Reflectance
fraction of the electromagnetic energy.reflected.
-
Product
SINE FBI Charts
-
There are two SINE Sinusoidal arrays designed for FBI applications: the SINE M-13-60-S-RM and the SINE M-13-60-FBI Kit.The SINE M-13-60-S-RM was designed jointly by the Federal Bureau of Investigation, of Washington DC, and MITRE, of Bedford MA. The primary function of this Target is for computing Modulation Transfer Function (MTF) evaluation in live scanner fingerprint systems for conformance to Integrated Automated Fingerprint Identification Systems (AFIS) image quality requirements. The array is on reflective material measuring 16mm x 16mm with sinusoidal arrays ranging in frequency from 1.0 to 10.0 cycles per mm; with nominal modulation of the sinusoidal areas at 60%. The top and bottom rows are density scales, from 0.20 to 1.20 densities.The SINE M-13-60-FBI Kit consist of two individual components, the SINE M-13-60-1X-RM and the RR1-N-RM Ronchi Ruling grating.
-
Product
Red Tide Spectrometers
USB-650
-
USB-650 Red Tide spectrometers are ideal for teaching about UV and visible absorbance, reflectance and emission applications. They are preconfigured, ready-to-use spectrometers that come in several different options. Fully integrated – USB650-UV-VIS and USB650-VIS-NIR models are preconfigured, ready-to-use systems.
-
Product
Integrating Spheres For Reflection, Transmission And Absorption
-
Integrating spheres and accessories optimized for the measurement of reflection, transmission, absorption and photoluminescence.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
RF Bridge, 50 Ohm, 300 kHz to 3 GHz
86205B
-
The Keysight 86205B high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
Polarizing Beamsplitter (PBS)
-
Polarizing beamssplitters split randomly polarized beams into two orthogonal, linearly polarized components. S-polarized light is reflected at a 90 degree angle while P-polarized light is transmitted. Polarizing beamsplitters come in cube form, but custom geometries are available.
-
Product
Measurement Microphones
-
The microphone bodies contain the preamplifier. They combine high dynamic range and wide frequency range with low noise. These measurement microphones connect via the ASD Cable to the XL2 Audio and Acoustic Analyzer, e.g. for measurements at remote locations or to reduce acoustic reflections.
-
Product
Contactless Lifetime Measurement and Inhomogenities Device
MWR-2S-3I
-
Lifetime determination is based on measuring photoconductivity decay after pulse light photo-exciting with usage of reflected microwave as probe.Simultaneous IR light transmission gives possibility to detect any inhomogenity insidesilicon brick and made 3D image of defects.
-
Product
Distance Sensors
-
SICK has a wide range of optic and ultrasonic solutions that measure from sub-microns to kilometers. They solve measuring, detecting and positioning applications using triangulation and time-of-flight modes. Sensors using triangulation are ideal for short-range, highly precise measurement. They can inspect miniature parts, thickness and shape, etc. Time-of-flight sensors work at longer distances, are not influenced by reflectivity or ambient light − perfect for positioning AS/RS, rail cars and gantry cranes.
-
Product
Integrating Spheres
-
Instrument Systems Optische Messtechnik GmbH
Determination of radiant power or luminous flux from light sources with the aid of integrating spheres is one of the most important procedures in photometry. Designed as a hollow sphere whose inner surface is coated with a diffusely reflecting material, the integrating sphere ensures complete integration and mixing of light radiation. This is then output on a detector port for measurement.
-
Product
Light Sources
-
For applications such as transmission, absorption, and reflection, illumination sources are needed. Avantes offers a wide range of different types of light sources, to suit your specific application needs. An overview of the different types of light sources can be found below.
-
Product
Total Reflection X-Ray Fluorescence (TXRF) Products
-
Total Reflection X-Ray Fluorescence (TXRF) Products by Rigaku
-
Product
Portable Digital Ultrasonic Flaw Detector
MFD350B
-
Your product description goes here.MFD350B Portable Digital Ultrasonic Flaw Detector is a economical and practical model improved on MFD500B. Except for the differences of its measuring range, working frequency and transmitted pulse parameter, the other performances are the same as MFD500B.Based on ultrasonic pulse reflection testing principle, MFD350B controls all testing process by the mini-processor. And it has low power design and can do charge with two models such as online chargeing and offline charging. And it can work continuously about 8 hours.With large capacity, digital multi-color TFT LCD, original imported stable IC, small size, light weight, stable performance and favorable price, MFD350B is one of our company’s high promoted super cost performance and economically ultrasonic flaw detector.
-
Product
SWR / Power Meters
-
A device used primarily by radio operators to measure the Standing Wave Ratio (SWR) and forward and reflected power in a transmission line, like a coaxial cable.
-
Product
Nuclear Safeguard Systems
-
Nuclear Safeguards are measures to verify that States comply with their international obligations not to use nuclear materials (plutonium, uranium and thorium) for nuclear explosives purposes. Global recognition of the need for such verification is reflected in the requirements of the Treaty on the Non-Proliferation of Nuclear Weapons (NPT) for the application of safeguards by the International Atomic Energy Agency (IAEA). Also, the Treaty Establishing the European Atomic Energy Community (the Euratom Treaty) includes requirements for the application of safeguards by the European Commission. Organizations such as the IAEA and EURATOM and others are tasked with ensuring declared amounts of material are indeed present in the facilities in which they are stored and that such material is not being diverted to other uses.
