Product

GPS/GNSS Antenna Signal Splitter 4-Way, TNC Female, IP67 Weatherproof, 1-2 GHz

GPS421

-

INSTOCK Wireless Components, Inc

GPS421 - INSTOCK Wireless Components, Inc

GPS421 is a four way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.

Product

AATCC Wrinkle Recovery Tester

-

TESTEX Testing Equipment Systems Ltd.

TESTEX Testing Equipment Systems Ltd.

AATCC Wrinkle Recovery Tester is used for determining a fabric’s ability to recover after wrinkling under a pre-determined load for a set period of time.

Product

Multi-Axis Sensors

-

Interface

Interface

Interface multi-axis sensors are designed to measure multiple forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment. Our 2-axis, 3-axis, 6-axis, and axial torsion load cells provide the ultimate in force and torque measurement. We can measure forces simultaneously in three mutually perpendicular axes, with the 6-axis load cells also measuring torque around those axes.

Product

Standard RF Power Sensors

-

Coaxial Dynamics

Coaxial Dynamics

Coaxial Dynamics "Standard" line of RF Power Sensors provide DC currents proportional to the forward and reflected power flowing through the line. All models are designed to drive a 30A, 1400-Ohm meter, or provide approximately 100 millivolts across a 5K load.

Product

Structural Durability Solutions

-

Instron

Instron

Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.

Product

Linear regulated power supply with thyristor pre-regulation

NTN

-

FuG Elektronik GmbH

NTN - FuG Elektronik GmbH

High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units

Product

Load Button Load Cells

-

Interface

Interface

Interface’s load button load cells are designed for customers who require the measurement of compression forces in a very low height space. They are designed to provide the most accuracy in as little space as possible. The smaller ConvexBT or LBMU can fulfill the need for force measurements at a very respectable precision level that is enough for most applications. Diameters range from ⅜ of an inch to just over 3 inches, with heights from ⅛ of an inch to 2 inches. The shaped load button has a spherical radius to help confine misaligned loads to the primary axis of the cell.

Product

Robotic Sample Loading Systems

-

Prior Scientific Inc.

Prior Scientific Inc.

Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.

Product

T3SP Time Domain Reflectometers

T3SP Series

-

Teledyne LeCroy

T3SP Series - Teledyne LeCroy

Teledyne Test Tools T3SP15D stimulates the DUT with true differential signals. The T3SP15D offers fast rise times of 35 ps for spatial impedance resolution (in FR4) of 3 mm, at DUT lengths up to 40 meters and TDR repetition rates up to 10 MHz and uses the same open short load thru (OSLT) calibration standards as vector network analyzers. With their small form factors, light weight, and optional internal batteries, the instruments go anywhere in test labs or in the field at an affordable price.

Product

Tribometers & Mechanical Testers

-

Bruker Nano Surfaces

Bruker Nano Surfaces

Research into materials and how materials can be changed to influence strength, integrity, or durability is an integral part of product design and improvement across nearly every industry. Bruker's mechanical testers and tribometers provide the most comprehensive and versatile means of investigating tribology—friction, wear, load, hardness, and lubrication.

Product

NO LOAD & LOAD TEST BENCH

-

International Biological Laboratories

International Biological Laboratories

These are the test benches incorporating control & measurement circuitry necessary for testing single phase as well as three phase transformers of several VA to MVA rating & voltage class of 11KV/433V,as well 33KV/11 KV, after manufacturing, repairing, reconditioning. Following tests can be done by these Test Sets.

Product

Bidirectional Weight Indicator

480

-

Interface

480 - Interface

Large 0.8 in LED 6-digit Display• 100,000 displayed graduations• 523,000 internal counts• Powers up to 10 Load Cells• Tension/Compression operation• NEMA 4X stainless steel enclosure• Measurement Rate up to 40Hz• Selectable filter settings• 0.1uV/graduation signal sensitivity

Product

General Purpose Low-side MOSFET Drivers

-

Renesas Electronics Corp.

Renesas Electronics Corp.

Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.

Product

Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T

MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041

-

Maschinenbau Haldenwang GmbH & Co. KG.

MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041 - Maschinenbau Haldenwang GmbH & Co. KG.

The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.

Product

AC Load Banks

XL1500 Series

-

Mosebach Manufacturing Company

XL1500 Series - Mosebach Manufacturing Company

The XL1500 Series of resistive load banks are designed for testing power supplies up to 1500kW of various voltages.

Product

3U VPX 1 Slot P&G w VITA 67.3C connector in J2

101V301P04-9003

-

ELMA Electronic, Inc.

101V301P04-9003 - ELMA Electronic, Inc.

Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.

Product

Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A

72-8690A

-

Tenma

72-8690A - Tenma

The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.

Product

Micro-Size Power Supplies

-

Advanced Energy

Advanced Energy

Advanced Energy’s micro-size, high voltage DC-to-DC converters offer a variety features — arc limits, tight line and load regulation, voltage monitoring, and more. Get the right solution in the perfect size.

Product

Current Transformers

-

Contrel Elettronica s.r.l. Company

Contrel Elettronica s.r.l. Company

We can supply current transformers (measure transformers, protection transformers and double ratio transformers, with analog output) with the following accuracy classes: 0.1, 0.2s, 0.5s; 1; 3. A wide range of combinations is available in our standard range with specific versions available upon request (other ratios, specific frequency, class or load). They are equipped with sealable terminal covers as standard.

Product

Universal Manipulators

-

esmo AG

esmo AG

optimized distribution of force allowing smooth and easy operationsminimized footprint/floor space in relation to manipulator load capacitymodular configuration ensuring "the perfect fit"

Product

Shaft Type Load Cell

KS

-

JFE Advantech Co., Ltd.

KS - JFE Advantech Co., Ltd.

Shaft Type Load Cell

Product

CPCI Load Boards 6Ux160mm

1940000135-0000

-

ELMA Electronic, Inc.

1940000135-0000 - ELMA Electronic, Inc.

The 6U cPCI Load Board functions to test a system's cooling capabilities by first applying the load to the power supply for verification and finally creating the necessary heat to confirm chassis cooling.

Product

Electrostatic Capacitance-Type Gap Detectors

VE series

-

Ono Sokki

VE series - Ono Sokki

VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.

Product

High Impedance Active Probes

34A

-

Picoprobe

34A - Picoprobe

Engineered to meet the stringent demands of advanced high frequency circuit designers. This high impedance probe combines full DC capability, rise/fall times of 120 ps, and a nominal loading input impedance of 10 megohm shunted by 0.1 pf. Signal attenuation is 20:1 with a 50 ohm oscilloscope input.