Corrosion
gradual degradation of a material over time
See Also: Salt Spray, Salt, Salt Fog, Corrosion Test
-
Product
Ultrasonic Clamp-On Flow Sensor
SEMIFLOW CO.65
-
SEMIFLOW CO.65 non-contact clamp-on flow sensors are ideal to measure abrasive, adherent, corrosive, and ultra-pure liquids on rigid plastic tubes and pipes used in the semiconductor industry. Equipped with an integrated electronic unit, they function as a complete flow meter in the size of a small transducer without an external board or transmitter.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
Cross Sections and Metallography
-
Rocky Mountain Laboratories, Inc.
Cross sections are prepared by mounting samples in epoxy and then grinding and polishing the mount for imaging in the optical microscope or Scanning Electron Microscopy (SEM). Valuable information from cross sectioning can include: film thicknesses, inclusions, corrosion thickness, dimensional verification, and subsurface defects. Metallographic cross sections are typically etched to reveal the microstructure. Microstructural analysis can provide information about heat treatment history, corrosion susceptibility, as well as undesirable microconstituents.
-
Product
Rope Testers
-
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
Product
CORROSION GAUGE
MX-3
-
With the hand held MX-3 Ultrasonic micrometer, you can make reliable measurements or scan a length of material for the thinnest point. The tool's backlit display is easy to read, even in dim light, and the unit operates for up to 200 hours on a single set of batteries. The MX-3 comes complete, ready to use and is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
Flow Wet-Tap Valve
3519
-
The Signet 3519 Flow Wet-Tap Valve serves as a unique interface between the installation fitting and the wet-tap style Signet 515 or 2536 Rotor-X Flow Sensor. It provides a fast method of removing the sensor from the pipe under specified operating pressures. The PVC and stainless steel design of Wet-Tap makes it resistant to corrosion and chemical attack by acids, alkalis, salt, and a number of other harsh chemicals.
-
Product
Radar Level Sensor
VRS-20
-
Versatile and simple to install, the VRS-20 has been developed by Valeport to work seamlessly with the TideMaster Tide Display/Logger and other third party data loggers using RS232, RS485 and SDI-12 communication. Non-contact technology removes the installation, corrosion & fouling issues of submerged sensors, while simplifying datum control. Accuracy and performance are unaffected by changes in water density and atmospheric conditions.
-
Product
Digital Surface Profile Gauge
-
Backed by the sound experience of this industry, we have been able to offer an unmatchable assortment of Digital Surface Profile Gauge. Offered gauge by us will allow quick measurements of the top to bottom height of blast cleaned surfaces to be accurately measured. In addition to that, this gauge can also be used to measure the effects of corrosion. Known for its light weight and simple design, offered gauge is highly useful and user-friendly tool for paint, coating, and corrosion inspection.
-
Product
Tilt Position Sensors
-
Available with any measurement angle between 15 and 160 the P603 tilt sensor operates a gravity driven, oil damped pendulum with a very low settle time and durable housing. Our tilt sensor has proved popular in marine applications because like our linear and rotary sensors we have used highly durable and corrosion resistant materials.We also offer the S623 which is waterproof sealed for continual submersion to IP68 350bar, 5000psi, 3500msw
-
Product
Salt Spray Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Salt spray chamber is intended to use method of salt-spray corrosion to evaluate the performance of corrosion resistance of specimens to salt fog under the specified conditions. It is capable of simulating a locally salt mist environment in which the test piece is placed. There are different types of salt fog chambers including microprocessor digital version, touch-screen control version and compound version featuring temperature&humidity control and adjustment. widely applied to components and parts, electronics elements, metal materials etc.
-
Product
Graphite Sheet Electrodes
OT1-2
-
High-purity graphite sheet electrodes for electrochemical research, current collectors, electrocatalysis and corrosion testing. Custom sheet dimensions, exposed areas, mounting holes and lead-connection options are available for laboratory cell designs.
-
Product
Salt Spray Testing/Cabinet Based Corrosion Testing
-
Sometimes referred to salt mist, salt fog, humidity or corrosion testingAll corrosion and environmental related tests can be tailored to customer requirementsTypical exposure times range from 16 hours to over 1000 hoursAccelerated corrosion testing can be used to check protective coatings, surface finishes and material compatibilitiesOur facilities provide a continuous controlled corrosive exposure and can combine salt spray and humidity environments.
-
Product
Scanning Probe Workstations
-
BioLogic has over 25 years of experience producing scanning probe electrochemistry instruments. Initially this included a number of single technique instruments, with the first modular scanning electrochemical workstation, the M370, introduced in 2006, under the Uniscan name.Scanning probe electrochemistry has found use in academic and commercial research settings. It is applicable in any field in which bulk electrochemical measurements have been used. Scanning probe electrochemistry has found widespread use in: Corrosion and coatings, Biology, including biosensors and biotechnology, Batteries, fuel cells and photovoltaics, Materials, Catalysis
-
Product
Portable Sulphuric Acid Dewpoint Temperature Monitor
-
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
Product
Chloride/Sulfate Analyzer
Thornton 3000CS
-
The METTLER TOLEDO Thornton 3000CS Analyzer is an on-line instrument for direct measurement of chlorides and sulfates in pure water and power cycle chemistry samples. The analyzer continuously monitors these highly corrosive contaminants to assist in corrosion control and minimizing damage to critical power plant equipment. Early, unambiguous detection of trace levels of chloride and sulfate ions is provided with minimal operator supervision.
