Jitter
Unwanted signal deviation.
-
Product
Ultra-low Jitter Clock Synthesizer
SLC Series
-
Noise eXtended Technologies S.A.S.
The SLC is a very affordable single or dual clock 7 GHz synthesizer that exhibits outstanding phase noise and jitter performance in a very small package.
-
Product
Jitter And Eye Diagram Analysis Tools
DPOJET
-
DPOJET is the premiere eye diagram, jitter and timing analysis package available for real-time oscilloscopes.Operating in the Tektronix DPO7000, DPO70000 and DSA70000 Series oscilloscopes. Jitter and Timing Analysis for Clocks and Data Signals. Real-Time Eye Diagram (RT-Eye™) Analysis*1. TekWizard™ Interface for One-Button and Guided Jitter Summaries.
-
Product
RF & Microwave Modules And Instruments
-
SHF Communication Technologies AG
In digital high speed test and measurement, a perfect clock signal is crucial for the generation of low jitter reference test signals. A SHF Synthesized Signal Generator (Synthesizer) used as a clock source can operate over several decades of frequency and is an essential part of any high speed test and measurement environment.
-
Product
Infiniium V-Series Oscilloscope: 16 GHz, 4 Analog Channels
DSAV164A
Oscilloscope
16 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Adjustable Length Linear Backlight, 300 mm to 2100mm
Vitech A1905
-
Modules A1905 are designed for pulsed or continuous illumination of objects in machine vision systems. The time of ignition (90%) and blanking (10%) of the module is less than 1 μs with jitter of the front (jitter) no more than 2 μs, which allows the modules to be used for exposure with "slow" cameras.
-
Product
Multiplexer 2:1 With De-Emphasis 32 Gb/s
M8062A
Multiplexer Module
R&D and test engineers who need to characterize serial interfaces of up to 32.0 Gb/s can use the M8061A 2:1 Multiplexer with optional de-emphasis to extend the rate of J-BERT M8020A and J-BERT N4903B pattern generator. For the most accurate receiver characterization results, the M8061A provides four calibrated de-emphasis taps, which can be extended to eight taps, built-in superposition of level interference and Clock/2 jitter injection. The M8061A is a 2-slot AXIe module that can be controlled via USB from the user interface of J-BERT M8020A as well as N4903B.
-
Product
Clock & Data Recovery
-
Macom Technology Solutions Holdings Inc.
Macom offers a series of high-performance, flexible, clock-and-data recovery (CDR) devices to remove the jitter from signals in high data rate systems. Our family of CDRs spans from 10Gbps to 100Gbps per lane in multitude of configurations including single lane and multi-lane devices, standalone CDRs and integrated combo devices with TIA and laser drivers. This wide portfolio of configurations offers customers design flexibility and cost-optimization in systems for Ethernet and OTN based network infrastructure markets and extending to high performance computing, storage-area-networking (SAN), industrial and aerospace applications.
-
Product
Linear Signal Splitters
-
Advanced Science and Novel Technology, Co., Inc.
DC to 25GHz broadband linear signal splitterOne differential CML-type input port and four phase-matched differential CML-type output portsDifferential input linearity range up to 1000mV p-pDifferential gain of approximately -1.5dBLow jitter and limited temperature variation over industrial temperature rangeSingle +3.3V or -3.3V power supplyPower consumption: 1.35WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 44-pin package
-
Product
Universal Encoder Checker
Talon
-
Test digital Encoders (5, 12, & 24 Volts)Troubleshoot Digital Read Outs (DRO's)Count / verify Pulses Per Revolution (PPR)Adjust Encoder after cleaning or repairTest for weak or dead signal outputTest for intermittent phase jitter
-
Product
PCI Bit Synchronizer
LS-40-P
-
The Lumistar LS-40-P PCI Bit Synchronizer provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a consistent product with high reliability and long-term stability. The LS-40-P PCI Bit Synchronizer consists of the LS-40-DB Bit Synchronizer Daughterboard shown below mounted on a PCI carrier board.
-
Product
Infiniium V-Series Oscilloscope: 16 GHz, 4 Analog Channels
DSOV164A
Oscilloscope
16 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Phase Locked Loop (PLL) Synthesizer & Translation Loop
-
ADI’s industry leading phase locked loop (PLL) synthesizer family features a variety of high performance, low jitter clock generation and distribution devices. The extensive, ever growing family includes over 100 products, optimized for high data rate, low jitter clocking applications. The portfolio features PLLs, PLL/VCOs, and distribution chips, designed for clocking applications where synchronization, clock distribution, and phase noise performance are all vitally important.
-
Product
DCA Equivalent-time Sampling Oscilloscopes
-
Equivalent-time (sampling) oscilloscopes are also known as digital communication analyzers (DCA). They are designed to visualize and analyze the analog properties of high-speed signals used in data center and wireline telecom applications. The Keysight DCA platform features a wide variety of optical, electrical, and TDR/TDT modules, compliance applications, and a common FlexDCA user interface to ensure more efficient testing in both R&D and manufacturing. Due to an ultra-low jitter and low-noise acquisition system, the Keysight DCA series provides industry-leading measurement accuracy for high-speed digital designs including 400G/800G Ethernet and Fibre Channel.
