Voltage Converters
Changes the voltage of a source.
-
product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
product
NI-9239 , ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780181-01
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
product
POL Converter
Renesas offers a rich product lineup focused on the step-down type switching power supplies with built-in FET from small current applications to large current applications, depending on the supplied current.
-
product
E/O Converter
LTX-510
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
-
-
product
Frequency Converter
Our frequency converters, which we offer with outputs of up to 500 kVA, can be used to supply alternating current consumers with constant voltages that deviate from the input network.
-
product
Photometric Converter
C4000
The C4000 converter is a multi channel controller capable of operating all optek photometric sensors. The C4000 converter allows for easy programming and operation, and can supply up to four real time configurable 4-20 mA output values correlated to any units of measure. The C4000 offers configurable relay alarms, can record and download process data, and can operate up to four sensors simultaneously.
-
product
Converter
556
The dual channel converter 556 provides continuous inline, real-time measurement and control of turbidity. The customer’s specific factory calibration of the converter can be configured in ppm (DE), FTU or EBC. Combined with an optek TF56-N scattered light sensor the 556 converter is a cost-saving measuring system, providing reliable process measurements.
-
-
product
Optical-Electrical Converter - MATRIQ
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
NI-9244, 400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783106-01
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
-
product
DC Converter
Primary switched DC converter modules are used, among other things, to generate different (consumer) voltage levels from central DC voltages, also battery-supported.
-
product
O/E Converter
TIA-1200
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
product
F/V Converter
FV-1100
The FV-1100 receives signal from a rotation detector or a similar device and outputs DC current or voltage signal proportional to its frequency. As the fluctuation of the input frequency signal is continuously converted to DC voltage, it is useful for measurement and recording of transient phenomena such as fluctuation of rotating speed, current velocity, frequency.
-
product
Interface Converter
ZET 7177
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
product
D/A Converter
DA-4130
The DA-4130 D/A converter converts BCD output signal from Ono Sokki's digital gauge DG-4000 series, RV series reversible counter or other devices into analog signal to be recorded with pen recorder, etc.
-
product
Binary to BCD Converter
BAC600
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
product
Plane Wave Converter
PWC200
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
product
Single Phase Converter
Series Sirio AC / ACS
The SIRIO single-phase equaliser is an electronic device that offers the ability to regulate the rms value of a sinusoidal voltage through the control of two diodes connected in antiparallel.
-
product
Industrial Media Converters
Advantech's industrial media converters can convert Ethernet data and power into fiber optic signals. They also offer Link Fault Pass-Through (LFPT).
-
product
WIFI Converter
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
product
DC-DC Converters
TDK-Lambda is a global supplier of DC-DC converters with a broad range of power levels. The commercial off the shelf power solutions encompass industry standard board mounted products to chassis mount configurations for the Industrial, Healthcare, Information and Communications Technology (ICT), and Avionics and Defense markets.
-
product
Interface & Level Converters
Advanced Science and Novel Technology, Co., Inc.
2-channel LVDS-to-CMOS converter (Receiver) and 2-channel CMOS-to-LVDS converter (Transmitter)Optional signal splitter function with selectable inversionOptional DS (Data/Strobe) encoding/decoding for compatibility with Space Wire StandardProgrammable LVDS/CML/ECL Receiver input interfaceTrue LVDS Transmitter output interfaceFlexible selection of enabling and operational modes of the channelsHigh-impedance states of disabled CMOS outputsSingle +3.3V power supplyIndustrial temperature range
-
product
Fiber Optic/BNC Converters
The active receiver and transmitter require power while the passive transmitter requires a TTL signal that is capable of driving 75 mA.
-
product
4-20mA Sensor Converter
ENVIROMUX-S420MA-24V
External RJ45 device monitors up to two 4-20 mA analog sensors. Supports ISA Type 2, ISA Type 3, and ISA Type 4 sensors. Provides 24VDC, 25mA for each sensor. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 500 ft. (152 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
product
DC-DC Converters
Samlex America, Inc Power Supplies
Fully Isolated Regulated DC-DC converters provide stable 12V -12V or 24V-24V regulated output power for situations with an unstable input source.
-
product
Voltage Protection
Are solid state voltage sensing relays with electromechanical output contacts built in a fully draw out case format. Designed for application on AC & DC voltage systems, these relays are ideally suited to monitor power supply voltage levels wherever high accuracy and reliable, maintenance free operation is essential. All power to operate the relays is derived from the sensed input voltage therefore an auxiliary supply is not required.
-
product
Analog-To-Digital Converters
Teledyne e2v has been innovating data converter technologies for over 20 years and offer a range of analog-to-digital converters that feature:Latency as low as 5 nsUp to 4 channels at microwave frequenciesLowest noise vs. performance on the market at microwave frequenciesThe cutting-edge technology packed into Teledyne e2v's data converters allow our customers to significantly simplify designs with licence free, standard and customized solutions.
-
product
Frontends & Converter
FExx Series
R&S®FExx external frontends extend the frequency ranges of Rohde & Schwarz signal and spectrum analyzers and signal generators up to 170 GHz. The R&S®FExx enables the up and down-conversion of the signal directly at the DUT. In an OTA environment it lowers cable losses, increases sensitivity and delivers more power at the antenna.
-
product
Voltage Probes
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.
