpy9833bTRGD bus analyzer are world’s only 9-bus IEEE-1394 protocol analyzer meeting harsh flight line and in-field testing. Based on the 4th generation FireSpy analyzer architecture the FireSpy9432bT/9832bT but has been incorproated into an enclosure designed to meet MIL-STD-810 requirements.
-
Product
Bus Switches
-
Bus Switches are devices that enable system architecture to be reconfigured. This reconfiguration is mostly accomplished in the test environment and includes but is not limited to simulation of missile firing and switching in or out a new section of bus interface.Excalibur Systems is the only manufacturer of devices (ESI-R24/27/28) that contain their own TTL driver circuitry that allows them to be directly driven from a computer.
-
Product
8 Channel NIM-ECL/ECL-NIM Translator
V538A
-
The Model V538 A is a 1-unit wide VME module housing 8 independent logic level translators. Each of the 8 channels accepts a NIM or ECL signal and provides two NIM and two ECL outputs (OUT 0÷7 A, B). The NIM and ECL inputs of each channel are ORed prior to fan-out.
-
Product
34-Pin RTSI Female to 34-Pin RTSI Female Ribbon Cable
776249-04
BUS Cable
RTSI Bus Cables for 4 PCI or AT/ISA Devices
-
Product
ASCB Bus Analyzer And Generator
DataTap-10
-
Innovative Control Systems, Inc.
The DataTap 10 is our most advanced ASCB Bus Interface Product available that receives and records all versions of ASCB including ASCB-A, B, C, D, and Enhanced ASCB. The unit can also optionally transmit on ASCB-D and Enhanced ASCB for simulation purposes. The device is available in 2 configurations. We offer the standard DataTap-10 in a black anodized aluminum case and for Flight Test we offer a ruggedized version. Both of these are listed below.
-
Product
Quad 4 Fold AND/OR/MAJ, NIM-TTL TTL-NIM Translator
V976
-
The Mod. V976 is a 1-unit VME module housing four 4-input Coincidence Fan in/Fan out and NIM – TTL / TTL – NIM adapter sections. Each section features 4 inputs and 4 outputs on LEMO 00 connectors and can operate as a 4 channel level translator or as AND/OR gate.
-
Product
PCI Smart Bus Extenders
PCIEXT-64UB - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
