Clamps
-
product
Interconnect Adapters
Interconnect Adapters funnel wiring from modules to a VXI card. The adapter has removable side, top and bottom plates. Connector cover plates and cable clamps are ordered separately.VPC VXI adapters have been re-engineered to eliminate the need for punching holes in certain manufacturers cards. This design uses a clip that clamps down on the card's existing ejector tabs which firmly fastens the adapter to the card.
-
product
78-Pin D-Type Block Without Backshell
92-965-078-F
This connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
Leaky Insulator Detector (LID) Camera
CORONA CAMERA
The Leaky Insulator Detector (LID) is two-piece hand held non-destructive inspection system which utilizes AC/DC Current sensor and Ultrasonic technology for predictive maintenance. The Leaky Insulator Detector (LID) has a Flexible clamp sensor and Ultrasound Receiver.
-
product
Thermocouple Probes
Type T
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
product
AC Clamp Power Meter
CM3286 Series
Measure power ranging from 5 W at a low current of 60 mA to 360 kW. In addition to current, voltage, and power, measure simple integral power consumption and phase sequence. Discover manipulation of electric meters by comparing meter and integral power consumption measurements. Discover theft by measuring leakage current.
-
product
Clamping Voltage Tester
MIG0603CLV2
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
product
True RMS Low Current Clamp Meter
688
CLAMP METER We’ve greatly improved the zero drift on the low DC amps function - along with enlarging the clamp size to accomodate larger ground cables. The significant amount of feedback from our end user customers has contributed greatly in building this premium low current clamp meter. These features will be unmatched. Great tool for parasitic drain testing.
-
product
1-Watt Transmitter
VM-560FF
The VM-560FF Transmitter has one induction frequency; three direct connect and a fault-find frequency. The LED indicators on the transmitter show the frequency selected, output level, and battery status. An audio indicator beeps to advise the quality of the connection. This one-watt transmitter can transmit the locate signal onto the target line three ways. By direct connection, if direct access to the line is available, by induction by simply putting the transmitter in induction mode and placing it over the target line with the induction arrow in line with it or by clamp mode and using the induction clamp to clamp around the target line.
-
product
BP-1 PROBE
BP-1
Rugged ConstructionWater ResistantUnaffected by Surface CoverEasy to InstallZinc Plated Clamp (included in kit)
-
product
600A Dual Display TRMS-Clamp w/ Temp/Capacitance
DL579
UEi Test & Measurement Instruments
True-RMS Dual Display 600A HVAC/R Clamp Meter w/ Temperature & Capacitance
-
product
Handheld Meters
Omega carries a wide variety of handheld meters including anemometers, temperature and humidity meters, clamp meters, vibration meters, gauss meters, hardness meters and many more.
-
product
AC/DC Clamp Milliammeter (CE)
M-730
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current*Suitable for measurement of 4-20mA DC controlled circuit*DC mV analog signal output*Lowest influence from Magnetization and Terrestrial magnetism*Wide measuring ranges - up to DC 1000mA and AC10A*Sleeping current measurements for automotive electronics circuit*Jaw opening capability 30mmφ
-
product
5 KN Split-Drum Grips For Rope
These lower capacity 5 kN (1,100 lbf) split-drum grips are suitable for testing the tensile properties of rope and string with a diameter of 3 mm (0.12 in) or less. The diameter of the drum in the grips is 50 mm (2.0 in) and a spring mechanism is used to apply a clamping force through the split-drum to the specimen during testing.
-
product
68-Pin SCSI Micro-D Female Connector Block
92-965-068-F
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
High Insulation Digital Clamp Tester
HCL-5000KN+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
product
AC/DC Digital Clamp Meter
SK-7708
Up to 2000A AC/DC.Conductor dia, : Φ55mm max.True RMS."Power-on initialize" (auto zero adjustment).Peak hold, MAX/MIN measurements.Dust proof and water resistant.
-
product
Clamp Meter
ECLIPSE
ECLIPSE has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp is provided with a display with 6000 measuring spots with backlight and bargraph to allow for a simple reading even in poorly lit environments.
-
product
Probes
RTD
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
HFCT-34
MULTI MEASURING INSTRUMENTS Co., Ltd.
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
-
product
Standard Clamp Meters
For extreme temperatures, choose an analog clamp meter that can measure amps and volts without needing batteries.
-
product
Mini AC Leakage Current Clamp Tester (CE)
M-140
MULTI MEASURING INSTRUMENTS Co., Ltd.
*40mmφCT window and ultra compact size.*Least affection from the external magnetic field.*Wide current measurements.(AC0.01mA-300A)
-
product
1000 Amp AC/DC True RMS Digital Clamp Meter
DL6404
The top of the range DL6404 provides True RMS reading on AC current and AC voltages allowing accurate measurement regardless of the wave form. This makes it the ideal instrument for commercial and industrial applications where non linear loads are present.
-
product
TRMS AC/DC Clamp-on Power
HT9023
HT9023 has been designed to measure AC, DC AC+DC current up to 1000A in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp also measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.
-
product
Rotary Scale Clamp Meter
ST-375
Standard Electric Works Co., Ltd
● Designed for measuring AC current, AC voltage resistance and DC voltage .● Rotary scale which presents only one scale in windows at one time to avoid any possible reading errors.● Pointer lock function freezes the reading in dimly lit or hard to reach places.● Ω range ideal for checking the continuity or relays, transformers and motor coils.
-
product
TightSight™ Clamp Meter, 660A AC/DC W/TRMS
61-765
*TightSight™ bottom display*Tapered jaws with hook tip*True RMS current and voltage*AC/DC voltage*Audible continuity*High frequency rejection**Peak hold*Max/min hold*Data hold*Selectable audible and visual alerts when potentially hazardous voltages are detected at the probe terminals*Selectable auto power off*Backlit display*Low battery indicator*Reads accurately on noisy electrical circuits
-
product
Digital Clamp Meter
A clamp meter is convenient for measuring instruments that allows the measurement of current simply by clamping a wire while being energized without cutting a circuit. In cases of measurement by a multitester and digital multimeter, the circuit must be cut to measure current. In contrast, with a clamp meter, current can be measured simply by clamping a live wire over its sheath. In addition to its simple operation, it allows safe measurement of a higher current.
-
product
1000A AC Clamp Meter
CM55
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
product
Crease Recovery Tester
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester, to determining recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC), After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded. Fabric Crease Tester complies with ISO 2313, AATCC 66, BS EN 22313， etc.
-
product
Signal Evaluation Systems
*Integrated flow, temperature and wire monitoring*Adjustable switching outputs for monitoring flow and temperature*Clearly visible multi-color LED bargraph display*Signal output via potential-free relay contacts*Connection options: Insulation displacement / screw terminals and cage clamps
-
product
Air Permeability Tester
TF164B
TESTEX Testing Equipment Systems Ltd.
Our Air Permeability Tester determines the resistance of fabrics (woven, knitted and non-woven textile materials) to the passage of air (air flow) under constant pre-set air pressure while firmly clamped in the test rig of selected test head/area.The specimen is loaded to the test area of the instrument easily by means of a pneumatic holder. By pressing down the holder to start the test. The air permeability tester is equipped with a vacuum pump to draw air through an automatic interchangeable test head with a circular opening. The pre-selected test pressure is automatically maintained, and after a few seconds the air permeability of the test specimen is digitally displayed in the pre-selected unit of measure on the touch panel after test the holder is released and the vacuum pump is shut off.