-
Product
Transimpedance Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband transimpedance amplifier for low noise receiver side applicationsFeatures automatic input offset control and a peak detector8GHz of analog bandwidth for limiting of input data60dB of transimpedance differential gain15pA/sqrtHz of input referred noise density (0.1 to 10GHz)CML output interface with 50 termination and 225mVp-p single-ended swingSingle +3.3V power supplyPower consumption: 250mWExhibits low jitter and limited temperature variation over industrial temperature rangeUnpackaged bare die
-
Product
Infiniium V-Series Oscilloscope: 33 GHz, 4 Analog Channels
DSAV334A
Oscilloscope
33 GHz analog bandwidth4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
MIL-STD-1553 A, B Simulator/Analyzer/Tester
CIC201
-
MIL-STD-1553 A, B Simulator/Analyzer/Tester - CIC201B VME/VXI B Size Interface, CIC201C VME/VXI C Size Interface - The CIC201 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
Performance Testing
-
All of Xena’s products can be used for performance testing. This typically includes measuring:*the volume of data successfully delivered between two points, usually measured in bits or packets per second*how long it takes data packets to travel between two points in a network or a device, also known as latency*variations in latency – also known as jitter – due to network congestion or other factors*how many data packets fail to reach their destination*if data packets are delivered in a different order from that in which they were sent
-
Product
Pulser / Sampler Core
-
Furaxa has researched, developed, and characterized a novel monolithic arrayable pulse and sample aperture generation technology. Recent results include demonstration of sub-10ps pulse/aperture generation at repetition rates up to 3 Billion Pulses/Samples Per Second (BPPS) with jitter that is estimated at sub-10fs. Further, simulations in a number of InP DHBT processes exhibit sub-3ps 20BPPS performance. The IP is process-independent, and has been achieved in CMOS SOI, InP HBT, SiGe and GaAs so far. Please contact us regarding your specific foundry and technical requirements: The company currently licenses the sampler/pulser technology for use by application and market, and is interested in discussing how the technology can enable our partners' applications. A short list of characterized Pulser/Sampler Cores is given below.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
Function/Arbitrary Waveform Generators
SDG5000 Series
-
Siglent Technologies invented the pulse generator algorithm EasyPulse, which is found in the SDG5000 waveform generators. Based on this new technology, the SDG5000 is capable of generating a pulse signal with low jitter, fast rising and falling edge (frequency independent effect), small duty cycle, edge and pulse width can be a wide range of adjustment.
-
Product
Infrared Video Processing
-
*Edge Enhancement improves the apparent sharpness of an image by boosting the contrast of edges in the imagery *Electronic Image Stabilization compensates for jitter in a video sequence, providing stabilized video output and remaining responsive to intentional user panning*Auto-Focus automatically adjusts the lens focus to its optimal in-focus position *Electronic Zoom uses interpolation to produce an enlarged image on the video display *Non-Uniformity Correction compensates for detector-to-detector non-uniformity to provide a well-calibrated image output
-
Product
Signal Generator, 20MHz, 2 Channel, Arb.
33512B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
Signal Generator, 20MHz, 2 Channel
33510B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
TTESync For VxWorks 653
-
TTESync is a synchronization component that allows tight synchronization of VxWorks 653 partitions to the fault-tolerant system-wide cycle time of the TTEthernet communication network. All partitions executed on different modules can be “pinned down” within the overall system cycle time, thus enabling the lowest latency and minimum jitter in message exchange among distributed functions. At system level this results in clean layering, well-understood functional interactions and simpler application design, testing and system integration. System architects can reduce system complexity and further optimize system size, weight, power (SWaP) and life-cycle costs.
-
Product
Computer-Based Instruments
GT210PCIe
-
with the GT210PCIe you can determine any frequency to 0.01 part per million (eight digits) in just 1 mS, and resolve each time measurement to 8pS. Couple that with 2300 measurements per second, one of the fastest rates available and you can acquire more data in a single second than a typical GPIB counter can in one minute! Faster measurements and higher resolution, along with built-in statistics functions give you a more thorough analysis of your signal. Standard deviation, peak to peak jitter, or a graph of the measurements are available at the push of a button.
-
Product
Signal Generator, 20MHz, 1 Channel, Arb.
33511B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
28/45 GHz Quad Optical Channel DCA-M
N1092D
Oscilloscope
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, and fast sampling rates for high throughput.
-
Product
Clock Generator
CG-1000
-
High-precision OCXO is used for the internal clock.Master clock generator with advanced features such as jitter management and glitchless relock.
-
Product
Mixed Signal Oscilloscope: 25 GHz, 4 Analog Plus 16 Digital Channels
MSOV254A
Oscilloscope
25 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
AFDXEnd System
A664 Pro (PMC)
-
The AFDXEnd System A664 Pro board supports speeds up to 100 Mbit/s and is certifiable to civil aerospace standards. This PMC card supports rate-constrained traffic shaping to ensure bounded latency and jitter for Deterministic Ethernet networking, as described in the ARINC 664 part 7 standard. The network board can be used for production system integration and provides redundancy management as well as an IP/UDP profiled communication layer fully implemented in hardware.
