TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
Wideband Distributed Amplifiers
-
Analog Devices GaAs MMIC-based wideband distributed amplifiers cover the dc to 65 GHz frequency range in various ultrawide bandwidths. Our design catalog includes low noise amplifiers, power amplifiers, and driver amplifier designs to meet your needs in applications such as electronic warfare, radar, electronic countermeasures, optical applications, and instrumentation. To meet diverse design requirements, some of our LNAs also offer internal-self biasing that requires only a signal drain voltage to operate.
-
Product
Instrumentation (Tacho) Amplifier
MS 2007
-
Instrumentation Amplifier is a customized unit to incorporate additional line filtering and spike suppression so that the amplifiers can operate directly off the main aircraft 28 volt system and amplifies the input signal according dynamic input configuration. This unit is capable of working without damage in both under and over voltage conditions. Designed for general aircraft applications.
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
Synchronization and Distribution Amplifier - PCIe
Model 7892
-
The Model 7892 High-Speed Synchronizer and Distribution PCIe Board synchronizes multiple Pentek Cobalt or Onyx boards within a system. It enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP, and software radio applications
-
Product
Precision Amplifier
-
TI Precision Labs is the electronics industry's first comprehensive online classroom for analog engineers. The on-demand curriculum pairs theory and applied lab exercises to deepen the technical expertise of experienced engineers and accelerate the development of those early in their career. This free modular curriculum includes over 30 hands-on trainings and lab videos, covering analog amplifier design considerations with online course work.
-
-
Product
Headphone Amplifiers
-
A top-of-the-line headphone/earphone amplifier designed for precise professional audio monitoring.
-
Product
Tower Mounted Amplifiers
-
*Available twin and single TMA configurations*Low band, high band & dual band units, including AWS & WCS*High linearity, dual duplexed, light weight design*AISG 2.0 compliant
-
-
Product
Variable Gain Optical Amplifier Module
VGA4500-FM06
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4500-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
ADC Drivers Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
Power Amplifiers
Immunity
-
The RF power amplifier range from Laplace is specifically designed for EMC Immunity testing according to IEC61000-4-3 and IEC61000-4-6. These are compact units with characteristics matched to the requirements of IEC standards. These RF amplifiers utilize fully isolated linear MOSFET or advanced GaAs FET devices, which provide high gain, wide dynamic range and excellent third order intercepts. High efficiency and reliable operation are achieved by employing unique RF combining circuits, RF microstrip networks, sophisticated thermal design, custom machined housing and heavy duty components. The high power RF amplifiers undergo extensive burn-in prior to final test and inspection.
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
Millimeter-Wave Amplifiers
-
When your application requires operating at Ka-band and above, trust Mercury Systems’ millimeter wave amplifiers to perform. With standard designs up to 65GHz and custom products available, Mercury is ready to support your high frequency requirement.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
-
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
Operational Amplifier
Op Amp Series
-
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
Class-D Audio Amplifiers
-
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
Product
EDFA Amplifier
-
A line of Gain Flattening Erbium-Doped Fiber Amplifiers are designed for in-line amplification of DWDM networks. When a standard EDFA is used to amplify multi-channel DWDM signals, the output power level of various channels will vary according to the gain profile of the erbium fiber. This gain variation can be as great as 6 dB in magnitude. The EDFA-GB-R is unique in its dual-stage amplification and internal Gain Flattening Filter (GFF) to compensate the erbium fiber gain variation.
-
Product
Millimeter Wave Amplifiers
-
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
Product
High Voltage, High Current Linear Amplifier
P100
-
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
Product
Standard Amplifiers
-
Teledyne RF & Microwave, a Business Unit of Teledyne Microwave Solutions (TMS), supplies catalog and custom RF and microwave amplifier designs for aerospace, defense, and industrial applications. These standard amplifiers, originally designed by Teledyne Cougar, provide both excellent stability and cascadability.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
Air Amplifiers
-
Nex Flow® Air amplifiers are compact, low cost air flow “movers” that are virtually maintenance free. Applications include the venting of fumes and smoke, conveying of low weight materials, and entraining a high volume of air to cool, blow off, and dry. Air Amplfiiers use the “Coanda effect” to draw in the surrounding atmosphereic air while consuming only aminimal amount of compressed air. These products can amplify airflow up to 17 times (depending on the size) resulting in dramatcally reduced levels of noise. Air Amplifiers (also called Air Movers) draw in atmospheric air from the back of the unit as well as having downstream entrainment further amplifying the flow. They are used for cooling and venting. While the force produced for blow off decreases as the amplifier outlet diameter increases, these Air Movers are ideal for cooling because of the high velocity outlet fow and and are much more effective for cooling compaed to air nozzles.
-
Product
Semiconductor Power Amplifiers : Solid State Power Amplifiers (SSPA) For Indoor (rack-mount) And Outdoor (hub-mount) Settings
-
Insight Product Company is proud to offer state-of-the-art semiconductor (solid state) power amplifiers that are compact, rugged, and deliver immense power, and expectional frequency stability and minimal phase noise. These solid state power amplifiers are ideal for indoor, rack-mount, or outdoor, hub-mount, applications. We offer S-band, C-band, X-band, and Ku-band amplifiers, with output power of upto 1,000 Watts (varies based on frequency band).
-
Product
In-Line Charge Amplifiers
-
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
Product
6-Channel VME Pulse Amplifier
V860
-
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
Product
Telecom Optical Amplifiers
-
Thorlabs' optical amplifiers for telecom applications are available as complete benchtop systems or as pigtailed butterfly packages. Our line of benchtop optical amplifiers includes a praseodymium-doped fluoride fiber amplifier (PDFA) and erbium-doped fiber amplifiers (EDFAs). Our optical amplifiers available in pigtailed butterfly packages include InP/InGaAsP or GaAs/InGaAs semiconductor optical amplifiers (BOAs or SOAs), and high-speed optical switches.
