Laser Systems
-
Product
Automatic System
-
By combining with Hardness Tester, stage control is automated in indent/multi-pointmeasurement to reduce the dispersion caused by each operator. This system is very effective for large-scale rationalization and energy saving.
-
Product
Multiple Angle Laser Ellipsometer
PH-LE
-
The multiple angle laser ellipsometer provides film thickness, refractive index and absorption index at the HeNe laser wavelength 632,8 nm with an extraordinary precision and accuracy. It can be utilized to characterize single films, multiple layer stacks and bulk materials.
-
Product
Nitrogen Laser
NL100
-
Stanford Research Systems, Inc.
The NL100 Nitrogen Laser is ideal for fluorescence measurements, MALDI-TOF mass spectrometers, and other pulsed UV radiation experiments. It provides 3.5 ns pulses at 337 nm (UV), with repetition rates up to 20 Hz.
-
Product
Laser Head Cable, 7 m
10881E
-
Provide reliable power with this spade lug that connects the laser head to multiple laser boards.
-
Product
Analytical Systems
MEXA-Series
-
Quality and performance are our goal. As legislation on vehicle emissions grows more stringent, attention remains focused on next generation engine and after-treatment platforms. HORIBA analyzers and total systems provide for every need from R&D to emissions certification for engine development.
-
Product
Mobile Systems
-
Advanced vehicle-based platforms for real-time detection and identification of CBRN threats in complex and variable urban environments.
-
Product
System Components
-
For demanding computational tasks, Rohde & Schwarz offers the versatile, flexible equipment you need for everyday use – from the system controller and switch unit to the test chamber. All feature excellent EMC shielding, reliable test results and modular solutions.
-
Product
Thermopile Laser Power Measuring Heads
HP Series
-
The HP25S head is specially designed for portable applications through the use of a smaller heat sink. This gives the head smaller dimensions but means that high powers are only possible for a short time.?
-
Product
GPS Systems
-
High accuracy 100Hz GPS with Real-time Kinematics (RTK) correction for the most precise position-based test and measurement applications.
-
Product
In-Situ Cross- Stack Laser Analyzer
-
LS25 is an in-situ analyzer for non-contact measurement of the concentration of gases. The measuring principle of the LS25 is based on the principle of single line spectroscopy (Tunable diode laser absorption spectroscopy, TDLAS). A single cross-sensitivity-free absorption line of the gas to be measured is selected in the near infrared range. A single-mode diode laser operating at room temperature scans the respective absorption line. By using an opposite receiver, the absorption caused by the sample gas is measured and from this the concentration is calculated. An automatic correction for pressure and temperature changes is possible. In addition, the transmission is displayed respectively output as a signal for preventive maintenance.
-
Product
In-Sight Vision Systems
8000 Series
-
This family of ultra-compact, standalone vision systems deliver industry-leading vision tool performance, in the form factor of a traditional GigE Vision camera. Measuring just 35mm x 32mm x 76mm, all In-Sight 8000 series models feature power over Ethernet (POE), and provide the best standalone vision system option for integrating into small spaces.
-
Product
Koheras Single-Frequency Fiber Lasers
-
Koheras single-frequency lasers are longitudinally single-mode and offer extremely low phase- and intensity noise levels. Available in the Erbium or Ytterbium wavelength ranges and with frequency conversion to many other bands.Reliability is our highest priority and the all-fiber DFB design ensures robust and reliable operation for thousands of hours.
-
Product
Meter Test System
MTS-100
-
Kongter Test & Measurement Co., Limited
This Meter Test System features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 120A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
Dimensional Metrology Systems
-
We are a global provider of optical industrial measurement technology for quality assurance of complex components with tight tolerances. With Bruker Alicona measurement systems, users measure dimension, position, shape, and roughness by using only one optical sensor. Measurement systems are applied in both research and directly on the shop floor.
-
Product
Real-Time Operating System
RTXC
-
*Hard real-time operating system.*High performance in a small package.*Tested reliability.*Flexible and adaptable.
-
Product
VPX Processing System
CRS-D4I-3VB1
-
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
Product
System Test Fixture
-
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
Product
Capacitance Sensor Systems
-
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
-
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
Cogging Test System
CTS
-
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
Product
Precision Measurement System
OmniMic V2
-
Updated software and improved hardwareCompact, portable, accurate, affordableIntuitive software—open the box, start testing in minutesPerfect for setting up home theater systemsOptimized for use with netbooks and laptopsAccurate response down to 5 Hz, fully calibrated, includes FRD fileFor professionals and hobbyists—design and tune speaker systems and arrays
-
Product
Optics Test Systems
Mirror Collimator And Autocollimator
-
Optik Elektronik Gerätetechnik GmbH
Mirror collimator and autocollimator for the entire wavelength range from UV to MIR The compact mirror collimator can be used both as an autocollimator and as a telescope.
-
Product
Laser Diode Modules: 635nm-660nm Visible Wavlength, Elliptical Beam
-
The Optoelectronics Company Ltd
Custom lasing wavelengths, from 405 nm to 852 nm, output power options and laser engraving are available to your specifications. Both standard and custom configurations provide OEMs, end-users and systems integrators with complete cost-effective laser solutions.
-
Product
Haptic Testing System
-
The Air Ventilator Haptic Test System performs automatic functional tests on air ventilation components to measure the force necessary for the execution of movements in the different components of the part. The movements are performed by a 6-axis robot that forces the components of the part to follow the desired routes while storing data on the force expended. This particular machine tests movable fins and knurled wheels by performing four test motions on each fin and two on each wheel.
-
Product
Pin-Pointing System
Protrac®
-
As precise as pre-location is, it will never be able to recognise the deviations of a cable route in the ground. These can only be detected by precise pin-pointing. With its protrac®, BAUR offers different solutions that combine acoustic and electro-magnetic cable fault pin-pointing, sheath fault location and tracing in a single system.
-
Product
Metrology System
Aspect
-
Memory density increases with both layer-pair scaling and tier stacking for memory stacks well over 200 pairs. The Aspect metrology system was designed with these future architectures and scaling strategies in mind. Aspect metrology is demonstrating performance superior to X-ray systems across multiple customer devices through a revolutionary infrared optical system providing full profiling capability to enable critical etch and deposition control, with the speed and process coverage that customers require.
-
Product
Environmental Test Systems
-
Manufactured products can be exposed to both thermal and mechanical stresses.These should not be considered separately, as the effects may be linked.IMV can supply vibration-test systems combined with climatic chambers to provide complete vibration, temperature and humidity environmental testing.These systems can be custom-designed to meet your application.
-
Product
Digital Proximity System
AS-3033
-
The Alta Solutions Digital Proximity System (DPS) combines the performance of a fully API 670 compliant eddy-current proximity measurement system with the flexibility of digital configurability. For the first time in our industry, users can configure their transducer system in the field using a custom field generated curve as well as factory pre-configured calibrations for a variety of probe tip diameters, manufacturers, extension cable lengths, target materials, and linear ranges.
-
Product
FMET Systems
-
The Failure Mode and Effect Testing system allows the shorting of any I/O pin to any other I/O pin, including one of 4 common "Rails". Users can establish rules to prevent unwanted shorting conditions.
-
Product
Laser Module
LDM200
-
Artifex Engineering GmbH & Co. KG
The LDM200 series of laser diode modules are specialized units for high-end applications. The fibre coupled design allows flexible installation and separation of the electrical and optical sections. High quality optics and precision adjustment provide for excellent beam quality and very long collimation distances up to 100m. Customized fixed focus distances may also be provided. The option of choice of pola
