Test Switches
-
Product
PXI 8 Slot BRIC 99x16 2-pole (9 sub-cards)
40-562A-122-99X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Dual 8 Channel Switch Simulator
40-485-121
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
PXI 2-Slot High Density 2A BRIC Matrix, 29x8 2-Pole (1 Sub-card)
40-573-202-29X8
Matrix Switch Module
The 40-573-202-29x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
Product
Keysight Dual 4x8 Armature Matrix for 34980A
34931A
Matrix Switch Module
The Keysight 34931A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x8, 8x8, or 4x16 configurations 64 2-wire cross-points Connections to the internal DMM Expandable via four 2-wire analog buses Relay counter Latching armature relays 300 V, 1 A switch; 2 A carry current
-
Product
PXI BRIC8 FIBO Matrix Dual 120x4 3pin brkout
40-592A-106
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI 8 Slot BRIC 460x8 1-Pole Dual Analog Bus (10 sub-cards)
40-560A-121-460X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8x4 RF Matrix 300MHz 50Ω Multiway Connector
40-729-002
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI 4-Slot BRIC Matrix, 88x4 2-Pole (2 Sub-cards)
40-562B-022-88X4
Matrix Switch Module
The 40-562B-022-88X4 is a high density BRIC4 matrix module with a size of 88x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8x2 RF Matrix 1.5GHz 50 SMA
40-750-521
Matrix Switch Module
The 40-750-521 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMA coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
Product
PXI Solid State Matrix Module, 8x2, 30 A
40-555B-011
Matrix Switch Module
The 40-555B-011 is a high current 8x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
LXI 1GHz 75ohm 16x4 Matrix
60-732-003
Matrix Switch Module
The 60-732 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-732 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
Product
4x8 2 Wire USB Modular Switch Matrix
U2751A
Switch Module
The U2751A USB Modular Switch Matrix offers a flexible connection path between the device under test and the test equipment, thus allowing different instruments to be connected to multiple points on the device under test at the same time. This instrument is able to support measurements at a high bandwidth of up to 45MHz. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity
-
Product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
SPST Switch
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
LXI HighDensity 160x16 2A Matrix with BIRST
60-554-025
Matrix Switch Module
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI 2 Slot BRIC 10x32 1-Pole (2 sub-cards)
40-562A-221-10X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.As listed in the manual, page 33, using Slots 1 and 2. Slot 3 can be used only if it is programmed to be used.
-
Product
PXI 8 Slot BRIC 120x16 2A 1-Pole Matrix
40-598-105
Matrix Switch Module
The 40-598 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-598 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Functional Test
UTS
Functional Test
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
Product
PXI 34x4 Signal Insertion and Monitor Matrix
40-525A-001
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also availablein a 16x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system. Each pass thru connection from LX to X can be open or closed to allow the programmatic disconnection of the signal to check the response of the UUT. The matrix can be used to connect test equipment, such as a DMM or scope, to monitor the pass thru signals via Y connections while the LY connections can be used to insert a fault condition or insert external signals. When external signals are injected the LX connections can be opened and the LY connections closed.
-
Product
SDN Switch Compliance Tester
SDN-WSCT
-
*Provides clear comparisons of White Switches for implementation in the SDN network. *Includes testing of multiple forwarding tables pipeline, testing switches in hybrid mode and certification of VxLAN virtual networking.
-
Product
PXI 12-Slot BRIC Matrix, 84x12 1-Pole (2 sub-cards)
40-558-121-84X12
Matrix Switch Module
The 40-558-121-84x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 504x12 1-Pole (12 sub-cards)
40-558-121-504X12
Matrix Switch Module
The 40-558-121-504x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
FADEC/EEC Test Platform
Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
PXI 4 Slot BRIC 115x16 1-Pole (5 sub-cards)
40-560A-021-115X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI Microwave Matrix, 10GHz, Single 8x4, Terminated With Loop-Thru
60-750-184-C
Matrix Switch Module
The 60-750-184-C is a single 8x4 10GHz microwave matrix with internal termination and loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
PXI/PXIe RF Matrix, 16x2, 100 MHz, 75 Ω SMB
40-728A-101
Matrix Switch Module
The 40-728A-101 (PXI) and 42-728A-101 (PXIe) are 16x2 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector. They provide a simple and scalable bidirectional matrix for RF signals and are intended for the construction of high performance switching systems. All X and Y connections have isolation switches.
-
Product
8-Slot BRIC, 252x12, 1 Pole, PXI Matrix (6 Sub-cards)
40-559-801-252x12
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI Dual Microwave Transfer Switch 26.5GHz 50 SMA
40-782A-532
Switch Module
The 40-782A-532 is a dual transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
TSP100 Switch Probes
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI 64x4 Matrix Module, 1-Pole, 2A, 60W
40-585A-001
Matrix Switch Module
Our model 40-585A, along with the following models 40-584, 40-586A, 40-587A are high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays.
-
Product
PXI Hybrid Dual Transfer Switch, DC to 26.5 GHz
M9156C
Switch Module
M9156C PXI Hybrid Dual Transfer Switch, DC to 26.5 GHz
