-
Product
FaithTech FTL Series High Precision DC Power Supply (90W-1500W)
FaithTech FTL Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FTL series is a high precision DC linear power supply with high performance, multi-function, medium and small power features. The product is stable and mature, and has comprehensive protection functions such as reverse polarity, overvoltage, overcurrent, overload and overtemperature, which can keep the power supply and load safe in unstable environments. FTL has a regulation rate of < 0.01%, ripple and noise of < 1mVrms and fine transient performance, and is suitable for application environments like current surges. The FTL series DC power supply is not only suitable for high-grade laboratory, but also for high-performance test systems.
-
Product
FC Impedance Meters
-
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
Product
Micro Power Insert, Receiver, SIM, 2 Position, 2 Slot
510180102
-
This insert contains 2 micropower contacts and is part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module. This insert comes loaded with contacts. Individual contacts sold separately p/n 610142106.
-
Product
Third Harmonic Filter
HBF-T
-
Lifasa - International Capacitors, SA
HBF-T filters are designed to block the 3rd harmonic, reducing the neutral currents in three-phase installations where there are installed harmonic generating loads connected between phase and neutral. It is basically passive filters based on a parallel combination of inductance and capacitor.
-
Product
Switch Mode Power Supplies-Air Cooled
-
The MS-Series features constant voltage and current control with easy, quick installation and maintenance. Modular versions easily increase the output by means of series or parallel connection. All models have DC short circuit protection. With forced air-cooled models, the cooling air quantity is controlled in relation to the load reducing contamination and noise levels.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP021-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
Three Phase Load Bank
REOLOAD 310
-
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
-
Product
PXI 10A Power MUX 8-Bank 4-Channel
40-661-001
-
The 40-661 is a single pole PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
6 Slot VPX PCIe Gen2 Chassis
Desert Gecko
-
The 6 slot conduction cooled chassis can dissipate 120W in a non-moving air environment. The fin design and wall thickness was designed and analyzed with Flowmetrics software and designed for minimum delta T offset in an average thermal load application. The design was then verified in real life enviromental chamber experiments with a sealed chassis using our 3U heat simulator modules. Data available upon request.
-
Product
CEAST VisualMELT Software
-
VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.
-
Product
Power Supplies
-
A power supply is a component that supplies power to at least one electric load. Typically, it converts one type of electrical power to another, but it may also convert a a different form of energy - such as solar, mechanical, or chemical - into electrical energy. A power supply provides components with electric power.
-
-
Product
Data Loading Products
-
TechSAT's data loading products are available to support all standard ARINC data loading protocols: ARINC 615/615A/826/844 for ARINC 429 and Ethernet based data loading. For next generation aircraft, TechSAT's data loading solutions bring portability to data loading over the new generation of avionics bus and network types: AFDX®/ARINC 664, Avionic & Deterministic Ethernet, TTP, and ARINC 825/CAN
-
Product
20V/30A/300W DC Programmable Electronic Load
TOB-IT8512
-
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
Turn-Key Short Circuit Laboratories
-
For low and medium voltage switchgear including :*Circuit breakers*Contactors*Disconnect switches*Fuses*Miniature circuit breakersApplied tests for low and medium voltage switchgear :*Dielectric withstand test*Impulse withstand test*Breaking capacity test*Mechanical life testElectrical life test*Over load performance test*Short circuit breaking capacity test**Short time short circuit impulse current test*Temperature rise test*Operation performance testTests for low & medium voltage panels :*Short time short circuit impulse current test*Dielectric test*Impulse withstand voltage test*Temperature rise test
-
Product
Subsea Tensile Link
SUBT-3.0
-
The Subsea Tensile Link is specially designed for working in subsea conditions and is used for measuring tensile loads. With an optional integral 4-20mA amplifier the load cell is packaged in a wooden case with a subsea rated signal cable to customer specific lengths or alternatively can be supplied with a TW-3.0-S display. Fully sealed with a subsea connector and pressure tested to over 250Bar the load cell is the ideal instrument for easily and accurately measuring subsea loads.
-
Product
Thyristor Regulators
-
Small and lightweight thyristor regulators for single-phase loads are characterized with high panel installation density.
-
Product
Combined Load Banks
C-Series
-
C-series combined load banks are devices which contain resistive and reactive loads, apply the load to an electrical power source and dissipate the power of the electrical power.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
-
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Switchboard Instrument Voltmeter
ST-96
-
Standard Electric Works Co., Ltd
● Test Voltage : 2kV 50-60Hz● AC Ampere Over Load Scale：200%, 300%, 500%● Composition：Glass Window, ABS resin frame and case, Bakelite base● Color：Black case and frame, white scale plate and meter body● Pointer：Stick shape in black color● Pointer Length：55mm.
-
Product
Mezzanine System
5093
-
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
Product
VTAC, Patchcord, ITA, 36", VTAC, DACAR 535, to Rosenberger
7-141702731-036
-
The density/ thickness of DACAR 535 wire may require a module loading pattern that includes extra slot spacing to prevent wire bend and pressure. See the VTAC User Manual for more information.
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
AC-Powered, AC Voltage Monitor
VAA/VQA
-
NAI’s VAA and VQA are AC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
Product
E84 Handheld Tester
E84
-
The E84 Handheld Tester is the most efficient tool available for quickly testing, trouble-shooting, and resolving E84 problems. This self-contained, battery operated tool integrates the industry-leading automated load and unload routines provided in the E84 Emulator.
-
Product
PXI 6-Channel Battery Simulator Module
41-752-001
-
The 41-752 is a 6 channel battery simulator, each channel being capable of supplying up to 7V and 300mA to the load. Each channel is fully isolated from ground and from each other allowing the channels to be connected in series to simulate batteries arranged in a stacked architecture. The 750V isolation barrier permits the 41-752 to be used to create a lower power version of a battery stack representative of those used for vehicle propulsion.
-
Product
PXI 5A Power Multiplexer, 8-Bank, 5-Channel
40-651A-004
-
The 40-651A-004 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
PXI 10A Power Multiplexer, 1-Bank, 16-Channel
40-661A-103
-
The 40-661A-103 is a single pole, 1-bank, 16-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
Bench top Dielectric Withstand tester
HYPOT III
-
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
