CAT III
-
product
CAT III Digital Multimeter
82600
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
product
Handheld Oscilloscopes, 100 MHz, 2 Analog Channels
U1610A
100 MHz2 analog channelsTroubleshoot in any weather with channel-to-channel isolation and a CAT III 600 V safety ratingIdentify glitches easily with dual window zoomView subtle signal details more clearly with up to 1 Gsa/s sampling rate and 120 Kpts memoryDebug under any lighting conditions with 3 selectable viewing modes (indoor, outdoor and night vision)Get 3 instruments in 1: a dual-channel oscilloscope, built-in DMM and data loggerEasier start-up with 10 selectable languages
-
product
Differenzial Probe
BumbleBee®
PMK Mess- und Kommunikationstechnik GmbH
BumbleBee® is a 400 MHz, 1 kV CAT III high-voltage, differential probe, that can be used with anyoscilloscope or device providing 50 Ω termination.
-
product
AC/DC Analogue Voltmeter
ED-9200
Standard Electric Works Co., Ltd
Precision instrument for plant maintenance, field servicing and educational purposes Principle: Moving coil type Accuracy: 0.5% F.S. Safety Standards: EN 61010-1 CAT III 1000V EN 61326-1 Scale Length: Approx. 135mm 5-3/8"
-
product
Digital Insulation Mult-Meter
8010 IN
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 125V, 250V, 500V, 1000V● The maximum insulation measurement range is 200G ohm @1000V.● 1mA test current on insulation test at nominal voltage.● With a hand strap for easier holding.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III 600V IEC 61557-1 IEC 61557-2 EN 61326-1
-
product
5A Microohm Meter
9005 UO
Standard Electric Works Co., Ltd
● Maximum testing current of 5A ● Ranges: 2000μΩ / 20.00mΩ 5A 20.00mΩ / 200.0mΩ 1A 2.000Ω / 20.00Ω 100mA 200.0Ω 10mA● Maximum resolution of 1μΩ at 5A● Four terminal measurement● 4 Lines × 20 Characters LCD ● Memery function (200 measurement results)● Auto power off● Low battery indication● Power source: 1.5V "C" alkaline battery × 8● Safety Standard: EN 61010-1 CAT III 300V EN 61326-1
-
product
Intelligent Digital Multimeter, Calibrated, 3999 Count, Mean Value, Auto, Manual Range, 3.75 Digit
72-7755 CAL
The 72-7755 CAL from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
product
Midi LoggerHV
GL2000
*4ch High Speed Simultaneous Sampling*CAT III 600V Compatible*Measure AC 600V Measurement with Trur-rms.*Built-in high-capacity RSAM (4 M sampaling/ch) and Flsasg Memory (4 GB)*Large Easy-to-read 7-inch LCD
-
product
400 MHz High Voltage Differential Probe
DP0001A
The DP0001A is a 400 MHz high voltage differential probe with 2 kV mains isolated or 1 kV CAT III rating designed for making accurate high-voltage power measurements required for testing today’s WBG power devices, power converters or motor drives.
-
product
Clamp Meters
Clamp meter is a rugged high end AC clamp meter. With a UL listed safety rating of CAT IV 600V / CAT III 1000V, this clamp meter is built to get the tough jobs done.
-
product
Digital Multimeter and Phase Rotation Tester
3000 MPR
Standard Electric Works Co., Ltd
● 4000-count LCD● Auto ranging● Voltage, Resistance, Current, Continuity, Diode measurement● Can measure Resistance up to 200.0 Mohm● Checks a wide range of 3-phase power sources (80~750VAC)● Phase Rotation indication : clockwise and counter-clockwise on LCD● The LCD will show AC voltage between phases and Phase Rotation● Wide range for capacitance test: 0~40000μF(40.00mF)● REL / Auto-Zero function● MAX /MIN function● VAHz function● Frequency : 40.00 MHz● Data hold function● Over range indication● Low battery detection● Auto power off in 15 minutes● Convenient stand for viewing● Comply with EN 61010-1, CAT III 600V for the range of 600V AC/DC
-
product
Phase Sequence Indicators (Contact Type)
887 PR
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● No battery required.● Phase rotation phase presence indicated on large liquid crystal display.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 40Vac to as high as 600Vac.● Fused.● Lightweight, robust and compact.● EN 61010-1 CAT III 600V EN 61010-2-032
-
product
Phase Sequence Indicator
PHS 863
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
product
Test Probe Leads, With 19-mm Tips And 4-mm Tips
U1169A
The U1169A consists of one pair (red and black) of insulated test leads, one pair of test probes with 19-mm tips and another pair of test probes with 4-mm tips. Recommended for use with Keysight handheld digital multimeters. Rated at CAT III 1000V, CAT IV 600V, 15A.
-
product
TRMS AC/DC Clamp-on Power
HT9023
HT9023 has been designed to measure AC, DC AC+DC current up to 1000A in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp also measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.
