-
Product
Boards
MIL-STD-1760
-
The MIL-STD-1760 interface card is compatible with all common variations of MIL-STD-1760 and provides a wide range of features normally found only on full size testers. The cards can operate simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection.
-
Product
Load Boards
-
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
Product
Sonar Boards
-
Low skew between channelsMulti-Board SynchronizationSigma-Delta and Delta-Sigma Analog InputOutput reconstruction filtersUp to 64 Channels per BoardProgrammable Sampling Rates to 500K SPSAuto-CalibrationResolutions: 16-bit, 20-bit, and 24-bitAsk about other features such as GPS Synchronization
-
Product
Termination Boards
-
Termination Boards for DCS Distributed Control Systems. Available in a wide variety of analog, digital, RTD, and relay options. These boards are for analog input and output modules. It is a general termination board for most kind of analog modules. There are various sizes of boards for users to choose from.
-
-
Product
PCI Daughter Boards
DB-8R
-
The DB-8R board is the I/O connection board designed for PISO-PS300 and SERVO-300. It is also equipped with 8 form A relays to provide higher current switching capability.
-
Product
PCI Daughter Boards
DB-24PR/24/DIN (with DIN-Rail mounting kit)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
cPCI Load Boards
-
VECTOR Electronics and Technology, Inc.
Vector Electronics & Technology, Inc. cPCI resistive load boards provide a means to test power generated and cooling capability of cPCI systems.
-
Product
ISI Channel Boards
M8049A
ISI (Intersymbol Interference) Channel Board
The M8049A ISI channel boards can be used to emulate channel loss in receiver test setups. The boards are used to emulate channel loss for data rates of 32 Gb/s and higher. A choice of 21 PC board traces with different lengths can be inserted into the signal path. The trace lengths range from 0.8 inch (20.3 mm) to 22.3 inch (566.4 mm). By cascading the traces within one board or with another board, a wide range of channels can be emulated with very fine resolution of insertion loss steps. With their small size the ISI channel boards can be located closely to the device under test.
-
Product
PCI Daughter Boards
DN-8237
-
DN-8237 is the kit that includes the breakout board and cable for I-8092F. It includes a din rail mountable daughter board (wiring terminal board) for I-8092F and CA-3710D Male D-sub cable 1M Cable for Daughter Board(180°). I-8092F is a 2-axis stepping/pulse-type servo motor control module that can be used on any of the ICPDAS I- 8000, Wincon, and Lincon series controllers, and is suitable for general-purpose motion applications.
-
-
-
-
Product
Sampling Boards
MSXB 028
-
Simultaneous Sampling Boards are used in multichannel spectral analysis and other applications that require simultaneous acquisition of several channels. The MSXB 028 usually is used for applications that require interchannel phase measurements such as applications that perform transfer function computations. This board eliminates phase error introduced by sequential sampling.
-
Product
Breakout Boards
D Series Boards
-
D Series Breakout Boards are open designs that provide signal access when troubleshooting. Signal connections are accomplished by inserting or removing Mini-Jumper plugs. All normal and high density D type connectors are available. Current carry capability is from 2.25A to 5.3A. Normal Density D Type: 9, 15, 25, 37 and 50 positionsHigh Density D Type: 15, 26, 44, 62, 78 and 104 positions
-
-
Product
Daughter Boards
-
ICP DAS USA offers a wide array of PCI based daughter boards that can be used in PC's in industrial environments. PCI series are top-of-the-line and reach awesome performance with multiple functions and high resolutions. And the PISO series is putting emphasis on its protection ability to prevent signal input from direct impact.
-
Product
PCI Express Serial Boards
-
Sealevel PCI Express serial boards utilize 120-byte FIFOs for maximum reliability in data-intensive applications. Software developed for standard PCI boards will also work with Sealevel PCI Express boards, simplifying your transition to this next-generation PCI bus. Sealevel PCIe serial boards are configurable for RS-232, RS-422, and RS-485 electrical interfaces. These PCIe serial boards are fully compatible with X2, X4, X8, X16, and X32 PCI Express slots.
-
Product
PCI Daughter Boards
DB-8225/2 (with 2 meter D-Sub 37-pin cable)
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
Multiple Digital Expansion Boards
MSXB 038
-
Multiple Digital Expansion Boards can be connected to a single DAP for a total of 128 digital input lines and 1024 digital output lines. Input expansion is at a maximum with eight MSXB 038 boards (128 points). Output can be expanded to 1024 points by connecting 64 MSXB 038 boards to a single DAP.
-
Product
Boards
MIL-STD-1553
-
The MIL-STD-1553 multi function interface cards are compatible with all common variations of MIL-STD-1553 and provides a wide range of features normally found only on full size testers. The card can operate simultaneously as a Bus Controller (BC) and/or multiple (up to 32) Remote Terminals (RT), or as a Triggerable Bus Monitor. The card supports error injection and detection.
-
Product
PCIe Carrier Boards
-
These non-intelligent carrier cards interface XMC and PMC mezzanine modules and Industry Pack Modules to a PCI Express bus in a PC-based embedded computer.
-
Product
Carrier Boards
ROM-DB7501
Carrier Board
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
Product
3U CPCI CPU Boards
-
Advantech 3U CPCI boards are Intel based CPU blades that support single or dual processors that fully utilize I/O features of Intel® chipsets.
-
Product
Prototype PCBS Printed Circuit Boards
-
Prototype printed circuit boards are manufactured for a variety of reasons; often it is important to manufacture these circuit boards to perform various tests before going through with a full PCB production run. When it comes to prototype PCB boards it’s important to get them made using high quality standards.
-
Product
Development Boards
-
Everything From Full-Featured to Tiny Starter Boards. Professional, full-featured development platforms, rich in modules. Each Easy Board features on-board programmer or debugger, and supports an entire family range of microcontrollers.
-
Product
PC/104 CPU Boards & I/O Modules
-
Advantech's PC/104 CPU boards feature a compact size, ultra-low power consumption, and PC/104, PCI-104, or PC/104-Plus expansion with extended temperature support and high vibration/shock tolerance (MIL-STD certified).
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
PCI Express Digital I/O Boards
PEX-P16R16i
-
PCI Express x1, 16-channel Isolated Digital Input, 16-channel Relay Output Includes one CA-4037W cable and two CA-4002 D-Sub connectors, supports operating temperatures from 0 ~ 60°C. (Formerly PISO-P16R16E).
-
Product
PCI Daughter Boards
DB-1825/2 (Daughter Board for PCI-1202/1602/1802/822/826 )
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
