Fuel Injector
-
product
Fuel Cell Test Stations
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
-
product
Fuel Injection Pressure Tester
33900
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
product
MASTER FUEL PRESSURE TEST SET
FPT5000
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
product
Fuel Injection Tester
FIT13A
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifold. Includes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446); Japanese fuel injection systems; a The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
product
fuel Center Products
Secure PCI compliant and easy to install networking solutions for all the data connections in and around your fuel center.
-
product
Signal Injectors
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
product
Hydrogen Fuel Cell
Honeywell Aerospace Technologies
Honeywell has a decades-long history of innovation in power generation for all kinds of aerospace and defense applications, which was further strengthened by the 2020 acquisition of Ballard Unmanned Systems, a global leader in fuel cell technologies for unmanned aerial vehicles (UAVs).
-
product
High-Precision Fuel Flow Measurement System
It enables to keep the temperature fluctuation of the circulation flow path in the system within ±0.2 °C (for 1 minute), which achieves stable fuel flow rate measurement.
-
product
Interface Cards / PoE Injector
Gigabit Ethernet with PoE allows for single cable camera solutions, simplifying installation and maintenance. For those who will be externally powering the camera we offer a single port Gigabit Ethernet card and a PoE injector unit.
-
product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
product
Basic Fuel Pressure Tester Kit
FIT450
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
product
Line Injector
J2120A
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
product
High Precision Fuel Flow Meter
This system measures fuel consumption of an engine operated in steady state with high accuracy.•0.02 to 90L/h and 4500:1 wide range measurement (H type)•Keep the temperature change of the circulation flow passage in the device within ±0.1℃ (variation per 1 minutes) to provide stable measurement.•Pipe arrangement which minimizes air bubbles that enter the system reduced the factor error causes.•Resolution has been improved by using an encoder with 1200P/R (Ten times of number of pulses to the existing model.)
-
product
On-vehicle Ultrasonic Fuel Flow Meter
RealFlow
The RealFlow ultrasonic sensor from HORIBA represents a breakthrough in fuel flow measurement technology, for both the compactness in size and its high level of accuracy.The RealFlow has been designed for the ultra low-volume fuel flow conditions found in today’s high-efficiency road car engines, making it an ideal tool for R&D as well as emissions testing to the RDE and WLTP standards - especially with its ability for true engine bay installation due to being so compact in size - a real game changer in the Automotive industry!
-
product
Current Injectors / Relay Testing
RTS series & SC-10
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Ranges: 1A to 200A AC, Auxiliary output AC / AC+ DC, TRMS Digital metering.
-
product
DURAMAX PVC/EVAP FUEL RAIL PRESSURE RELEASE TOOL
MST144
*Works on 2011 and later Duramax LML engines*Saves time by eliminating the need to remove EGR cooler and fuel rail*Quickly removes the Duramax fuel pressure release valve which otherwise would take up to 8+ hours to service
-
product
MFP-570 Main Fuel Pump
The MFP-570 provides main engine burn flow as well as servo flow and engine actuator flow. This two-stage “cartridge type” fuel pump is designed to be inserted directly into the engine fuel metering unit.
-
product
Fuel Injection Pressure Tester w/2 Gages & Quick Couplers
53950
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
product
Vacuum and Fuel Pump Tester
DVG1
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
-
product
Fuel Display Unit Tester
MS 1125
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
product
Fuel Cells
continuously variable contact pressure ensures complete reproducibility of the test conditions ● independent of the thickness of the fuel cell components due to the self-adjusting piston and special sealing concept ● no connection and disconnection of hose- or cable connections for the exchange of cellFixture necessary ● fast &Easy clamping of the cellFixture without tools and precise exchange of the internal cell components ● maximum power density by determining the optimal contact pressure on the active cell surface ● developed for high stress in the field of quality assurance and laboratory environment
-
product
PEM Fuel Cell Test Stations
Available with Greenlight''s integrated ''Intelligent Fuel Cell Diagnostics'' capabilities:FCDXTMCE certification including optional 3rd party verificationIndustry-leading software and diagnosticsAutomated reformate gas simulation (blending)5 different gas humidification technologies available, including Greenlight''s optional Rapid Response humidification system24/7 unattended operation with Emerald control and automation softwareIndustry leading cell voltage monitoring accuracyUser-adjustable safety featuresFuel cell stack leak testingOptional integrated environmental chambersOptional high temperature configuration, specifically designed for PBI membrane researchOptional DMFC configurationWorldwide service and support
-
product
Fuel Cell Test Station
E1PS is glad to bring you a low cost method to test fuel cells and produce professional test data results for under $1,000.00, fuel cell included! The Fuel Cell Test Station comes complete with everything but the hydrogen. There are three meters*, a load box, forced air housing and a fuel cell.
-
product
Fuel Injection Pressure Tester with 2 Gages
33950
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
product
MASTER FUEL PRESSURE TEST KIT
FIT550
*Performs running, residual, rail and flow rate pressure tests*Large, easy-to-read 3-1/2" dual-scale gauge reads 0-100psi and 0-700 kPa*Kit includes: 50+ adapters, fittings, 48" hose, pressure relief and fuel discharge hose to test most domestic and foreign fuel injection systems*Also includes quick release couplers and adapters to fit other fuel injection test kits*For use with gas engines only
-
product
Fuel Injection Pressure Tester with 2 Gages & Quick Couplers in Storage Case
53980
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
product
Fuel Analysis
The GRABNER INSTRUMENTS MINISCAN IR Vision is a truly portable and fully automated FTIR fuel quality tester that allows fast and highly precise analysis of gasoline, diesel and jet fuels directly in the field. The ParaFuelTM analyzer is used specifically for process applications.
-
product
COMPRESSION, VACUUM AND FUEL PUMP TESTER COMBO SET
MCVK
*Tests compression on all domestic and import cars and trucks with gasoline engines*Compression tester kit includes: 2-1/2" gauge with dual inch/metric readings: 0-300 psi and 0 to 21 kg/cm2, 14mm/18mm solid short adapter, 14mm/18mm long flexible adapter and 14mm long reach adapter*Checks vacuum and fuel pump pressure and locates air leaks in fuel lines, vacuum operated chokes and emission control systems on all domestic and import cars and trucks with gasoline engines
-
product
Fuel Injection Pressure Tester with 2 Gages in Case
33980
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with multi-port and some throttle body injection (TBI). Test all Chrysler cars with multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.
-
product
Fuel Injection Pressure Tester with Quick Couplers
53900
Quick couplers provide for fast and easy hook-up. Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI. Use on Ford older TBI systems not equipped with small Schrader test valve. Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR). Supplied with instructions in a vinyl pouch.