-
Product
LXI WTB Terminator, 100 ohm
60-983-001
Terminator
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Product
Qwiic Spectral Sensor
AS7341
-
The AS7341 is an 11-channel spectral sensor from AMS that covers wavelengths between 350nm to 1000nm. It features eight channels that span the visible spectrum and there's a channel for Near IR, clear, and flicker detection up to 2kHz. Point a spectral sensor at an object and it measures the reflected or absorbed electromagnetic wavelengths.
-
Product
Dual-Directional Couplers
-
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
Product
BNC To BNC Cable, 50 Ohm, 0.9 M
781887-01
Coax Patchcord
Connects measurement and signal generation devices. Model options include industry-standard coaxial connector types including BNC, SMA, SMB, and MCX. Long cables can act as antennae picking up extra noise that can affect measurements, so ensure you select only the length required for your test system. Also look at the impedance of your test system and consider buying a cable with the same impedance. Matched impedance can maximize the power transfer or minimize signal reflection from the load of your system.
-
Product
Temporary Bonding Systems
-
Temporary bonding is an essential process to offer mechanical support for thin or to-be-thinned wafers, important for 3D ICs, power devices and FoWLP wafers, as well as for handling fragile substrates like compound semiconductors. A device wafer is bonded to a carrier wafer with the help of an intermediate temporary bonding adhesive, allowing the typically fragile device wafer to be processed with additional mechanical support. After the critical processes, the wafer stack is debonded. EVG’s outstanding bonding know-how is reflected in its temporary bonding equipment, which has been provided by the company since 2001.
-
Product
Laser Flash Photolysis
-
This system that makes complex electronics, cumbersome software and large optical benches a thing of the past. The LFP system incorporates everything needed except the excitation laser. This is a simple, yet powerful instrument, ready to perform a wide range of time resolved kinetic and spectroscopic measurements involving transient absorption or diffuse reflectance. The LFP system, including the monochromator and digitizer is completely computer controlled, making it easy to obtain
-
Product
Self-contained Photoelectric Sensors
PZ-V/M Series
-
Automatic Calibration Photoelectric Sensors. Detections are unaffected by variations in target color or angle. Excellent resistance to dust and dirt. One touch, fully automatic calibration. Unaffected by highly reflective target backgrounds. 40 model variations available including quick disconnect types. High-power red LED(Except for PZ-M71/V71)
-
Product
3D Sensors (Main Screen)
surfaceCONTROL
-
surfaceCONTROL sensors are used for 3D measurements and surface inspections. The sensors use the fringe projection principle to detect diffuse reflecting surface and to generate a 3D point cloud. This point cloud is subsequently evaluated in order to recognize geometry, extremely small defects and discontinuities on the surface. Sensors with different measurement areas are available. This enables the inspection of the finest of structures on components as well as shape deviations on large-area attachments. Powerful software packages are available for evaluation and parameter setting.
-
Product
Spectrophotometer Solutions
-
United Power Research Technology Corporation
UPRtek provides project-based spectrophotometer solutions, which analyze and identify materials through light absorption, reflection, transmission and fluorescence.
-
Product
Optical Fiber Cable Testing Equipment
-
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
Product
Single connector for a HG cable, and two HM connectors
MVNA-8-350-2
-
The lower part of the Central Unit model MP-8-350-2 has a single connector for a HG cable, and two HM connectors (Fig. 9). Two Harmonic Mixers can work simultaneously, for instance HM2 detecting transmission through the DUT, and HM1, at port 3 of a directional coupler, detecting reflection from the DUT.
-
Product
Ultrasonic
VEGASON
-
In non-contact ultrasonic level measurement, the sensor emits ultrasonic pulses in the direction of the medium, which then reflects them back.
-
Product
Fully Automatic Colorimeter
DRK103C
-
Shandong Drick Instruments Co., Ltd.
(1)5 inch TFT color LCD touch screen, the operation is more humanized, new users can be mastered in a short period of time using the method.(2)Simulation of D65 lighting lighting, using CIE1964 complementary color system and CIE1976 (L*a*b*) color space color difference formula.(3)The motherboard brand new design, using the latest technology, CPU uses 32 bits ARM processor,improve the processing speed, the calculated data is more accurate and rapid electromechanical integration design, abandon cumbersome testing process of the artificial hand wheel is rotated, the real implementation of the test program, a determination of the accurate and efficient.(4)Using d/o lighting and observation geometry, diffuse ball diameter 150mm, diameter of the testing hole is 25mm.(5) A light absorber, eliminate the effect of specular reflection.(6)Add printer and imported thermal printer, without the use of ink and color, no noise when working, fast printing speed.(7) Reference sample can be physical, but also for data,? Can store up to ten only memory reference information.(8) Has the memory function, even if the long-term shutdown loss of power, memory zeroing, calibration, standard sample and a reference sample values of the useful information is not lost.(9) Equipped with a standard RS232 interface, can communicate with computer software.
-
Product
Power Supplies
CU-400B
-
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
SparkFun ToF Range Finder Breakout for VL6180
12784
-
This is the SparkFun "Time-of-Flight" Range Finder, a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected light intensity or reflected angles to determine range, the VL6180 uses a precise clock to measure the time it takes light to bounce back from a surface. This affords the ToF Range Finder and VL6180 a great benefit over other methods because it can be much more accurate and more immune to noise. Does this technology sound familiar? Well it should, it's the same means cellphones use to detect when the caller is holding their phone to their ear.