-
Product
ISO Scratching Tool
1537
-
The Elcometer 1537 ISO Scratching Tool is a simple but effective instrument that is used to scratch the surface of samples in preparation for adhesion, salt spray and corrosion tests.
-
Product
Benchtop Electric Blast Drying Oven
-
Guangdong Test EQ Equipment co., Ltd.
- Precision & Uniformity: Multi-zone airflow design ensures ±2% temperature uniformity (per ASTM E1459). Auto-reversing fan eliminates hot/cold spots.- Rapid Drying: Turbo blast mode reduces drying time by 50% vs. conventional ovens (ideal for ceramics, polymers, and PCB coatings).- Durability: SUS304 stainless steel chamber, fiberglass insulation, and powder-coated exterior for corrosion resistance.- Smart Connectivity: IoT-enabled remote monitoring via mobile app (iOS/Android), compliance with FDA 21 CFR Part 11 for audit trails.- Energy Efficiency: ECO mode reduces power consumption by 30% during idle (ENERGY STAR® 2025 certified).
-
Product
Harmonic Filter Resistors
-
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
Product
Salt Spray Machine
UI-E01A
-
Salt Spray Machine – Salt Spray Test Chamber is used to test material Corrosion resistance by producing salt fog. So it is also called salt fog test chamber. This salt spray cabinet is widely used in painting, coating and other industries. Salt Spray Test Method includes ASTM B117, B268, CNS 3627, 3885, 4159, 7669, 8886, JIS D-0201, H-8502, H-8610, K-5400, Z-2371, ISO3768, 3769, 3770, GB/T2423, GJB 150 and etc.
-
Product
Bimetal Thermometer
BT
-
Series BT Bimetal Thermometers offer accurate, reliable service even in the toughest environments. These corrosion resistant units are constructed from stainless steel and are hermetically sealed to prevent crystal fogging.
-
Product
CORROSION GAUGE
MVX
-
The MVX finishes the line of MX gauges with class. This thing is loaded with all of the features of the MX gauges and a lot more. Four selectable display options: RF, Rectified, B-Scan, and Large Digits. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and auto waveform find just to mention a few! Equipped with a single element flaw prove-up mode for basic angle beam inspections. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVXview java-based PC software makes this thing a complete kit, and then some!
-
Product
Unsealed Jacketed Electrochemical Cell – Temperature-Controlled
DL-1
-
DL-1 Unsealed Jacketed Electrochemical Cell – Temperature-Controlled is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model. The cell can be matched with working electrodes, reference electrodes, counter electrodes, gas ports, quartz windows, PTFE covers, jackets, and custom fittings according to the experimental setup. Please confirm the required volume, sealing method, electrode ports, and application conditions before ordering.
-
Product
Compact Coating Thickness Gauges
MP0 Series
-
The small all-rounders for mobile coating thickness measurement. Leading industrial instrument series for fast and easy coating thickness measurement in corrosion protection and industrial applications.
-
Product
Salt Spray Test Environmental Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Salt spray chamber is used to test materials likes paints, electroplating, non-organic, pastry film, anode treatment and rust prevention oil’s corrosion resistance performance. Besides, anti-corrosion treatment of various materials to make their products resistant to corrosion.
-
Product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
-
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions. .The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Reach-In Humidity Test Chamber
-
The Humidity Test Chambers from Weiber are corrosion test chambers that are used to simulate high or low humidity conditions for testing the rust preventing capacity of various oils and greases. These high low humidity simulation chambers find wide spread usage in research organizations, educational institutions and industrial units and are most commonly employed by petroleum and chemical industries.
-
Product
Insulating Oil Testing
-
Weshine Electric Manufacturing Co., Ltd
Weshine represent the absolute best in the field of transformer oil regeneration and corrosive sulfur removal. Several new features developed inhouse by our research and development department result in the state-of-the-art transformer oil regeneration equipment. Supplemented by our unique corrosive sulfur mitigation process integrated directly into the regeneration process.
-
Product
Small Corrosion Test Electrochemical Cell – 30ml / 80ml
SCT-1
-
Small corrosion test electrochemical cell (8–80ml) with 2 electrode ports, borosilicate + PTFE body, and integrated graphite and Ag/AgCl electrodes. Temp range: RT–60°C.
-
Product
Dissolved Carbon Dioxide (DI-CO2) Ultrapure Water Delivery System
-
The DI-CO2 is used in single substrate cleaning tools for rinsing steps to prevent ESD effects and/or corrosion by creating UPW (ultrapure water) with precisely defined conductivity. It is a compact system for tool integration, providing conductive DI-CO2 water (Carbon Dioxide) with closed loop controlled conductivity. The conductivity is kept at a constant value under changing flow conditions by control of the CO2 concentration in the DI-CO2 water.
-
Product
ECHO 8 Ultrasonic Corrosion and Precision Thickness Gage
ECHO 8
-
Danatronics offers our newest ultrasonic precision thickness gage line, the ECHO 8 series. ECHO 8 represents our most advanced thickness gage ever combining dual and single element transducers all in one small package. ECHO 8 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of dual, contact, delay line and immersion transducers from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD card memory and interface to Microsoft excel. The ECHO 8 is available in 4 models including the ECHO 8, ECHO 8DL, ECHO 8W and ECHO 8DLW. The vibrate on alarm feature is the world’s first and is great for loud environments
