PCMCIA Adapters
Adapters that fit in the PCMCIA slot in notebook computers. Different adapters have different functions but they all add connectivity possibilities. (beststuff.co.uk)
-
Product
Mounting Flange Kit, G20/G20x Slide Mount, 6.75" Series Adapters, For Pickering 40-923
310113644
Mounting Kit
A mounting flange kit for the G20/G20x series receiver for mounting in a Pickering 40-923 Chassis.
-
Product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
Product
I2C Adapter
RS485
-
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
Product
X.25 Adapters & XOT
FarSync X25 T4Ee
-
This top of the range FarSync X25 T4Ee PCIe card provides 4 high performance X.25 communications lines handling many different line signalling modes. A PCI version is also available.
-
Product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 2 Slots, Texas Instruments PCI1520 Chipset
P222-TI1520
-
The PCI to 2-slot PCMCIA/CardBus PC-Card adapter supports 3.3V & 5V PC-cards (PCMCIA/Cardbus) simultaneously. Hot-swap PCMCIA/Cardbus PC-cards without powering off the system. 2 independent icons in MY COMPUTER. The adapter is quick & easy to install, allowing PC-card devices to be used in any desktop or tower PC.
-
Product
PCI to PMC Adapter / Carrier
PCIBPMCx2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
Product
Test Adapter
cPCI/VME/VME64x
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz
Q281B
-
The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
DisplayPort To DVI Adapter For Embedded Controllers
Y1261A
-
Achieve backward compatibility between DisplayPort and a DVI computer monitor.
-
Product
RS232 I2C Adapter
12C Master
-
*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
-
Product
Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 110 GHz
11920B
-
The Keysight 11920B precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms and frequency range from dc to 110 GHz.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11901A
-
The Keysight 11901A is a 2.4 mm male to 3.5 mm male metrology-grade adapter with dc to 26.5 GHz operation.
-
Product
Wireless Adapters
-
A device that can be plugged into a USB port to enable wireless access from a computer to an external Wi-Fi device, as a mobile phone, or to the Internet, via high-speed broadband, or to enable wireless connectivity in a printer or other peripheral.
-
-
Product
Adapter Kit, 3.5 mm to Type-N, DC to 18 GHz
11878A
-
The Keysight 11878A adapter kit provides the RF components generally required when an SMA or 3.5 mm device needs to be measured with a network analyzer type-N configuration. This kit includes four type-N to 3.5 mm adapters for both male and female connectors.
-
Product
XMC-PCIeStor, High Speed PCIe Quad M.2 SSD Adapter
9303
-
The 9303 is an air or conduction cooled, extended temperature XMC card with 4 M.2 SSD sites for multi-terabyte storage. Onboard Gen2 PCI Express (PCIe) switch connects one 4-lane upstream PCIe port to four 1-lane downstream ports.
-
Product
Coaxial Waveguide Adapter, Type-N (f), 8.2 to 12.4 GHz
X281A
-
The Keysight X281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
XMC-to-PCI Express Adapter
7988
-
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
32-bit / 33 MHz PMC to PCI Adapter
4933
-
This PMC to PCI Adapter product from Technobox permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
RF Adapters
SMPM Adapters
-
a type of blind-mate, push-on connector that is similar to SMP connectors.
-
Product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
-
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
Product
NI-5734, 120 MS/s, 16-Bit, 4-Channel Digitizer Adapter Module for FlexRIO
781659-04
Digitizer
The NI‑5734 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples four channels at 120 MS/s. You can use the NI‑5734 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5734 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Test Port Adapter Set, 2.4 Mm To 3.5 Mm
85130F
-
The Keysight 85130F test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector designed for connecting to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.
-
Product
EBIRST 78-pin D-type To 68-pin Female SCSI Adapter
93-006-222
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
NI-5741, 16-Bit, 1 MS/s, 16-Channel Signal Generator Adapter Module for FlexRIO
782864-01
Signal Generator
The NI‑5741 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5741 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5741, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
-
Product
PCB Adapter, ITA, VTAC, to (6) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1)
510171103
PCB Adapter
This fully loaded loaded SIM ITA module connects 34 slots of VTAC inserts to (6) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) connectors. Ships fully assembled.
-
Product
Manual Test Adapter With Rigid Needles
-
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
Product
8-Port RS-422 Async Serial Communications Adapter PMC
2316
-
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS422 signaling levels