-
product
Battery Tester
CS-3001
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
product
Voltage/Continuity Testers
VOT-53
Standard Electric Works Co., Ltd
● 2000-count digital display (LCD type). ● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test ● Audible continuity test.● Auto sensing function for: voltage (AC/DC), Ω, diode.● Measurement function: ACV/DCV: 1000V Resistance: 2000Ω Frequency: 30Hz~1kHz ● Phase rotation test : ● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● Flashlight function.● Safety standard : EN 61010-1 CAT III 1000V EN 61010-1 CAT IV 600V EN 61243-3 EN 61326-1
-
product
DIGITAL MULTIMETER, TRUE RMS, 10A, 1KV
72-13570
*True RMS digital multimeter with 40000 counts display*CAT III 1000V, CAT IV 600V safety rating*Manual function select and auto ranging*Measure AC & DC at the same time (AC+DC)*Up to 9999 readings data storage and 0.1% to 99.9% duty cycle*Data hold, max/min/relative modes, analogue bar graph*Full icon display, double backlight*USB interface and Bluetooth connection*Powered by 9V (6F22) battery*12-month limited warranty *view Terms & Conditions for details
-
product
RMS Digital Multimeter
400002
The Sper Scientific 400002 and 400002BT multimeters are True RMS compact digital multimeters with double molded plastic housing and oversized high contrast 4000 counts LCD display. They are CAT III rated for 600V. The 400002BT model includes Bluetooth capability to view and save data on your iOS or Android smartphone, using the free Meterbox Pro Software.
-
product
Multimeters
Bluetooth interface for downloading, viewing, and sharing on Southwire’s MApp™ mobile appOnboard memory allows datalogging even when Bluetooth wireless is not connectedHi-Res color display with graphing featureOn board memory for saving and viewing measurements and recordingsIntuitive menuRugged meter with CAT IV 600V / CAT III 1000V
-
product
Digital LOOP/PSC Tester
8025 LP
Standard Electric Works Co., Ltd
● Battery is not used.● 3 ½ digit LCD (2000-count).● Backlight function.● 15mA loop measurement which will not trip ELCBs.● Convenient and easier for users to measure the loop impedance directly without bypassing the wires.● Wiring check function.● Over temperature protection.● Over voltage protection.● Built-in voltmeter.● Built-in earth tester.● Built-in loop/psc tester.● Safety standard : EN 61010-1 CAT III 300V EN 61326-1
-
product
Differential Probe
DP-8V
*MAX. Input Voltage: ±4KV DC or 8KV p-p or AC 2.8KV rms*Bandwidth: DC-50MHz*Input Impedance 20MΩ// 2PF*x10, x100, x1000 Attenuator*To Ground MAX. Voltage: 4KV CAT III*Output Impedance 50Ω
-
product
Test Lead Set
131139
IEC 1010 Rating: 1000 Volts Cat III Double/Reinforced Insulation 20Amps. Kit Comprises:- 1 Pair 123856/OF-OR/1.2 Double Insulated Silicone Lead Assemblies. 1 Pair 121017 Test Prods. 1 Pair 121026 Sprung Hooks. 1 Pair 126024 Fully Insulated Crocodile Clips. Packed In Silver Wallet.
-
product
Electrical Testers
Precision Mastech Enterprises Co.
AC Voltage range: 50V-1000V AC, 50/60HzSafety standards: Designed to international safety standard IEC61010 - 1/600V CAT III, 1000V CAT II.Battery: 2*1.5V (AAA type)Altitude: <2000mOperating temperature: -10 to 50CStorage temperature: -20 to 60CHumidity: <85% relative humidityDimensions: 157*24*20 mmWeight: Approximately 42g
-
product
Analogue+Digital Multimeter
ST-3502
Standard Electric Works Co., Ltd
● 3½ digit, high contrast LCD, with a maximum display of 1999● Automatic polarity indication, zero adjustment● Low battery (BAT) indication● Over range indication: highest digit of (1) or (-1)● EN 61010-1 CAT III 600V, EN 61326-1
-
product
Fused Test Probes with Silicone Test Leads
AL-57FL
Standard Electric Works Co., Ltd
● AL-57FL is an ideal tool which shows the indication of live voltage even with blown fuse.● 2 replaceable fast-acting fuses are built-in. The specs of the fuses are 1000V, 11A with internal rating of 20kA AC/DC.● Provide additional testing protection.● Help to prevent a possible mis-indication when there is voltage present.● CAT III 1000V, CAT IV 600V, 10A with protective cover.● 2mm probe tips, removable 4mm brass caged banana probe tips are also included.● Include High-quality silicone test leads, 1.5 meter long.● Wipe the fused test probes and silicone test leads periodically with a damp cloth and detergent. Do not use abrasives or solvents.● Operating temperature: -20 °C to +50 °C (-5 °F to 120 °F)● One year warranty● Can't be used on current mode with blown fuse.● Rating : EN 61010-031 CAT Ⅲ 1kV 10A / CAT Ⅳ 600V 10A
-
product
Oscilloscopes
AEMC Instruments proudly introduces the first hand-held portable two- and four-isolated-channel 600V Cat. III Oscilloscopes on the market with 12-bit resolution. Featuring five complimentary tools in one - an Oscilloscope, FFT Analyzer, TRMS Multimeter, Harmonic Analyzer and a Recorder - all in a rugged and ergonomic hand-held instrument. They are the perfect tools for both laboratory and field testing.
-
product
Cable Certifiers
LANTEK III Series
New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.
-
product
Clamp Sensors
Kyoritsu Electrical Instruments Works, Ltd.
Can measure AC current up to 1000A Flexible and light weight by the air core coil used at the sensor part Designed to meet the international safety standard IEC 61010-1 CAT IV 300V, CAT III 600V
