Voltage Regulators
-
Product
Temperature and Humidity Regulator
H3331-2
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
12-690V Voltage Tester With LED Display
7337
-
Peaceful Thriving Enterprise Co Ltd
Measurement by LED Display1. Double-pole Test2. High Voltage Indication3. Phase Rotation Test4. Polarity Indication5. Continuity Test6. Illumination
-
Product
AC DC High Voltage Divider
-
NMC make products are the ideal equipment for HV measuring products are the ideal equipment for HV measuring instruments, apply in power system, electronic equipment factory to test frequency AC high voltage and DC high voltage. This product is composed by HV measuring part and LV display instrument. HV part and LV display instrument are separate when working, it is safe and reliable.
-
Product
Compliance Voltage Ohmmeter
ΩhmRanger-LCV
-
ΩhmRanger-LCV is an accurate, 3.5 Digit, Low Compliance Voltage Ohmmeter. It is able to measure from >100M to 10 Ohms, ΩhmRanger-LCV is suitable for professionals and enthusiasts alike.
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
DC REGULATED POWER SUPPLIES
IBL-RPS-3020
-
International Biological Laboratories
One channel output, Two Red LED digital output voltage and current value each, Constant voltage, current stabilizer, the two states can be auto-changeable, Current-limifing protection and limiting-dot adjustable optionally
-
Product
Compressed Air Temperature and Humidity Regulator
H3021P-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Digital High Voltage Meter
-
AllWin Instrument Science and Technology Co., Ltd.
Voltage, is 4 1 / 2 digital displayTrue RMS measurement High accuracy and stableSuitable for all waveform measuremen
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
High Voltage Probe
PL-10
-
*MODEL：PL-10*IMPEDANCE：1.111MΩ*ACCURACY： ±0.25%*FREQUENCY B.W.：DC~50MHz*WORKING POWER：MAX. 1Watt*INPUT VOLTAGE：MAX.250VDC or 200V rms AC*DIMENSION：46mm(L)xΦ16mm(D)*WEIGHT：25g
-
Product
15k Voltage Probe
15KVP
-
Our 15KVP voltage probe allows direct connection up to 15,000 Vrms (15KV) 3 phase power.
-
Product
BJT Voltage Preamplifier
SIM911
-
Stanford Research Systems, Inc.
The SIM910 and SIM911 are low-noise, programmable preamplifiers which are ideal for a wide range of small signal applications. The primary differences between the two models are their input impedance and input noise.
-
Product
Medical Withstand Voltage Tester
2670YM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Medical Withstand Voltage Tester，2670Y Medical Withstand Voltage Tester Has All The Function Of The Conventional Withstand Pressure Tester,And Increasing The Arc(Flashover)Detection Function,It Can Test The "Flashover" Phenomenon Of Electrical Equipment Intuitively,Accurately,Rapidly And Reliably Through The External Oscilloscope,The Measured Electrical Equipment Without "Flashover" Phenomenon,
-
Product
AC/DC Withstand Voltage Tester
2672
-
Shenzhen Chuangxin Instruments Co., Ltd.
AC/DC withstand voltage tester Features: High voltage,small current, high accuracy. Leakage current, testing time, continuous arbitrarily, well-adapted.
-
Product
Voltage Control Attenuator
-
Voltage variable attenuator offering infinite attenuation precision and broadband performance
-
Product
High Voltage Power Supply
PS300
-
Stanford Research Systems, Inc.
The PS300 High Voltage Power Supply series consists of three efficient, microprocessor-controlled, switching DC power supplies capable of delivering 25 W of output power at voltages up to 5 kV.
-
Product
Stand Alone Low Voltage Testers
-
Low voltage testers are a special type of device used to identify opens and shorts in applications that are driven on low voltages.
-
Product
Stand Alone Low Voltage Tester
TestMate 256
-
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
High Voltage Test System
CKT1175-15
-
12.5 mV – 2000 VDCIR measurements to 5000 megohmsHipot testingDwell time prog. from 1 ms to 1000s in 1 ms steps
-
Product
Bench/System DC Power Supply With PowerFlex Or PowerFlex+ Regulation
QPX Series
-
Wide range of voltage/current combinationsUp to 80V and up to 50A within the same power envelopeLow output ripple and noise of <3mV rms at full powerHigh setting resolution of 1mVAnalogue control interfaces for voltage and currentBench or rack mounting, front and rear terminalsUSB and LAN (LXI) interfaces with GPIB optional (QPX600DP, QPX1200SP and QPX750SP)
-
Product
Voltage and Current Measuring Technology
-
HIGHVOLT Prüftechnik Dresden GmbH
Designed for the measurement of alternating current (AC), direct current (DC), lightning (LI) and switching (SI) impulse high voltages (HV) as well as AC and impulse high current (HC) according to IEC 60060, IEC 61083 and IEC 60052, available as indoor and outdoor design.
-
Product
Digital Automatic Pressure Regulator
UR-Z700 Series
-
The high performance auto pressure regulator UR-Z700 Series has electronic regulators with high-precision pressure sensors and high resolution, fast response piezo actuator valves. They control the pressure relative to the external control signal that they receive. For both Digital/Analog and DeviceNet™ communications.
-
Product
AC Voltage and Frequency Transducers
NMTU/F
-
The NMTU/F device is an AC voltage and frequency transducer with two independent analogous outputs. The A output measures AC voltage, the B output measures the frequency of input voltage. That´s why one single NMTU/F transducer is able to replace two customary transducers, thus making it possible to achieve significant savings in installation space.
-
Product
High Voltage Surge Testers
10000HVST
-
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
Product
RF Voltage Probe
P-20 Series
-
The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.
-
Product
Flexible Range Regulated DC Power Supply
PSF-L Series
-
* Flexible output range Possible to output voltage and current flexibly within the rating power. In case of PSF-800L, 10V/80A to 80V/10A, 20V/40A to 40V/20A, etc. are available corresponding to plural number of conventional regulated DC power supplies.* 90rotating panel operation part 90rotating panel installs the unit vertically or horizontally.* Sequence f
-
Product
100-250V AC/DC Voltage Tester
7321
-
Peaceful Thriving Enterprise Co Ltd
Voltage Tester is designed to make reliable, safe and easy testing of voltage, with standard handhold to make it easy to use. There are visibility neon to offer clear indication and adding test lead holders spaced to fit the outlet. These features combined with a durable ABS housing and with UL and cUL approvals make the choice of professionals.
-
Product
C Series Voltage Input Module
-
The C Series Voltage Input Module helps you work with voltage measurement applications. This module features isolation to separate channels from each other, from COM, or from earth ground for safety, noise immunity, and high common-mode voltage range. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. You can use included options such as configurable input ranges, output channels, various connectors, and enclosed or non-enclosed modules.The C Series Voltage Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
High Voltage Isolator for Logic Analyzers
LX-08
-
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
