High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. Also known as: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
Product
HV AC Voltage Test Systems
-
Fivestar HV Testing Equipment Co., Ltd.
FSHV offers three different types of AC voltage test systems, the conventional type is AC test transformer design, mainly for testing objects of medium & low capacitance products, particularly for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (like inductive voltage transformers). Another is AC resonant test systems, according to series resonance circuit XL=XC (2πfL=1/2πfC), by setting F frequency of power supply or L inductance of reactor, generate a pure sinusoidal waveform of the test voltage, and the required input power is only 1/Q. Variable frequency type operates in a frequency range from 20Hz to 300Hz, ideal for field commissioning test of power cables and GIS/GIL. Variable inductance type outputs continuous AC voltage of power frequency (50/60Hz), mainly for factory testing of high and ultra-high voltage cables, power transformers, GIS, etc.
-
Product
The Golden STM
-
*Golden (chemically resistive) vibration isolated STM body with implemented preamplifier*Computer with PCI board based SPM controller *Anfatec Scan & Anfatec Present*19“ STM controller (extra low noise 24 bit converters)*HV display for z-direction*High voltage amplifiers for the x-y-tube scanning*Optional: PC controlled bi-potentiostat and electrochemical cell
-
Product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
-
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-FF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly. 9-Pin D-Type Male To Unterminated With Ferrules, 1m, HV
40-972-009-1m-MU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot breakwhen they are terminated.
-
Product
LXI High Voltage Switching - 3-Bank, 1-Pole, 6:1 Multiplexer Plugin Module
65-231-910-HI
Multiplexer Module
The 65-231-910-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Horn Antenna
-
Horn antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in electric assets like GIS and GIL or MV and HV power transformers. It is a broadband antenna with a flat response which makes Horn antenna suitable in a number of different applications. It has been optimized to operate in a frequency range suitable for PD activity monitoring and it was designed to provide maximum sensitivity and high gain.
-
Product
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe
T3HVD1500-200
Differential Probe
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe.
-
Product
Proving Unit& Calibrators
-
Shanghai Beha Electronics Co., Ltd.
Calibration box is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.
-
Product
Signal Light for Hipot Testers
LX-signal light-HV1
-
2-color indicator light, red, green.With the help of the signal light tower, you can visualize potentially high voltage.
-
Product
LXI High Voltage Switching - 10xSPST Plugin Module
65-233-904-HI
Switch Module
The 65-233-904-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Interface and Isolation
-
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
Product
High Voltage Differential Probe
DP750-100
-
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
Digital / Analog Converter
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-133-HI
Programmable Resistor Module
The 40-230-133-HI (PXI) and 42-230-133-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
4 x 8 Two-Wire Matrix Module for DAQ970A and DAQ973A
DAQM904A
Matrix Switch Module
4 x 8 Two-Wire Matrix Module. 32 two-wire crosspoints with high switching voltage capability of up to 300 V and current capacity of up to 1 A.
-
Product
High Voltage Insulation Tester Module
DP-cPCI-5586
-
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
Product
High Voltage 50 Pin D-Type Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-711-HI
Multiplexer Module
The 65-231-711-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors.
-
Product
DC High Voltage Test Set
-
It is extensively used in electrical and power generation industry for varied testing operations.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-123-HI
Programmable Resistor Module
The 40-230-123-HI (PXI) and 42-230-123-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Insulation Testers
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
Product
Digital Panel Meter
-
Nippen Electrical Instruments Co.
To be supplied with the right meter, simply furnish the following details in your order: Model Number, Description of the Meter. Accuracy Class. Voltage Input (110 Volts from PT, 240 Volts line to neutral or 415 Volts Line to Line). PT Ratio specifies the High Voltage Primary first ( 33 kV.110V). Current input (5Amps or 1 Amp secondary ) CT ratio (e.g. 100/5 Amps. etc.). Aux. Supply : 50/60 Hz (240VAC of 110/VAC). Dimension : 96 x 96mm or 48 x 96 mm or 144 x 144 mm.
-
Product
Withstand Voltage Tester
2672AM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-035-HI
Programmable Resistor Module
The 40-230-035-HI (PXI) and 42-230-035-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 201kΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Detection Electronics
-
Our detection electronics portfolio comprises all the detection electronics elements required for the operation and automation of a high quality light measurement system, including photo-detector signal recovery and digitisation (with fully programmable DC, AC and lock-in amplifiers having current/ voltage inputs), high voltage supply, optical chopper control, detector thermoelectric cooler control and relay unit.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-714-HI
Multiplexer Module
The 65-231-714-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the multiplexer.
-
Product
High Voltage Instrumentation
-
For applications requiring high voltage isolation, Encore Electronics offers a line of DIN rail mounted instruments.
-
Product
Automation
-
The Transformers and measurement capacitors used in high voltage and Partial Discharge test equipment are typically reliable over several decades of continious use. The control technology is however typically obsolete after only 10-15years. MPS offers automated , state-of-the-art High Voltage Testing Equipment with the following features.
