Verifiers
-
Product
RS-232 Cable, 9 Pin (f) To 9 Pin (f)
34398A
-
The Keysight 34398A is an RS-232 cable, 9 pin (f) to 9 pin (f). Standard RS-232 cables are easy to find, but making them work is a different story. The Keysight 34398A has been verified for compatibility with Keysight's bench instruments to take the mystery out of RS-232 pinouts. The Keysight 34398A includes a 9-pin (f) to 9-pin (f) RS-232 cable and a 9-pin (m) to 25-pin (f) adapter.
-
Product
DCA-M Sampling Oscilloscopes
-
Built on Keysight's digital communication analyzer (DCA) technology, the DCA-M family is recognized as the industry standard for verifying optical transmitter compliance to communications standards. With single to quad optical AND electrical channels in a compact form factor, the DCA-M is ideal for both manufacturing and RND applications. Analyze both multi-mode and single-mode signals with the low-noise, high-sensitivity calibrated reference receivers. The variety of models along with the supporting software and compliance applications ensure you can measure with high precision, whether you analyze electrical or optical devices.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
ATEX / FM Approved Grounding Clamps, Cables and Reels
Cen-Stat Static Grounding Clamps
-
Static grounding systems like the Earth-Rite range combine interlock control and visual indication to verified ground connection points and offer the highest levels of protection over electrostatic ignition risks. However, equipment specifiers may select passive grounding devices, like single pole clamps, to ground and bond plant equipment.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Automated Connector Tester
-
GCI's Automated Connector Tester is a self-contained test bench providing reliable testing of filtered and non-filtered electrical connectors. The ACT automates the tedious process of testing each pin against all others and shell for DC and AC leakage. For filter connectors, the ACT accurately measures pin-to-shell capacitance. For pins protected by diodes, the ACT provides leakage and breakdown measurements. The ACT also verifies pins which are intentionally shorted to each other or to the shell.
-
Product
Wire & Cable Testers
-
Precision Mastech Enterprises Co.
Diagnostic tools designed to verify electrical connectivity, map wiring configurations, and detect faults.
-
Product
PNA-L Microwave Network Analyzer
N5239B
-
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to8.5 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Insulation Resistance Tester
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi make device enable us to measure electrical leakage in wire, results are very reliable as we shall be passing electric current through device while we are testing. The equipment basically uses for verifying the electrical insulation level of any device such as motors, cables, generators, windings, etc.
-
Product
Oven Performance Checker
OvenRIDER® NL 2+
-
Regardless of the recipe and what your oven's controls indicate, what your PCB actually experiences at board-level as it goes through the oven can be SIGNIFICANTLY different. Achieve convection reflow oven Verification by separating zonal temperatures from convective heat flow efficiency while verifying conveyor speed for a true picture of oven Lead-Free performance consistency.
-
Product
Electric Vehicle Charger Testing
EV-TEST100
-
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
CT Polarity Tester
DIR CT
-
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
-
Product
Non Functional Testing
-
Non functional testing aims to verify the elements of the solution that are not related to a user action, for example, Failover, and Maintainability. Exactest deliver core non-functional test techniques to include:
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Viscosity Standards
-
Brookfield Viscosity Silicone and Oil Standards provide a convenient, reliable way to verify the calibration of your Brookfield laboratory viscometer/rheometer.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Package Testing
-
Package testing helps manufacturers verify their package designs to ensure that their products will not experience damage during shipping. Products are often shipped across states, countries and continents to reach their destination. This is an unavoidable link in the supply chain and, as such, packaging must be designed to protect products during the shipping process.
-
Product
PNA-L Microwave Network Analyzer
N5234B
-
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to43.5 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Portable Bar Code Verifier
Inspector Model D4000 Auto Optic
-
The Model D4000 Auto Optic provides ISO 15416 and ANSI X3.182 Method. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a laser scanner (either in a single piece or connected with a cable). Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple four-button user interface. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
Product
Phase Angle Meter
597C
-
Red Phase Instruments Australia Pty Ltd.
The Model 470A has similar software and performance as the Model 465C. It is packaged in a 19? style bench-top case with all connections on the front panel for use in meter test benches. It has inputs for comparison with another polyphase standard or 3 separate single phase standards for verifying calibration accuracy.
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
PXI Resistor Module 2-Channel 1.5R to 1.02k with SPDT
40-293-121
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Resistive Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Resistive load banks are an important tool for testing and verifying the performance of power systems such as generators, UPS systems and turbines. They simulate real-world electrical loads by dissipating power as heat through resistive elements.
-
Product
Test Fixtures
-
At Global Test Services LP, we know that verifiable yields are the backbone of your business, which is why we offer innovative, robust solutions that offer you better availability, improve efficiency, and offer flexible, scalable systems that meet the specific quality and test needs of your business.
-
Product
Millohm & LCR
-
Help prevent failures in motor windings, generators and transformers with a quick and easy resistance test using an Amprobe milliohm meter. To efficiently inspect and verify electronic components for quality control, choose an Amprobe LCR tester.
-
Product
Speed-O-Calibrator
16470
-
The Speed-O-Calibrator consists of two sections, control box and drive unit. The control box is stored inside the drive unit for easy portability. The control box weighs less than 6 lbs and is used in the cab of a locomotive to control the speed of the Axle Alternator Drive Unit. The Drive Unit drives the Axle Alternator at various speeds while the user verifies that the correct speed is displayed in the cab. The test system provides a complete test of the speedometer system, including all types and paddle lengths of Axle Alternators.
-
Product
Integrated Solution for Digital Switching & Fiber Optics Operational Verification
VERTA
-
When incorporated into defense/aerospace ATE, Verta enables reliable, error-free bus communication and interoperability tests to verify performance of high-speed, optically networked military weapon assemblies.
-
Product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
