Beam Sensors
See Also: Beam
-
product
Digital Meteorological Sensor
ZET 7023
The ZET 7023 weather sensor is a measuring unit with two in-built sensors one of which is responsible for measuring relative humidity and temperature, and the other one, for atmospheric pressure measuring.
-
product
Luminescence Sensors
Luminescence sensors detect visible and non-visible marks that illuminate when using ultraviolet (UV) light. Fluorescent material and marks are reliably detected independently of their pattern, colors or surface conditions on any material. Luminescence sensors emit UV light with a wave length of approximately 375 nm. Fluorescent substances convert the UV light into long-wave visible light, which is then received and evaluated by the luminescence sensor.
-
product
Lambda Oxygen Sensor
KS60002
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
UV Light Sensor
28091
The UV Light Sensor measures ambient ultraviolet intensity in the 200 to 370 nanometer range, within the solar ultraviolet UVA, UVB, and UVC light spectrum. The sensor has a built-in amplifier with adjustable levels. The UV Light Sensor may be used outdoors in a variety of applications including datalogging and closed-loop control, such as for activating watering or greenhouse vents.
-
product
Event Based Image Sensors
EVS
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
product
GS1 Acceleration Sensor
AGS11151
Panasonic Industrial Devices Sales Company of America
GS1 Acceleration Sensor
-
product
Automotive Sensors
Sensors enable the ability to measure parameters such as pressure, temperature, and humidity to make cars more efficient, increase performance, and safer.
-
product
Average Power Sensors
E9300
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (80 dB maximum)Accurate average power measurements on all modulation formats Wide frequency coverage from 9 kHz to 18 GHz (special option to 24 GHz)Calibration factors stored in EEPROM Fast measurement speed over the GPIB (up to 400 readings per second with the E4416A)
-
product
Thermal Infrared Sensors
Excelitas “Thermal IR Sensors” represent a wide range of Pyroelectric Detectors, Thermopile Detectors and IR sensor modules. Our leading edge IR sensing technologies are used for motion detection, presence monitoring, temperature measurement and gas detection to enable smarter homes, improved energy efficiency, better health, safer home security and a more expansive and connected IOT. In addition to our wide offering of off-the-shelf devices, we also specialize in customized solutions for your specific needs.
-
product
In-Line IR Sensor
ILA
10:1 Distance to Target Ratio, 32 to 932F. Dwyer Series ILA Non-Contact Sensors, measure temperatures from 32 to 932F (0 to 500C) and provide a linear 4 to 20 mA, 0 to 5 VDC or thermocouple output. The 2-wire signal is compatible with almost any indicator, controller, recorder, data logger, etc., without the need for special interfacing or signal conditioning.
-
product
Door Contact Sensor
ENVIROMUX-M-DCS
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
product
33% Beam Splitter - BK7, fixed horizontal-bend mount
E1834E
The E1834E is a 33% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
-
product
Split Type AC Current Sensor
CTF-16
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Wide measuring range (AC 0.1～100A).*Compliant with RoHS drective.
-
product
Position Sensors
Panasonic Industrial Devices Sales Company of America
Analog input devices are designed for highest requirements like within the automotive market. In SMD or THT technology, with detents or without detents, the electrical as well as the mechanical performance is impressive. Key features like “long-life endurance” or “accuracy in output-signal” give customer applications highest performance. Possibilities of Haptic-alignment make these components perfect.
-
product
Consumer Global Shutter Image Sensors
Smart GS Series
SmartSens creatively combines the backside-illuminated (BSI) pixel design process with the Global Shutter image sensor design to provide imaging performance with better signal-to-noise ratio, higher sensitivity and wider dynamic range . The new vitality of intelligent sensing equipment.
-
product
Sensors And MEMS Test
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff
-
product
Sensors
A device that produces an output signal for the purpose of sensing a physical phenomenon.
-
product
SparkFun Air Quality Sensor
SGP30 (Qwiic)
The SparkFun SGP30 Air Quality Sensor provides information on the quality of the air in your room or house by monitoring the volatile organic compounds around the sensor. The SGP30 Air Quality Sensor can return valid indoor air quality (IAQ) readings within 15 seconds of powering up! By comparison, typical air quality (IAQ) sensors are great for measuring CO2 and volatile organic compounds (VOCs) but some of them require a burn-in time of 48 hours and a 20-min start up time.
-
product
Hall Sensor Board with I2C Interface
056-742
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
SparkFun Atmospheric Sensor Breakout
BME280 (Qwiic)
The SparkFun BME280 Atmospheric Sensor Breakout is an easy way to measure barometric pressure, humidity, and temperature readings, all without taking up too much space. Basically, you can find out anything you need to know about atmospheric conditions from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Cavitation Sensors
Cavitation is often induced by an external acoustic field which typically has very high acoustic amplitudes but the acoustic emissions from these cavitation events are significantly smaller. The small acoustic emissions are characterised by well defined spectral peaks at integer harmonics and sub-harmonics relative to the fundamental bubble frequency.
-
product
Temperature Logger with Integral sensor and Probe
TV-4510
Dual channel temperature recorder LCD display of current readings 30,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor and battery low indicator Programmable alarms Optional audible alarm box USB and serial download cables
-
product
Beam Directional Power Supply Mains
SiteX CP200D
Being just 20 mm longer than the CP160D, the CP200D represents the best compromise between high penetration (up to 42 mm for steel) and the capacity of the generator to fit with various NDT applications, such as inspections of more technical materials in the aeronautical or space industries. The CP200D is one of the most versatile generators on the market and thanks to its built-in multiple X-Ray output carrousel it will adapt to a very wide variety of NDT applications, without compromising in any manner its light weight (12 kg) and ease of use.
-
product
Digital Strain Gauge Sensor
ZET 7110
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
product
Pressure Sensors
At the heart of every Tekscan pressure measurement system is an ultra-thin, tactile pressure sensor. Every Tekscan sensor is comprised of numerous individual sensing elements, or sensels. The sensel density represents the total number of sensels per unit of area. In order to use Tekscan's pressure sensors, you must have a Tekscan pressure measurement system as well as the corresponding sensor map (software driver) for the sensor.
-
product
Soil Moisture Sensor
SoilWatch10
SoilWatch 10 is a soil moisture sensor which allows measuring relative water content in the soil. Our sensor does not have any exposed electrodes that usually corrode in resistive sensors. Whats more the reads will almost not drift over time or with temperature changes. Our sensor will give the same readings regardless of supply voltage. The sensor is weatherproof. It can be buried in soil for extended periods of time without adverse effects on accuracy or reliability. Designed to work with Arduino.
-
-
product
Open Loop Current Sensor
C03 50A
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in systems for industry and commerce as well as in communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
product
Sensors
ACM-PLUS Family of High-Accuracy Current, Wave, & Tide Measurement Instruments and Systems
-
