Solenoid Testers
-
Product
Twist Tester
TY370
-
TESTEX Testing Equipment Systems Ltd.
Yarn Twist Tester, to determine yarn twist in single or plied yarns, quadrant type with auto stop & reverse for conventional or untwist/re-twist methods. Twist tester offers adjustable test length up to 500mm/20 inches for S & Z twist yarns.
-
Product
406MHz BEACON Tester
-
The 406MHz BEACON TESTER is specified service equipment and reliable test solution for ship surveyors, beacon suppliers, classification societies and administrative authorities. It assures operation checking of all types of distress beacons (EPIRB, PLB) of any manufacturer, and any other device (SSAS, SVDR, VDR) operating within COSPAS-SARSAT system.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc., By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit., Provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
Product
Socket Tester
ST120+
-
The Fluke ST120+ GFCI Socket Tester with Beeper checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120+ will give you confidence on your next job.
-
Product
Multicore Universal Solderability Tester
MUST System 3
-
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
Product
Base Number Tester
LD-LAAT-A13
-
LabodamLD-LAAT-A13is composed of automatic potential titrator and titration device. It is designed according to Industry Standard of Petrochemical and follows ASTM D2896 and ASTM D4739 Test Methods for Base Number of Petroleum Products.
-
Product
Partial Discharge Tester
GTPD-2C
-
GTPD-2C Digital partial discharge tester is the digital partial discharge measuring and analyzer adopting the complete new generation technology. It is suitable for partial discharge detection in manufacturing factory and field handover test of transformers, generators, CT/PT, bushings, GIS, capacitors, power cables, switches and other high-voltage electrical equipment with various voltage levels and capacities.
-
Product
Circular Locus Tester
TF225
-
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Using an active friction system, fabric is rubbed against a nylon brush and abrasive or an abrasive only under controlled conditions. Results of the test are achieved in minutes. The relative motion of the locus specimen grip and the abrasive platform is a circle with a relative speed of 60+/-1 r/min. The grip offers pressure to the specimen which is adjustable with a tolerance of +/-1%. For added control and safety, the machine is equipped with a self-stop switch.
-
Product
Water Vapor Permeability Tester
WPT-304
-
WPT-304 Water Vapor Permeability Tester is manufactured based on the gravimetric method and is applicable to test the water vapor transmission rate of plastic films, composite films, sheets, and other materials used in packaging, medical and constructive industry.
-
Product
Power Cord Bending Tester
SW-6
-
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
Product
Vapor Pressure Tester
-
The MINIVAP laboratory and process vapor pressure analyzers are the worldwide accepted standard instruments for the determination of the vapor pressure of gasoline, crude oil and LPG.
-
Product
Validation Testers
M Series
-
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
-
Product
Bump Tester
KD-163
-
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
Product
AC High Voltage Tester
VHT
-
VEER make High Voltage Tester VHT is specially designed to test Dielectric Strength of Device under Test as per applicable standards. High Voltage test is required to determine whether test object has proper insulation or not. High Voltage test is carried out as Routine Test Each device is subjected to test at high voltage of 1 kV + 2 x (working Voltage)If Insulation is weak then device will consume more power because of leakage current which causes more heat. Heat will reduce the reliability and overall life of device under test It is also responsible for high risk of electric shock. So, High voltage test is necessary for all electrical equipments.
-
Product
Flying Probe Testers
-
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
Product
600V Battery Discharge Tester
-
Foresight Electronics Co., Ltd.
Battery Volt. Ranges 300V-600VMax. Power 18KWAccuracy & resolution ≤±0.5%, 0.01VDC Voltage measurementInternal current range 2-30A
-
Product
E84 Handheld Tester
E84
-
The E84 Handheld Tester is the most efficient tool available for quickly testing, trouble-shooting, and resolving E84 problems. This self-contained, battery operated tool integrates the industry-leading automated load and unload routines provided in the E84 Emulator.
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
External Flashlight Gem Tester
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
Gem Tester Refractive index is one of most important optical parameter. Gloss of gem can be estimated by the parameter.The kinds of gem can be precisely determined in accordance with the measured value of refractive index because every kind of gem has its inherent refractive. Besides, index of double refraction can be also measured. Through the parameter you can judge whether a gem is uniaxial or biaxial photopositive or photonegative.
-
Product
Infusion Pump Tester
IN-600
-
Measuring and testing device for checking infusion pumps according to IEC 60601-2-24.
-
Product
PAT Testers
-
Complete with a comprehensive range of PAT labels, adaptors, software and our bespoke range of PAT testing kits we can cater for electrical safety testing in domestic, commercial and industrial environments.
-
Product
Flat-plate Thermal Conductivity Tester
-
TESTEX Testing Equipment Systems Ltd.
Flat-plate Thermal Conductivity Tester, to determine the thermal conductivity of various fabrics, quilting products, and other heat insulation materials.
-
-
Product
AC Hipot Tester
298
-
Our Model 298 is a simple-to-use 500VA AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 298 500VA AC Hipot Tester includes all the features you need to get the job done and move on.
-
Product
AC Ground Bond Tester
446
-
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
Product
Film Tearing Strength Tester
DRK108C
-
Shandong Drick Instruments Co., Ltd.
DRK108C Tearing Tester is applicable in the tearing test of films, sheets, flexible PVC, PVDC, waterproof films, woven materials, polypropylene, polyester, paper, cardboard, textile and non-woven, etc.
-
Product
GFCI & Receptacle Tester
-
GFCI & Receptacle Tester - GFCI & Receptacle Tester for electrical work.
-
Product
Bit Error Rate Testers
-
The Tektronix BERTScope® and PatternPro® families provide a range of signal conditioning and BER test solutions from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry’s broadest serial communications test portfolio of Bit Error Rate Tester products.
-
Product
Pendulum Impact Testers
MPX
-
Delivering precision and safety in high-volume materials testing, the MPX pendulum impact system from Instron is optimized for Charpy and Izod testing of metals. Equipped with Bluehill Impact software, it supports capacities from 300 J to 900 J and features motorized hammer lift, automatic return, and interchangeable hammer weights. An enclosed, interlocked safety guard ensures operator protection in compliance with CE and ISO 13849 standards. The system supports key standards including ASTM E23, ISO 148, EN 10045, and others, while offering configurable reports and seamless data export capabilities.
-
Product
Non-Contact Resistance Online Tester
-
Non-Contact Resistance Online Tester is our company devotes ourselves to Grounding resistance test technical research’s another new high-tech product for more than ten years. Detector adopts weather fastness material manufacture, temperature resistance, cold-resistant, corrosion prevention, fire prevention. Detector’s structure is rigorous and firm, against rain, dustproof, installation and use outdoors. Non-contact measurement, safe and reliable, Ease of installation. Grounding down lead is directly through the detector perforation, Will not affect lightning protection grounding effect and the normal operation of the facilities. Ensure high-accuracy, high stability and high reliability of long time on-line monitoring outdoors, underground mine and indoors.
