Product

Outdoor Infrared Motion Sensor

ENVIROMUX-IMD-O

-

Network Technologies Inc

ENVIROMUX-IMD-O - Network Technologies Inc

Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.

Product

Medical Mask Gas Exchange Pressure Difference Tester

DRK371-II

-

Shandong Drick Instruments Co., Ltd.

DRK371-II - Shandong Drick Instruments Co., Ltd.

It is used to measure the gas exchange pressure difference of medical surgical masks and other products.

Product

Face Masks Particulate Filtration Efficiency PFE Tester

GLE-20

-

Lisun Electronics Inc.

GLE-20 - Lisun Electronics Inc.

GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.

Product

Preamplifiers

LNA Series

-

Teseq AG

LNA Series - Teseq AG

Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.

Product

Copper PCB

-

Amitron Corp.

Amitron Corp.

The Amitron process is capable of producing 20 plus ounces of finished copper and reliably spray coat a protective and consistent solder mask with imaged nomenclature. Amitron utilizes a unique process referred to as "Laminated Deposition". This combination of processes allows extreme copper thickness requirements to become very practical and cost effective. The process utilizes heavy base copper that when placed in our plating and etching systems will deliver consistent and reliable high power circuits.

Product

Flexoplate Analysis

-

Quality Engineering Associates Inc.

Quality Engineering Associates Inc.

QEA has the most comprehensive and sophisticated lineup of evaluation tools for flexography, one of the fastest-growing sectors in commercial printing. Our test tools quantify flexo plates, film, masks, photopolymer- and metal-backed plates and sleeves, letterpress, newsprint and direct-engraved plates, as well as the final print.

Product

ARINC-style Attitude Gyroscopes

1U367-series

-

Sigma Tek, Inc.

1U367-series - Sigma Tek, Inc.

The 1U367 has a pictorial horizon mask and a fixed airplane. The mask moves to indicate climb, dive, and bank. Bank and pitch attitudes are diaplayed so that the pilot's sensing of the gyro's horizon indication is the same as the interpretation of the relationship between the wings of the aircraft and the natural horizon during visual flight.

Product

MASK DR-SEM

-

Advantest Corp.

Advantest Corp.

Our defect review SEM tools perform detailed reviews of minute defects on photomasks.

Product

Pico Oscilloscope Range

-

Pico Technology Ltd.

Pico Technology Ltd.

High-end features such as serial decoding and mask limit testing are included as standard.

Product

Lithography

-

EV Group

EV Group

EVG’s key competencies in lithographic technology lie in the high-throughput contact and proximity exposure capabilities of its mask aligners and its newly developed, revolutionary and highly versatile maskless exposure lithography systems. These capabilities are complemented by its resist coating and resist development systems with advanced in-house process competences and hands-on development skills.

Product

Enhanced Time-Domain Analysis With TDR

S95011B

-

Keysight Technologies

S95011B - Keysight Technologies

This application enables the analyzer to perform enhanced time domain analysis for high-speed data applications. All functionality of the S95010B are included (TDR/TDT mode). In addition, the S95011B enables more detailed measurements and evaluations, such as eye-diagram / mask modes, without adding PLTS software. Jitter and emphasis / equalization capabilities enable simulation of real-world signals and environment. The S95011B covers up to 53 GHz bandwidth. Full calibration is available and the automatic deskew ensures easy removal of fixture and probe effects. To get the best accuracy, mechanical calibration kits or ECal with DC option (i.e., N469xD or N4433D with Option 0DC) are recommended.

Product

Eurocard Plugbord

4615

-

VECTOR Electronics and Technology, Inc.

4615 - VECTOR Electronics and Technology, Inc.

6U x 160mm Eurocard size for 96-pin DIN connectors. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads (0.28” x 0.080”) for interconnecting multiplecomponent leads.Interleaved buses on both sides, back-to-back. Pad and bus surfaces solder-coated for user convenience.Green Solder Mask both sides. Row and column legends provided.

Product

Automated Front & Backside Mask Aligner System

Model 6000

-

OAI

Model 6000 - OAI

With over 4 decades of manufacturing in the semiconductor industry, OAI meets the growing challenge of a dynamic market with an elite class of production photolithography equipment. Built on the proven OAI modular platform, the Model 6000 has front and backside alignment that is fully automated with a submicron printing capability as well as submicron top to bottom front side alignment accuracy which delivers performance that is unmatched at any price. Choose either topside or optional backside alignment which uses OAI’s customized advanced recognition pattern software. These Mask Aligners have OAI’s Advanced Beam Optics with better than ±3% uniformity and a throughput of 200 wafers per hour in first mask mode, which results in higher yields. The Series 6000 can handle a wide variety of wafers from thick and bonded substrates (up to 7000 microns), warped wafers (up to 7 mm-10mm), thin substrates (down to 100 micron thick), and thick photo resist.

Product

GAOTek Portable H/L Voltage Clamp Current Leaker

GT00YA00ZX

-

GAO Tek Inc.

GT00YA00ZX - GAO Tek Inc.

The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.

Product

Medical Masks Differential Pressure Tester

-

Sataton Instruments Technology CO., Ltd

Sataton Instruments Technology CO., Ltd

Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.

Product

Thyristors Application Specific Devices

-

STMicroelectronics

STMicroelectronics

A.S.D. (Application Specific Discretes) technology is a vertical integrated power technology using a full planar process. By applying the masking process on both sides of the chip, higher current density is achievable than is possible with epitaxial base or horizontal structures.

Product

Plus Super Phosphor Oscilloscopes

SDS2000X

-

SIGLENT Technologies

SDS2000X - SIGLENT Technologies

The SDS2000X Plus series employs SIGLENT’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications which require more than 8-bit resolution.