ISDN Simulators
See Also: ISDN Testers
-
Product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
2 Port T1/E1/PRI + 8 port BRI-U ISDN
CH-8BRI-U-MOD-2PRI
-
This unit has two PRI ports and 8 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
Large Area Solar Simulators
-
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Protocol Simulation
-
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
Product
Target simulators
-
Simat simulator is an advanced hardware simulator capable to simulate in infrared range several targets on quasi uniform background. In detail Simat simulator is a modular image projector capable to simulate in infrared range variable intensity, variable angular size, variable spectrum, spatially and temporally dynamic airborne type targets on quasi uniform background. Basically the aim of Simat to enable simulation typical airborne targets like aircrafts or helicopters for infrared imaging sensors used for surveillance of these targets. Optionally Simat can be modernized to enable simulation in both IR and UV/visible ranges as the projectors are built using broadband reflective optical elements.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Lightning Impulse Simulation Tester
KT-6030iG
-
Most of all electric systems and equipments are weak against the lightings(direct, inductive lightning). In fact, those electric equipments are broken mainly by lightning.This Lightning Impulse Simulation Tester is certificated to IEC 61000-4-5, and generates the similar impulse with huge rush currents and tests the safety of the power systems and equipments.
-
Product
Avionics Test & Simulation Interfaces
Interface
Connect your PC laptop, desktop and tablet computers to avionics databuses with pocket-sized Ballard USB interfaces. Ease of use, versatility and comprehensive databus functionality have made these rugged adapters the industry favorite for avionics test, analysis and simulation in the lab and in the field. Avionics labs routinely integrate Ballard interface cards and full-featured network appliances into their test setups for powerful and reliable databus connection.
-
Product
ISDN Chip Set
Emutel Symphony
-
Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment.
-
Product
MAGNESIUM ANODE SIMULATOR
CS-1
-
The CS-1 portable Magnesium Anode Simulator is an ideal DC current source that will allow the user to see what the addition of a magnesium anode on their system will do to Pipe to Soil measurements and other C.P. tests.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Transducer Simulator
Model 7
-
Impedance: 350 ohms nominal. Output Ranges: Fixed rotary switch. 0 to 3 mv/v in 6 steps of .5 mv/v .
-
Product
Custom Solar Simulation
-
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
-
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
Product
Solar Simulator
Unisim Compact Solar Simulator
-
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available). The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
Fully Reflective Solar Simulators
-
Sciencetech manufactures four high power versions of class AAA fully reflective solar simulators. Sciencetech''s proprietary fully reflective design uses metal coated mirrors and passes the whole spectrum, no compromise. This is a distinct advantage over refractive based systems that are limited by the properties of the transparent material used.
-
Product
Panel-mounted Amplifier(Power System Simulation )
PA30Bi-H
-
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
Product
MIMIC® IOS Simulator
-
MIMIC IOS Simulator is a command line simulator that fully supports Cisco IOS® software as well as NX-OS, JUNOS, NETCONF, other command line interfaces and SNMPv1, v2, v2c, v3. You can simulate up to 100,000 devices in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. You can access devices using Telnet, SSH and SNMP. Changes made using one protocol is reflected in the other.
-
Product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Mechanical Simulation in Matlab
-
There are variety of numerical possibilities in the MATLAB and Simulink simulation environment. For those simulation environments we offer you various toolboxes that allow you to perform simulations easily and efficiently. These toolboxes can be combined with all available ways of MATLAB and Simulink. Our toolboxes can provide you support in the following areas: Analysis of structural dynamic behavior, Vibration and noise abatement, Design of active systems, Model Reduction, Ansys-Matlab interface.
-
Product
Altitude Simulation Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Altitude Simulation Test Chamber
-
Product
USB SmartCable For AFDX®/ARINC664P7 Test And Simulation With 2 Full Duplex Ports Programmable For 10/100 Mbit/s
ASC-FDX-2
-
USB SmartCable for AFDX®/ARINC664P7 Test and Simulation with 2 full duplex Ports programmable for 10/100 Mbit/s. Versions available for both Airbus and Boeing Variants of ARINC664P7.
-
Product
Vehicle Network Simulator
OBD Simulator™
-
Simulate Vehicle Network Messaging for OBD CAN, J1939 CAN, J1850 VPW, J1850 PWM, ISO-9141 and KW2000.
-
Product
Environmental Simulation
-
During the development phase of new products, we analyze the weak points in simulation tests and test the products for environmental influences. The relevant standards are used as the basis for the simulation tests.
-
Product
Altitude & Space Simulation Test Chambers
-
Weiss Technik’s vast experience with altitude, thermal vacuum, low temperature and space simulation test chambers can provide you with the right solution. We offer both pre-engineered and custom altitude chambers for ultra-low cooling, extended mbar, and extended temperature ranges that will meet your testing exact requirement.
-
Product
Linktropy Network Delay Simulator
-
Linktropy Emulators Provide Affordable Network Emulation for Accurate, Repeatable Performance Testing at Speeds up to 1 Gbps
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
