Remote Terminal Unit
Collects data from data acquisition (DAQ) devices and transmits the information to the main test system via a network.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Connection Units
-
Leuze electronic GmbH + Co. KG
All peripheral devices – such as sensors, safety switches and cameras – require a connection to the fieldbus or a control unit. Depending on device type and area of application, our modular connection units offer variable interfaces that enable simple connection of the devices directly to the fieldbus and thus ensure simple integration of new devices in the system.
-
Product
Remote Intelligent Pod
ScanTAP
-
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 26.5GHz, 50Ω, SMA, Remote Mount
40-784B-131-E
Multiplexer Module
The 40-784B-131-E (PXI) and 42-784B-131-E (PXIe) are single SP4T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
8-Slot USB 3.0 IDAQ Base Unit
iDAQ-938
-
USB 3.0 SuperSpeedWide range power inputLED status indicatorsPhysical ID switch for multiple module identification8 iDAQ slots2 programmable function pin for timing signal (trigger, clock) input/output
-
Product
LXI Microwave Multiplexer, SP4T, 12-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-512
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals up to 40GHz with automatic termination of unused signals
-
Product
Value-added Module With 4 Terminal Block 4-wire Isolated RS-232/422/485
VAM100
-
*4 4-wire Isolated RS-232/422/485*Swappable modular design*Maximize I/O flexibility*2kV isolated protection*Designed for tBOX300/500 series*LVD, FCC, EN 50155 and IEC 60945 certified; CE compliant
-
Product
8Ch Speaker/Receiver Unit Tester
BK9012
-
Based on the BK2120A Audio Analyzer, the BK9012 is designed to quickly test microspeakers or receivers 4~8 at a time at a rate that you’ll find hard to keep up with. It tests various frequency characteristics and also rub & buzz so you know the quality of your product is maintained. And of course, you can track the accuracy and stability of your process using the data you’ve saved on about 4 million microspeakers (based on a 6 second total test + load time) per month.
-
Product
PCIe to PXIe Remote Control Interface Cable, 5m
43-921-500
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
Proving Units for High Voltage Testing Equipment
-
A high quality range of proving units provide the important role of verifying the safe operation of high voltage potential indicators used by power engineers, maintenance personnel and service engineers. The proving units are essential tools for testing HV equipment before and after use.
-
Product
GPIB-RS232, Instrument Control Device - United Kingdom 240VAC
779732-06
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Keysight Dual 1x2 SPDT Terminated Microwave Switch Module for 34980A
34946A
Microwave Switch Module
The Keysight 34946A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as two independent 1x2 (SPDT) terminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
Product
Mis-Matched Termination
-
RF Lambda’s mis-matched terminations are used to present a specific non ideal VSWR to RF components. Both variable and fixed models are available in a variety of power handing capabilities.
-
Product
Servopulser Control Unit
4830 Controller
-
The 4830 has been developed as a controller for servo control type test devices to have the ultimate in advanced performance and operator ease. A single controller unit allows a variety of tests from testing of static properties through to testing of endurance and dynamic characteristics, and has all functions and performance required of a controller for testing machines for actual objects and structures in addition to materials.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, MCX
42-876A-102
Multiplexer Module
The 40-876A-102 (PXI) and 42-876A-102 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
Actuating Units
-
In modern vehicle development and testing technology, reproducible test results are indispensable. Pedal robots are a key component for performing accelerator and brake pedal actuations with the highest precision and repeatability.
-
Product
Remote I/O
-
ADAM remote I/O are categorized into 5 families: IoT/OPC UA Ethernet I/O, Modular I/O system, RS-485 I/O and Serial/USB Converters/Repeaters.
-
Product
8Relay Robust Modbus RS-485 Remote I/O
ADAM-4168
-
8ch relayOperation temperature:-40~85°C,Power input:10VDC~48VDCNoise protection: 4kV surge(power),4kV EFT,8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
34-Pin IDC Breakout, DIN Rail Mount, Screw Terminal
40-967-534-M
-
This accessory is designed to be used for terminating a 34-Pin (0.050" pitch) Ribbon Cable Connector and includes a strain relief. The accessory is suitable for mounting on DIN rails.
-
Product
Digital Relay and Merging Unit Tester
POM2-3333
-
POM2-3333 Digital Relay and Merging Unit Tester is equipped with 6*12.5A and 6*120V outputs, 8 pairs of BI, 4 pairs of BO and 6 fiber optic ports, built-in GPS, supporting PPS, IRIG-B, PTP/IEEE1588 time synchronization.
-
Product
8Relay Modbus RS-485 Remote I/O
ADAM-4068
-
8ch relayProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-004
Multiplexer Module
This multiplexer has low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
Remote High Performance Receiver
E1709A
Receiver
The measurement signal frequency changes as the stage velocity changes. The Keysight E1709A ensures minimal phase processing errors due to frequency changes. The receiver also provides immunity to errors induced by changes in measurement signal power that occur due to small pitch, roll and yaw movements during stage motion. These features help provide the most accurate measurements under system motion.
-
Product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX Terminated
40-876-102
Multiplexer Module
The 40-876-102 is a 50 Ohm 4 to 1 RF multiplexer with 2 banks in a single PXI slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-876 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI 4x4 10GHz Matrix with Termination
40-787-518-4X4-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-507
Multiplexer Module
Our 60-803-507 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
8Power Relay Modbus RS-485 Remote I/O
ADAM-4069
-
8ch power relayProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
Automotive Production Test Unit
GTU
-
The GTU vehicle bumper electronics tester helps engineers to ensure that the correct components are present, of the correct engineering revision and that they function as designed.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
42-785C-421-T
Multiplexer Module
The 40-785C-421-T (PXI) and 42-785C-421-T (PXIe) are single failsafe SP4T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-785C-523-TE
Multiplexer Module
The 40-785C-523-TE (PXI) and 42-785C-523-TE (PXIe) are triple failsafe SP6T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
