kV Cable
-
product
Cable Avoidance Tool
CXL4
The CXL4 is a dual-frequency (33+131kHz) Cable Avoidance Tool.In-built Data Logging, Bluetooth™ connectivity and GPS tracking options. Designed for use with an SGA4 or SGV4 Signal Generator.
-
product
Ribbon cable headers
HDRterm50
Ribbon cable headers are commonly used with IP compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The HDRterm50 converts from 50 pin ribbon cable to a 50 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
-
-
product
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 8 SMA Plugs
540259010253
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 8 SMA Plugs
-
product
Cable Fault Locators
Every day, GAOTek cable fault locators are used by electricians and technicians to find faults and breaks in underground electrical and communications cables.
-
product
PC-NET Cable Tester
PR-09
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m HV, Exit Towards Pin 1
A050DM5-050DF5-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Network & Cable Testers
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
product
Cable Assembly, Type-N (m) to Type-N (m), DC to 6.0 GHz
11500A
The Keysight 11500A is a 180 cm (71 in) type-N male to type-N male cable assembly with a frequency range of dc to 6.0 GHz.
-
product
Cable Length Meters
Reflect a pulse.through the cable measuring length (time domain reflectometry).
-
product
Cable Verifiers
VDV II Series
The new VDV II Series are easy to use cable testers that check the integrity of copper cables commonly found in domestic, commercial or industrial voice, data or video installations, including telephone wiring, data network and video/security cabling.
-
product
Microwave Cables
Silicon Dioxide cable is a high stability cable at high temperatures and high frequencies. Because of thishigh stability silicon dioxide cables are currently used in nuclear reactors, decoy boxes, radars, satellites,aircraft and sophisticated missile applications. Measure Tech's Silicon Dioxide cable assemblies are excellentfor operation in extreme environment conditions where stability is crucial. Measure Tech's Silicon Dioxidecable is currently used by Lockheed Martin in their JASSM missiles. Measure Tech currently has 100% on timecdelivery for the Silicon Dioxide Cables delivered to Lockheed Martin.
-
product
Cable Analyzer
MM-HTDR MediaManifold
The Crestron MM-HTDR MediaManifold Cable Analyzer is a portable handheld device used to determine the length and integrity of RG6 cable runs. Using "time domain reflectometry," the MM-HTDR can measure cable lengths up to 1099 feet.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Unterminated (Tinned Ends), 1m
40-972B-200-1m-MU
This male rear exit to unterminated 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50 wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to the product by screwlocks.
-
product
Cable Fault Location
BAUR Prüf- und Messtechnik GmbH
BAUR cable fault location devices and systems cover the entire cable fault location process: During pre-location, the position of the fault is roughly located. The subsequent pinpointing enables precise determination of the cable fault. You can use various measurement methods depending on the kind of fault and cable type.
-
product
50 Ohm MCX to MCX Cable Assembly
40-977-561-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
RET Cables
Remote Electrical Tilt (RET) systems are being installed in many wireless infrastructure sites to optimize signal patterns. The RET control cable between the control unit and the antenna is the least appreciated system component, unless you cannot get one to complete your installation.
-
product
Cable Assembly, 50-Pin D-Type, Male to Female, 0.5m HV
A050DM5-050DF5-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m
A037DF4-C-0A050
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Tracers
179 CB
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m HV, Exit Towards Pin 1
A050DM5-T-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product
-
product
Cable Fault Locator
TX2002
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
RF Cable Assemblies
Transmission lines for radio frequency (RF) signals traveling from one point in a system to another (e.g., PC board to PC board, PC board to antenna, equipment to antenna, equipment to equipment, etc.).
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
Wire And Cable
Chengdu Mengsheng Electronics Co., Ltd.
We provide a variety of wire and cable products, including insulated wires, power cords, stranded wires, solid wires, wiring harnesses and connectors. Our products are widely used in security, medical, communications, instrumentation, medical, home appliances, auto parts, military, aerospace and other industries. Our products strictly comply with the product certification standards of countries and regions such as UL in the United States, VDE in Germany, CE in the European Union, and BS in the United Kingdom.
-
product
Cable Testing Service
Cable testing service available from Cimbian includes:Helping you with the test specificationBuilding the test interface, where necessaryCreating the test programBarcodingTest reportsSimple continuity testingMeasurement/verification of resistances and diodes (traceable to national standards)Hi-Pot testing to 1500VDC / 1000VAC
-
product
Cable Assembly, 160-Pin DIN41612, Male (With Female Screwlocks) To Female (With Male Screwlock), 1m
40-970-160-1m-MF
The cable assembly is suited for direct connection to Pickering Interfaces products using a Female DIN41612 connector. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks)
40-970B-200-1m-FF
This female to female 1m cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cable and the connector assemblies can be secured to their mating connectors by female screwlocks.
