Insulation Resistance Testers
-
product
Surface Insulation Resistance Testing
AutoSIR2™
One AutoSIR chassis can hold between 1 to 16 measurement cards and can monitor up to 256 x 2-point test patterns or 78 x 5-point test patterns, or 32 x 9-point test patterns at selectable intervals from minutes to days. Each channel is current limited (1 M Ω), ensuring that dendrites are preserved for failure analysis. The frequent monitoring capability provides a full picture of the electrochemical reactions taking place on a circuit assembly, and provides early trend analysis enabling tests to be curtailed, thus saving considerable test time and money.
-
product
Earth Contact Resistance Tester
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
product
LD/LED ESD Tester
Hanwa Electronic Ind. Co.,Ltd.
Performs automatic destructive evaluation of Lazer-Power.
-
product
Transformer DC Winding Resistance Tester
HTZZ-50A / 246
Wuhan Huatian Electric Power Automation Co., Ltd.
Measurement transformer around the group and large power inductor dc resistance ideal equipment.
-
product
Stator Tester
DZ800d/e Series
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of Y-type three-phase motors, single-phase primary and secondary motors, single0phase multi-speed motors, automobile generators, brushless motors, series excitation motors servo motors, and synchronous motors.
-
product
Hardness Tester
NB3010 Series
Newage Testing Instruments, Inc.
A basic Brinell hardness tester with semi-automatic operation. NB3010 is a cost-effective Brinell tester using deadweights with a pneumatic load system to apply and remove the loads. Operates in most all Brinell scales.
-
product
Power Supply Tester
UTS-325
UTS and STS systems are based on the Autotest A100 Instrument bus which provides a GPIB interface to load and source control and monitoring along with a measurement path matrix, timer/counter/trigger and peak detector instruments, user assignable relays and drivers.
-
product
Resistance Meter
MT16-4L
М-module МТ16-4Л is a mezzanine module (hereinafter referred to as a mezzanine), designed to measure the resistance of resistive sensors using a four-wire measurement circuit in sixteen channels (sixteen-channel digitizer). М-module МТ16-4Л is installed on the mezzanine carrier - module НМ-М and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NM-M module. The NM-M module, together with the mezzanines installed on it, forms a VXI module of the C-1 size and is used to create information measuring VXI systems.
-
product
Advanced Powder Resistance Kit
PRK-130
The PRK-130 is an advanced kit that includes the PRF-930 Powder Resistance Fixture for measuring the bulk resistance of powder and granulated materials. Test material is placed in the cavity between the measurement plates. Once a measurement has been made in ohms, a fixture calculation, or correction factor, converts the resistance measurement to volume resistivity in ohm-cm.
-
product
Polymer Testers
Accurate polymer testing requires dedicated polymer testing instruments. We offer a range of polymer testers for measuring density and intrinsic viscosity (IV).
-
product
Pull-Off Adhesion Tester
506
The Elcometer 506 are lightweight, portable and easy-to-use adhesion testers available in analogue or digital gauges and are suitable for measuring the pull-off adhesion of coatings up to 50MPa (7250psi) either on-site, or in the laboratory.
-
product
Semiconductor Testers
Our integrated team of semiconductor test innovators delivers a complete system tailored to achieve your specific objectives, incorporating:Test strategyHardware designSoftware development and integrationManufacturingInstallationProgram managementOngoing support
-
product
Washing Fastness Tester
TF418E
TESTEX Testing Equipment Systems Ltd.
Washing Fastness Tester is mainly used to test the color fastness of textiles to washing or dry cleaning, i.e., the ability of textiles not to fade or change color after washing or dry cleaning.Washing Fastness Tester complies with AATCC 61, ISO105-C06/C10, etc.
-
product
Panelized PCB Tester
Removable nests are designed to configure base test system to accept panelized circuit boards for rapid functional test.
-
product
Insulation Tester
The unit has select able long duration and momentary operation switches for high resistance measurements.
-
product
Medical Leakage Tester
GLP2-CE
For testing the leakage current of medical equipment to standards EN 60990 + EN 60601.
-
product
Line Tester
LT51
The LT51 Line Tester is a portable handheld battery powered instrument for Data, DSL, Telephone, Voice Copper Line testing. It combines the features of several pieces of test equipment such as a Level Meter / Spectrum Analyser, Distortion Analyser, Oscillator, Handheld DMM and TDR in the one small lightweight package.
-
product
Impulse Spark Tester
IT-25B
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
product
Bench Hardness Tester
MTR X-SERIES
The bench hardness tester MTR X-SERIES operates to determination through the measurement of electrical resistance. The MTR X-SERIES hardness tester has been designed to solve some of the still unsolved issues in the field of hardness control. Its test principle allows the user to perform measurements in difficult or inaccessible points internal surfaces and gear teeth.
-
-
product
Rechargeable Multifunction Tester
ET4000
The new ET4000 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
Everything about the new ET Series has been designed to save time and make testing easier.
Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .
Supplied with a full range of accessories.
-
product
Resistance Temperature Detectors (RTD) Simulators
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
product
Distribution Transformer Tester
NDB-DOC-3™
The NDB-DOC-3™ is a test instrument designed for distribution networks transformers from 5kVA to 3MVA. It can determine the presence of short circuits or open circuits in the distribution transformer primary winding & also short circuits on the secondary winding.The NDB-DOC-3™ is designed to be operated without disconnecting the transformer’s secondary windings from their loads.
-
-
product
In-Circuit Testers
Whether you’re choosing from our stand-alone manually loaded ICT tester all the way to our fully automatic In-line test system, Acculogic has the solution for you!Acculogic’s Scorpion family of automated test equipment and in-circuit fixture-based testers were created with one underlining theme in mind: “Cost-effective Testing”.
-
product
Isolation Tester UIP
The devices of the UIP (Union Isolations Prüfer) isolation tester series are used to test the pore-free condition of corrosion protection coatings of pipes, vessels or plant system parts. The battery-powered device generates test voltages between 5 kV and 30 kV, which are applied to the grounded test object via test electrodes. The location of a defect is signalized by a spark-over with an additional audible warning.
-
product
Bare Board Tester
1232
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
product
Armature Tester
Qingdao AIP Intelligent Instruments Co., Ltd
This tester is suitable for online or offline detection of various armature electrical properties, such as power tool motors, garden tools, vacuum cleaner motors, small household appliance motors, automobile motors, fitness equipment motors, permanent magnet micro-motors, etc. The tooling of the tester meets the requirements of arbitrary placement of the armature, and can automatically and accurately sort/track faulty solder joints; the equipment startup methods include buttons, remote control, and sliding cover; it meets the armature test of special processes such as double insulation, and automatically identifies solder joints, winding short circuit/open circuit , winding errors, poor welding and other problems; the tester can also automatically count the number of tests, the number of defectives and other data, which is convenient for quality management analysis.The tester test items mainly include:bar-to-bar resistance, diagonal resistance, welding resistance, insulation resistance, ac hi-pot, surge.
-
product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
product
Battery Testers
La Marche Manufacturing Company
This patented battery tester has the capability to store battery discharge curve as a benchmark to analyze battery health trends.
