Rectifier Testers
-
-
Product
CTE Tester
CTE-360
-
The CTE-360 measures thermal expansion coefficients on wide range of materials over a temperature range of -20°C to 100°C. Although intended primarily for the study of materials used in electronic packaging applications, it can be used on virtually any solid, gel, paste, or viscous liquid over this temperature range.
-
Product
Earth Ground Tester
-
Weshine Electric Manufacturing Co., Ltd
UT520 series can perform precise 3-wire and simple 2-wire earth resistance measurement for power and electrical systems, lightning protection equipment, and ground system of all electrical equipment.
-
Product
Temperature & Humidity Testers
-
Amprobe wireless temperature and humidity testers combine precise, accurate measurement of temperature and humidity with wireless communications up to 80 feet/25 meters to save time and steps. Measure and monitor temperature and relative humidity measurements over time using an Amprobe temperature and humidity data logger. These meters enable you to download measurements to your PC via an USB interface.
-
Product
Automated Filter Tester
3160
-
Automated Filter Tester 3160 is the most advanced automated tester available for challenging filters and filter media with submicrometeraerosols. It can be used to test both low- and high-efficiency filters and filter media, up to 99.999999% efficient (eight 9’s),or penetrations down to 0.000001%. The 3160 uses a bank of atomizers and the TSI Electrostatic Classifier to challenge a filter or filter media with known-size, monodisperse particles.
-
Product
Hipot Tester
19070
-
Chroma 19070 series are the smallest Hipot Testers currently available in the world. Its super mini size is easy to carry and the large LCD display is suitable for viewing measurement results. These sophisticated hipot testers are most applicable to safety test for electronic components.
-
Product
AMIDA 3KS Tester
-
The AMIDA-3KS test system provides a lower cost, cost-optimized test solution for all consumer power management ICs and portable product components. The AMIDA-3KS tester provides 6 board slots in the test head for the required number of analog board channels, thus reducing the overall system procurement cost, making the cost-effectiveness of each board channel 2 times higher and more flexible. The customer's product testing time is greatly shortened.
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
Product
Oxygen Permeability Tester
T-OPT Series
-
Oxygen Permeability Tester - QT-OPT series is ideal for industrial application laboratory testing of material for Oxygen permeability testing for quality control, research and development.
-
Product
Compression Testers
-
Dedicated compression testers offer low footprint test systems. Lever operated systems allows for quick and repeatable compression testing. The wheel operated system allows for more precision with hand wheel operation. The motorized compression tester allows for the most control and the highest degree of repeatability with the ability to set a constant test speed.
-
Product
Static Tester
DRK151
-
Shandong Drick Instruments Co., Ltd.
The tester is applicable in testing the surface potential and the properties of anti-static products .This tester applies to test electrostatic voltage of charged object such as conductor, insulator, and the human body.
-
Product
Tensile Tester
-
Wewon Environmental Chambers Co, Ltd.
Is a fundamental materials science test in which a sample is subjected to a controlled tension until failure
-
Product
RF Signal Testers
-
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
Product
Motor Stator Tester
DZ900
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of y-type three-phase motors.
-
Product
DMX Tester
DMXter 2U
-
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
Product
Multifunction Installation Tester
COMBI519
-
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
-
Product
CMP Tester
CP-6
-
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
Product
Fiber Testers
-
Shenzhen Noyafa Electronic CO.,LTD
Provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
Cable Transmission Tester
SIGNALTEK CT
-
If you install or maintain data cabling, SignalTEK CT allows you to generate PDF test reports that prove installed links run at Gigabit Ethernet transmission rates.
-
Product
In-Circuit Tester
Eagle MTS180
-
The Eagle offers low testing cost for high volume with even the most complex fixture applications. Equipped with a Press-Down-Unit and a combination of analog and hybrid In-Circuit test pins, the MTS180 is in a class for its own. Furthermore, the tester can be equipped with functional test modules to provide even higher fault coverage and thus satisfy the test requirements of a larger number of customers.
-
Product
Electrical Testers
-
UEi Test & Measurement Instruments
Devices designed to test the presence of, rather than measure, electrical conditions.
-
Product
Fabric Drape Tester
TF118
-
TESTEX Testing Equipment Systems Ltd.
Fabric Drape Tester, to measure and calculate the coefficient of drape by tracing a shadow of the draped fabric on paper. Fabric Drape Tester complies with BS EN 9073, BS 5058, ERT 90-1, etc.
-
Product
Antenna Position Tester
FTA
-
Fuzhou Fuguang Electronics Co., Ltd.
FTA series Antenna Position Tester is a convenient test instrument for planning, construction, maintenance and optimization of antenna system.
-
Product
DIGITAL EARTH TESTER
MTD-20KWe
-
The MTD-20KWe digital earth tester allows for the measurement of Earth Resistances and Soil Specific Resistivity, and also the spurious voltages caused by parasitic voltages present in the soil.
-
Product
Wrinkle Recovery Tester
TF112 AATCC
-
TESTEX Testing Equipment Systems Ltd.
AATCC Wrinkle Recovery Tester is used for determining a fabric's ability to recoverafter wrinkling under a pre-determined load for a set period of time.Provided with a set of 5x3 dimensional plastic replicas to grade fabrics 1-5.
-
Product
P-GW Functional Tester
-
The LTE PGW Functional Tester provides a wrap-around test solution for the Packet Date Network Gateway by emulating all the LTE network elements surrounding the PDN-GW (System Under Test). The P-GW Functional Tester emulates LTE Core Network entities such as the S-GW, PCRF, OCS and OFCS. It tests the S5/S8, S7/Gx, Gy and Gz interfaces of the P-GW.
-
Product
Ground Bond Tester
260 Series
-
Our 260 Series makes Ground Bond testing simple. We offer two models so that you can have a simple and easy-to-use Ground Bond tester that provides the output current you need to satisfy NRTL specifications. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 260 Series can easily be deployed in both laboratory and production line environments.
-
Product
Analogue IC Tester
SYSTEM 8 (AICT)
-
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
Product
Distribution Transformer Tester
ADOC-3
-
The ADOC-3 is an equipment that has been designed to test distribution network transformers from 5 kVA to 3MVA.
